Dodge dakota 2002 Service Manual page 2621

23 - 46 HOOD
HINGE
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 46
HOOD
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 47
LATCH
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 47
HINGE
REMOVAL
NOTE: It is not necessary to remove the hood to
replace one or both hinges. The hinges can be
replaced one at a time.
(1) Remove the cowl grille. (Refer to 23 - BODY/
EXTERIOR/COWL GRILLE - REMOVAL)
(2) Using a grease pencil or equivalent, mark the
position of the hinge on the hood.
(3) Remove the fender support bolt. (Fig. 1)
(4) Remove the support cylinder. (Refer to 23 -
BODY/HOOD/SUPPORT CYLINDER - REMOVAL)
(5) Remove the hood nuts.
(6) Remove the wheelhouse splash shield. (Refer to
23 - BODY/EXTERIOR/FRONT
SPLASH SHIELD - REMOVAL)
(7) From inside the fender, remove the two hinge
bolts. (Fig. 2)
(8) Slide the hinge forward and remove from the
fender rail.
INSTALLATION
(1) Install the hinge and slide back into position
on the fender rail.
(2) From inside the fender, install the two hinge
bolts and tighten to 20 N·m (15 ft. lbs.).
(3) Install the hood nuts and line up the marks
made previously.
(4) Tighten the nuts to 23 N·m (17 ft. lbs.).
(5) Install the support cylinder. (Refer to 23 -
BODY/HOOD/SUPPORT CYLINDER - INSTALLA-
TION)
HOOD
TABLE OF CONTENTS
page
LATCH RELEASE CABLE/HANDLE ASSEMBLY
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
INSTALLATION
LATCH STRIKER / SECONDARY CATCH
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
INSTALLATION
SUPPORT CYLINDER
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
INSTALLATION
WHEELHOUSE
1 - FENDER
2 - FENDER SUPPORT BOLT
3 - HINGE
11 N·m (8 ft. lbs.).
23 - BODY/BODY STRUCTURE/GAP AND FLUSH -
SPECIFICATIONS)
TERIOR/COWL GRILLE - INSTALLATION)
23
SPLASH SHIELD - INSTALLATION)
. . . . . . . . . . . . . . . . . . . . . . . . . 47
. . . . . . . . . . . . . . . . . . . . . . . . . 48
. . . . . . . . . . . . . . . . . . . . . . . . . 49
Fig. 1 HINGE/FENDER BOLT
(6) Install the fender support bolt and tighten to
(7) Check hood fit and adjust if required. (Refer to
(8) Install the cowl grille. (Refer to 23 - BODY/EX-
(9) Install the wheelhouse splash shield. (Refer to
- BODY/EXTERIOR/FRONT
DR
page
WHEELHOUSE