Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5: Vehicle Identification Number
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
Page 7 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....9 Key-In-Ignition Reminder ....9 Sentry Key —...
Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Windows ......22 Power Windows — If Equipped ... .22 Sliding Rear Window—If Equipped .
Page 9: Things To Know Before Starting Your Vehicle 7
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith.
Page 10: 10 Things To Know Before Starting Your Vehicle
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE continuously to signal that the vehicle has been immobi- lized. If the Security Light remains on during vehicle operation, it indicates a fault in the system electronics. If this option was ordered, all of the keys provided with your new vehicle have been programmed to the vehicle electronics.
Page 11: Ignition And Steering Lock - If Equipped
General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
Page 12: Automatic Transmissions
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your ve- hicle. It may be difficult to turn the key from the LOCK position when starting your vehicle.
Page 13: Door Locks
There is also a battery saver feature that will turn the interior lights off after 15 minutes if the ignition is OFF and a door is left open or the dimmer control is in the interior lights ON position or cargo light ON position. DOOR LOCKS Manual Locks Front doors may be locked, sliding the lock knob rear-...
Page 14: Power Door Locks - If Equipped
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks — If Equipped Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
Page 15 Central Locking — If Equipped Vehicles with security will have a feature called Central Locking. When the key is placed in the door cylinder and turned to the Unlock position, the security will be disarmed, the illuminated entry will be turned on and that door will be mechanically unlocked.
Page 16: Child Protection Door Lock
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system. This label is located near the lock lever.
Page 17: Remote Keyless Entry - If Equipped
REMOTE KEYLESS ENTRY — IF EQUIPPED This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system. To unlock the doors (four door vehicles): Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock...
Page 18: To Lock The Doors
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure. NOTE: All two-door vehicles will be shipped from the assembly plant with this feature disabled.
Page 19: Using The Panic Alarm
Using the Panic Alarm To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound.
Page 20: General Information
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. Using the fob to be programmed, press and release both the LOCK and UNLOCK buttons, simultaneously. 9. A single chime will be heard. 10. Within four seconds of hearing the chime, press and release either the LOCK or UNLOCK button on the fob.
Page 21: Transmitter Battery Service
Transmitter Battery Service The recommended replacement battery is 2016. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal.
Page 22: To Disarm The System
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE arming. The security light in the instrument panel cluster will flash rapidly for about 15 seconds to indicate that the alarm is being set. After the alarm is set, the security light will flash at a slower rate to indicate that the system is armed.
Page 23: Sliding Rear Window-If Equipped
The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab models. The windows will operate only when the ignition switch is turned to the ON position.
Page 24: Club Cab Vented Quarter Window
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Club Cab Vented Quarter Window The Club Cab is equipped with rear quarter windows that open out. Pull the window latch toward you to unlock, and push out on the window. Press the latch straight to secure the window in an open position.
Page 25: Lap/Shoulder Belts
Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 27 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! • A belt buckled into the wrong buckle will not protect you properly.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 29: Adjustable Upper Shoulder Belt Anchorage
WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
Page 30: Front Lap Belts
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly.
Page 31: Seat Belt Extender
Seat Belt Extender If a seat belt is too short, even when fully extended, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the ex- tender and store it.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are not there to protect you. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 33 • The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column If the key is in the off position, in the ACC position, or not in the ignition, the airbags are...
Page 35 seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the...
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn On the Passenger Airbag Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch. This will turn on the passenger airbag.
Page 37 WARNING! Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically.
Page 38: Child Restraint
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: •...
Page 39 Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for the adult seat belt. Use the restraint that is correct for your child: • Safety experts recommend that rearward-facing in the vehicle until they are at least...
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE with a front shield and are held in the vehicle by the lap portion.) For further information refer to www.seatcheck.org. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision.
Page 41 • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower Anchors and Tether for CHildren. LATCH child restraint anchorage systems are installed in the Standard Cab passenger seat position, the Club Cab front passenger and rear outboard right side positions and the Quad Cab...
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Club Cab Rear Right Seat Quad Cab Rear Right Seat...
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Quad Cab Rear Left Seat NOTE: For children riding in the front seat of a Standard Cab model refer to the “Passenger Airbag On/Off Switch” located in this section. Child restraint systems having attachments designed to connect to the lower anchorages are now available.
Page 45 Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating posi- tions only.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Tether Anchor Regular Cab models have two tether anchorages, one behind each passenger seating position (front center and right seat positions). Club Cab and Quad Cab models have three anchorages, one behind each of the rear seat positions (rear left, center, and right seat positions).
Page 47 4. Remove the slack in the tether strap so that both anchor straps are pulled tight. Regular Cab With All Seats THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Tether Straps at the Front Center Seat (Regular Cab With Any Bench Seat) 1.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Remove the slack in the tether strap so that both anchor straps are pulled tight. Regular Cab With Any Bench Seat Tether Strap at the Front Passenger Seat (Club Cab) 1. Route the child restraint tether strap up and over the front passenger seat back.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Tether Straps at the Rear Passenger Seat (Club Cab and Quad Cab Rear Seats) 1. Route the child restraint tether strap through the anchor strap inner loop (loop with metal ring attached), located directly behind the child restraint.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraint Installation Sequence 1. Thread the child restraint tether strap hook through the inner loop, located directly behind the child restraint. 2. After following step 1 for either of the two outer seats, route the tether strap hook to the metal ring on the inner loop behind the center seat and attach the hook to the metal ring.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Multiple Child Restraint...
Page 52: Engine Break-In Recommendations
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 53: Safety Tips
A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. SAFETY TIPS Exhaust System WARNING! Exhaust gases contain carbon monoxide, an ex- tremely toxic gas that by itself is colorless and odorless.
Page 54: Safety Checks You Should Make Inside The Vehicle
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.).
Page 55 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......58 Inside Day/Night Mirror ....58 Automatic Dimming Mirror—...
Page 56 56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) ..69 Lights-On Reminder ....69 Fog Lights —...
Page 57 Manual Compass Calibration ....80 Outside Temperature ....81 Garage Door Opener ....81 Programming Homelink .
Page 58: 58 Understanding The Features Of Your Vehicle
58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck).
Page 59: Automatic Dimming Mirror- If Equipped
Automatic Dimming Mirror— If Equipped This mirror will automatically adjust for annoying head- light glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
Page 60: Electric Remote-Control Mirrors
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror.
Page 61: Heated Mirrors - If Equipped
WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror.
Page 62: Reclining Seats
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 63: Way Power Seat Adjuster - Driver's Side Only
6 - Way Power Seat Adjuster — Driver’s Side Only The 6-way power seat adjuster switch is on the outboard side of the driver’s seat. Use this switch to move the seat up or down, forward or rearward, recline or tilt. Lumbar Support Adjustment —...
Page 64: Seatback Releases-Bucket And Split Bench
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seatback Releases—Bucket And Split Bench Both seats have a position latch release. To release the seatback if you are on the outside of the vehicle, lift up on the recliner lever located on the outboard side of the seat. From the rear seat, lift the lever located on the rear of the seatback.
Page 65: Club Cab/Quad Cab Rear Seat
WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 66: To Open And Close The Hood
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Second, locate the hood safety latch lever between the front grille openings to the left of center.
Page 67: Lights
WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. LIGHTS UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating...
Page 68: Battery Saver
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE also known as the Party mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer).
Page 69: Daytime Running Lights (Canada Only)
Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.
Page 70: Cargo Light - If Equipped
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when the switch is pressed in, when the headlight switch is rotated to the OFF position or the high beam is selected. CARGO Light — If Equipped The cargo lights are turned on by rotating the dimmer control to the optional fully upward position.
Page 71: High Beam / Low Beam Select Switch
High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam. Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
Page 72: Windshield Washers
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
Page 73: Tilt Steering Column - If Equipped
previously selected. If the knob is pushed while in the OFF position, the wiper will wipe approximately three wipes, after the wash knob is released. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.
Page 74: Electronic Speed Control - If Equipped
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at speeds greater than 35 mph (56 km/h). The controls are mounted on the steering wheel. To Activate Push the ON/OFF button to the ON position.
Page 75: To Resume Speed
To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above 50 km/h (30 mph). To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button.
Page 76: Overhead Console
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 77: Compass/Temperature Mini-Trip Computer
COMPASS/TEMPERATURE MINI-TRIP COMPUTER This feature allows you to choose between a compass/ temperature display and one of five trip conditions being monitored. US/M Button Use this button to change the display from U.S. to metric measurement units. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 RESET Button Use this button to reset the following displays to zero: Average Fuel Economy...
Page 78: Step Button
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Step Button Use this button to choose or cycle through the four trip conditions. Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Distance To Empty (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank.
Page 79: C/T Button
C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. Compass/Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing.
Page 80: Manual Compass Calibration
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration If the compass appears erratic and the CAL light does not appear, you must calibrate the compass. Find an open area away from large metal objects. With the ignition ON and the compass/temperature displayed, press and hold the RESET button until the CAL symbol appears (about 10 seconds).
Page 81: Outside Temperature
Outside Temperature Because engine temperature can increase the displayed temperature, temperature readings are slowly updated when vehicle speed is below 20 mph (30 km/h). GARAGE DOOR OPENER The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting.
Page 82: Programming Homelink
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 83 WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
Page 84: Canadian Programming/Gate Programming
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Program- ming steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener).
Page 85: Using Homelink
3. Continue to press and hold the HomeLink button while you press and release every two seconds ( cycle ) your hand-held transmitter until the frequency signal has successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.) Proceed with Programming step four to complete.
Page 86: Electrical Power Outlets - If Equipped
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undes- ired operation.
Page 87: Electrical Outlet Use With Engine Off
automatically when ready for use. To preserve the heat- ing element, do not hold the lighter in the heating position. All accessories connected to this outlet should be re- moved or turned OFF when the vehicle is not in use to protect the battery against discharge.
Page 88: Floor Console - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FLOOR CONSOLE — IF EQUIPPED Floor Console Features The Floor Console, available with bucket seats, has the following features: • Miscellaneous storage compartments • Adjustable cup holders - with Automatic Transmission only • Portable phone storage bin •...
Page 89: Center Storage Compartment - If Equipped
storage bin can be used when ease access to the phone is needed. Also the power outlet inside console compart- ment can be used to power up the phone while it is being stored in the bin. To use plug in the portable power recharge cord and place the cord along the slot provided in the left side of the console.
Page 90: Tailgate
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When using your Quad Cab rear seat cup holder make sure that you pull the cup holder out fully to engage the cup holder arms. TAILGATE To simplify mounting of a camper unit with an overhang, the tailgate can be removed quickly.
Page 91: General Information
General Information The Manufacturer’s Warranty does not apply to body modifications and special equipment, such as a camper unit, heaters, stoves, refrigerators, etc., supplied by manufacturers other than the manufacturer. For warranty coverage and service on these items, contact the appli- cable manufacturer.
Page 93 INSTRUMENT PANEL AND CONTROLS CONTENTS Instruments And Controls ....96 Four Gauge Instrument Cluster ... . .97 Six Gauge Instrument Cluster .
Page 94 94 INSTRUMENT PANEL AND CONTROLS Fast Forward (FF) ..... 109 Rewind (RW) ......109 Tape Eject .
Page 95 Seek ......120 Tune ......120 To Set The Push-Button Memory .
Page 96: 96 Instrument Panel And Controls
96 INSTRUMENT PANEL AND CONTROLS INSTRUMENTS AND CONTROLS...
Page 97: Four Gauge Instrument Cluster
INSTRUMENT PANEL AND CONTROLS 97 FOUR GAUGE INSTRUMENT CLUSTER...
Page 98: Six Gauge Instrument Cluster
98 INSTRUMENT PANEL AND CONTROLS SIX GAUGE INSTRUMENT CLUSTER...
Page 99: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Engine Coolant Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is oper- ating satisfactorily. The gage needle in V6 and V8 engines will likely indicate a high temperature when driving in hot weather, up mountain grades, in heavy traffic, or when towing a trailer.
Page 100 100 INSTRUMENT PANEL AND CONTROLS direction of the turn. These indicators also indicate proper operation of the front and rear turn signal lights. If either indicator flashes at a faster rate than normal, check for a defective bulb. If either indicator fails to light up when the lever is moved, check for a defective fuse or turn signal bulb.
Page 101 12. Seat Belt Reminder Light This light comes on for several seconds after the ignition is turned ON as a reminder to “buckle up.” This light will remain on as long as the seat belt remains unbuckled. If this light flashes, it indi- cates a fault in the airbag system.
Page 102 102 INSTRUMENT PANEL AND CONTROLS Temperature gages may not show accurate readings. When the engine is not running, turn the ignition switch to ON to obtain accurate readings. 17. Airbag Indicator The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned ON.
Page 103 23. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and en- gine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
Page 104 104 INSTRUMENT PANEL AND CONTROLS U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined.
Page 105: Electronic Digital Clock
29. Engine Oil Pressure Indicator Light (Clusters Without A Gauge) This light indicates that the engine oil pressure has become too low. For a bulb check, this light will come on momentarily when the ignition is turned On. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
Page 106: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls - If Equipped
106 INSTRUMENT PANEL AND CONTROLS SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS — IF EQUIPPED Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 107 Toggle the PTY button to select the following format types: Program Type Radio Display Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty...
Page 108: Balance
108 INSTRUMENT PANEL AND CONTROLS Pressing PTY, then SCAN will scan the FM Band and stop at all RDS stations. Each RDS station will be played for a 5 second scan once around the FM Band and stop at the last station.
Page 109: To Change From Clock To Radio Mode
5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
Page 110: Tape Eject
110 INSTRUMENT PANEL AND CONTROLS Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button.
Page 111: Inserting The Compact Disc
CAUTION! This CD player will accept 4 ⁄ inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD. Gently insert one CD into the CD player with the CD label facing up.
Page 112: Ff/Tune/Rw
112 INSTRUMENT PANEL AND CONTROLS FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.
Page 113: Cd Changer Control Capability - If Equipped
CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.
Page 114: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
114 INSTRUMENT PANEL AND CONTROLS • Disc inserted upside down • Damaged disc • Water condensation on optics SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume.
Page 115 Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The Fade control provides for balance between the front and rear speakers. Press the FADE button in and it will pop out.
Page 116: Cd Player Operation
116 INSTRUMENT PANEL AND CONTROLS General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
Page 117: Cd Changer Control Capability - If Equipped
beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal.
Page 118 118 INSTRUMENT PANEL AND CONTROLS Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played.
Page 119: Radio Display Messages
Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player. INSTRUMENT PANEL AND CONTROLS 119 SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY Operating Instructions NOTE: Power to operate the radio is supplied through the ignition switch.
Page 120: Power Button
120 INSTRUMENT PANEL AND CONTROLS Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OFF. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
Page 121: Balance
stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Balance The balance control adjusts the left-to-right speaker bal- ance.
Page 122: Cd Changer Control Capability - If Equipped
122 INSTRUMENT PANEL AND CONTROLS Music Search Pressing the SEEK button while playing a tape will start the Music Search mode. Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection, or return to the beginning of the previous selection if the tape is within the first 5 seconds of the current selection.
Page 123 Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played.
Page 124: Radio Display Messages
124 INSTRUMENT PANEL AND CONTROLS Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player. SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on.
Page 125 Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received. To select Sirius Satellite Radio™ (if equipped), press the MODE button until the word SIRIUS appears.
Page 126: Cd Player Operation
126 INSTRUMENT PANEL AND CONTROLS To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET RND button. SET 1 will show in the display window. Select the “1–6”...
Page 127 Inserting The Compact Disc CAUTION! This CD player will accept 4 ⁄ inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 128 128 INSTRUMENT PANEL AND CONTROLS The disc can be ejected with the radio and ignition OFF. Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
Page 129 Program Type Radio Display Emergency ALERT! Emergency Test Test Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft...
Page 130: Remote Sound System Controls - If Equipped
130 INSTRUMENT PANEL AND CONTROLS REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push button in the center.
Page 131: Tape Player
Tape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection.
Page 132: Compact Disc Maintenance
132 INSTRUMENT PANEL AND CONTROLS other adverse condition is low or “muddy” sound from one or both channels, as if the treble tone control were turned all the way down. To prevent this, you should periodically clean the head with a commercially available WET cleaning cassette.
Page 133: Climate Controls
CLIMATE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. Heater Only The mode control (located at the right of the control panel) can be set in any of the following positions: NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between...
Page 134: Air Conditioning
134 INSTRUMENT PANEL AND CONTROLS Blower Control The rotary knob at the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air.
Page 135 Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located at the right of the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on.
Page 136 136 INSTRUMENT PANEL AND CONTROLS Panel Outside air flows through the outlets located in the instrument panel. Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Floor Outside air flows primarily through the floor out- lets located under the instrument panel.
Page 137: Operating Tips
Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel. These are air exhausters that provide the means for regular exchange of cab air. Side window demisters direct air flow specifically to the window glass to help prevent interior fogging of the glass.
Page 138 138 INSTRUMENT PANEL AND CONTROLS speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows.
Page 139: Operation Tips Chart
INSTRUMENT PANEL AND CONTROLS 139 Operation Tips Chart...
Page 140: Rear Window Defroster - Quad-Cab Only
140 INSTRUMENT PANEL AND CONTROLS REAR WINDOW DEFROSTER – Quad-Cab Only CAUTION! Use care when washing the inside of the rear win- dow to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements.
Page 141 STARTING AND OPERATING CONTENTS Starting Procedures ....144 Manual Transmission ....144 Automatic Transmission .
Page 142 142 STARTING AND OPERATING Tire Markings ......167 Tire Identification Number (TIN) ..171 Tire Loading And Tire Pressure .
Page 143 Snowplow ......201 Dodge Dakota Models ....201 Recreational Towing (Behind Motorhome, Etc.)
Page 144: 144 Starting And Operating
144 STARTING AND OPERATING STARTING PROCEDURES The starter should not be operated for more than 15 second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Manual Transmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depress clutch pedal to the floor before starting the vehicle.
Page 145 If Engine Fails To Start If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded.
Page 146: Engine Block Heater - If Equipped
146 STARTING AND OPERATING CAUTION! Long periods of engine idling can cause excessive exhaust temperatures which can damage your ve- hicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave children or animals inside parked vehicles in hot weather.
Page 147 switch is in the ON position. Always depress the brake pedal first, before moving the gear selector out of PARK. Gear Ranges DO NOT race the engine when shifting from Park or Neutral position into another gear range. “P” Park This position supplements parking brake by locking the transmission.
Page 148 148 STARTING AND OPERATING “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. “D” Drive Use this position for most city and highway driving. “2”...
Page 149 The “O/D OFF” feature must be selected, if desired, each time the engine is started. NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Over- drive and will automatically select the most desirable gear for operation at this temperature.
Page 150: Manual Transmission
150 STARTING AND OPERATING the vehicle speed drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages. The feature is operational in Over- drive and in Drive. NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1-3 miles (1.6 - 4.8 km) of driving].
Page 151: Four-Wheel Drive Operation
To shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear train to spin down. Move the shift lever from the Neutral position straight across and back into Reverse. Never drive with your foot resting on the clutch pedal. Do not attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnor- mal wear on the clutch.
Page 152 152 STARTING AND OPERATING When additional traction is required, the transfer case 4HI and 4LO positions can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by rotating the 4WD Control Switch to the desired position - see Shifting Procedure section for specific shifting instructions.
Page 153 seconds, and retry selection. To find the shift require- ments, refer to the Shifting Procedure for your transfer case, located in this section of the owner’s manual. The “SERVICE 4WD” warning light monitors the electric shift 4WD system. If this light remains on after engine start up or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required.
Page 154 154 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
Page 155: Shifting Procedure - Nv233 Transfer Case
Shifting Procedure - NV233 Transfer Case NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
Page 156 156 STARTING AND OPERATING 4HI to 4LO or 4LO to 4HI NOTE: When shifting into or out of 4LO some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants. Shifting can be performed with the vehicle rolling 2-3 mph (3-5 km/h) or completely stopped.
Page 157: Nv244 Transfer Case Operating Information / Precautions
NV244 Transfer Case Operating Information / Precautions The NV244 is an electric shift transfer case and is operated by the 4WD Control Switch, which is located on the instrument panel. The NV244 transfer case provides 4 mode positions - Normal all wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral.
Page 158 158 STARTING AND OPERATING case selection. When you select a different transfer case position, the indicator lights will do the following: If All Shift Requirements are Met 1. The current position indicator light will turn OFF. 2. The selected position indicator light will flash until the transfer case completes the shift.
Page 159 shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case. When operating your vehicle in 4LO, the engine speed is approximately three times that of the AWD or 4HI positions at a given road speed.
Page 160: Shifting Procedure - Nv244 Transfer Case
160 STARTING AND OPERATING 4 Wheel Drive High Range - Locks the transfer case inter-axle differential. Forces front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. 4 Wheel Drive Low Range - Low speed 4 wheel drive. Locks the transfer case inter-axle differential.
Page 161 AWD to 4HI or 4HI to AWD Rotate the 4WD Control Switch to the desired position. Shifts between AWD and 4HI can be done with the vehicle stopped or in motion. With the vehicle in motion, the transfer case will engage / disengage faster if you momentarily release the accelerator pedal after turning the control switch.
Page 162: Limited-Slip Differential - If Equipped
162 STARTING AND OPERATING Alternate Procedure 1. Bring the vehicle to complete stop. 2. With the key ON and the engine either OFF or RUNNING, shift the transmission into NEUTRAL (de- press clutch on manual transmissions). 3. Rotate the transfer case control switch to the desired position.
Page 163: Parking Brake
PARKING BRAKE The parking brake should be applied whenever the driver is not in the vehicle. The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the parking brake: Place your foot on the parking brake pedal and push firmly downward as far as the pedal will go.
Page 164: Brake System
164 STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or vehicle may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual trans- mission in Reverse or first gear. Failure to do so may cause the vehicle to roll and cause damage or injury.
Page 165: Four-Wheel Anti-Lock Brake System - If Equipped
During severe braking conditions, particularly with changing road surfaces, such as ice to concrete, a slight drop or minor pulsation may be felt in the brake pedal. WARNING! Both Anti-Lock Brake Systems contain sophisticated electronic equipment. It may be susceptible to inter- ference caused by improperly installed or high out- put radio transmitting equipment.
Page 166: Power Steering
166 STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
Page 167: Rocking The Vehicle
ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. The least amount of accelerator pedal pressure to main- tain the rocking motion without spinning the wheels or racing the engine is most effective.
Page 168 168 STARTING AND OPERATING NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 169 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 170 170 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 171: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 172: Tire Loading And Tire Pressure
172 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. Tire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle...
Page 173 adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual. NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWR’s) for the front and rear axles must not be exceeded.
Page 174 174 STARTING AND OPERATING NOTE: For the following example the combined weight of occupants and cargo should never exceed 865 lbs. (392 Kg).
Page 175: Tires-General Information
WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 176: Tire Inflation Pressures
176 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 177 CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 178: Radial-Ply Tires
178 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Page 179: Tire Spinning
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...
Page 180: Tread Wear Indicators
180 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 181: Alignment And Balance
WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Page 182: Supplemental Tire Pressure Information
182 STARTING AND OPERATING SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on a “Supplemental Tire Pressure Inflation” label located on the face of the driver’s door or in the Tire Information Pressures pamphlet in the glove box.
Page 183: Snow Tires
SNOW TIRES Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
Page 184: Fuel Requirements
184 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 185: Gasoline/Oxygenate Blends
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE and ETBE. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle.
Page 186: Materials Added To Fuel
186 STARTING AND OPERATING sulfur to determine if the problem is fuel related prior to returning your vehicle to an authorized dealer for ser- vice. CAUTION! If the Check Engine or Service Engine Soon light is flashing, immediate service is required; see onboard diagnostics system section.
Page 187: Fuel Tank Filler Tube
WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive.
Page 188: Fuel System Cautions
188 STARTING AND OPERATING WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: •...
Page 189: Carbon Monoxide Warnings
Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 190 190 STARTING AND OPERATING CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and...
Page 191: Vehicle Loading
VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN).
Page 192: Curb Weight
192 STARTING AND OPERATING Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle’s GVWR. Tire Size This is the minimum allowable tire size for your vehicle. Replacement tires must be equal to the load capacity of this tire size.
Page 193 WARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle.
Page 194: Loading Wide Building Materials
194 STARTING AND OPERATING LOADING WIDE BUILDING MATERIALS Four foot wide building materials can be conveniently carried in the Dakota pickup box. For occasional use up to 600 lbs (272 kg) of unrestrained material [9 pcs. 3/4 (19 mm) plywood] can be supported on 2 X 6 lumber placed crossbody in indentations provided in the pickup box inner walls.
Page 195: Trailer Towing
See your dealer or a reputable installer of aftermarket equipment for further information on the installation of these supports. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 196 196 STARTING AND OPERATING tongue that typically provides adjustable friction associ- ated with the telescoping motion to dampen any un- wanted trailer swaying motions while traveling. CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle.
Page 197: Trailer And Tongue Weight
Wheel style trailer, this range of loading on the King Pin should be between 15% and 25%.) Loads balanced over the wheels or biased toward heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
Page 198: Trailer Towing-Hitches
198 STARTING AND OPERATING to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle. Trailer sway control and equalizing hitch are required for tongue weights above 350 lbs. (159 kg). Trailer Towing—Hitches: With a Class I Hitch, your vehicle can be equipped to tow trailers with a Gross Trailer Weight (GTW) of 2,000 lbs.
Page 199: Trailer Towing Information (Maximum Trailer Weight Ratings)
In Canada, refer to the following website address: http:// www.dodge.ca. Trailer Towing Requirements All Dodge Dakota trucks are intended to tow trailers up to 2,000 lbs. without added equipment or alterations to standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs.
Page 200: Trailer Tow Wiring
200 STARTING AND OPERATING of the trailer lights and assure their proper functioning, a heavy duty turn signal flasher can be installed as a separate equipment item by your dealer. WARNING! The direct connection of hydraulic brake lines from vehicle brake system to trailer system is not accept- able.
Page 201: Cooling System Tips-Trailer Towing
Maintenance Schedule “B”. STARTING AND OPERATING 201 SNOWPLOW Dodge Dakota Models NOTE: Do not use Dodge Dakota Models for snow- plow applications. WARNING! Snowplows, winches, and other aftermarket equip- ment should not be added to the front end or your vehicle.
Page 202: Recreational Towing (Behind Motorhome, Etc.) Of 4X4 Vehicles
202 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) OF 4X4 VEHICLES CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: Both the NV233 and NV244 transfer cases must be shifted into Neutral (N) for recreational towing.
Page 203 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 4 seconds. 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9.
Page 204: Returning To Normal Operation
204 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P).
Page 205 NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no position indicator lights will be on or flashing. NOTE: Flashing neutral (N) position indicator light indicates that shift requirements have not been met.
Page 206: Traction
206 STARTING AND OPERATING TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 207 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....208 Adding Fuel ......208 Changing A Flat Tire .
Page 208: Hazard Warning Flasher
208 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers.
Page 209: Changing A Flat Tire
WARNING! Remove the gas cap slowly to prevent fuel spray from the filler neck which may cause injury. The volatility of present gasolines may cause a build up of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when you remove the cap from a hot vehicle.
Page 210: Jack Removal And Stowage
210 WHAT TO DO IN EMERGENCIES • In the Club Cab the jack and tools are stowed in a floor compartment located under the rear seat on the pas- senger’s side of the vehicle. The seat cushion can be lifted to a vertical position to allow access to this compartment.
Page 211: What To Do In Emergencies 211
handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel.
Page 212 212 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. •...
Page 213 Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 5. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WHAT TO DO IN EMERGENCIES 213 WARNING! Raising the vehicle higher than necessary can make...
Page 214 214 WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. 8.
Page 215: Jump Starting
To Stow The Flat Or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle.
Page 216 216 WHAT TO DO IN EMERGENCIES If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1. Wear eye protection and remove all metal jewelry such as watch bands or bracelets which might make an unintended electrical contact.
Page 217: Towing A Disabled Vehicle
WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode.
Page 218: Four-Wheel Drive Vehicles
218 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Vehicles The manufacturer recommends towing with all wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. Two-Wheel Drive Vehicles Provided that the transmission is operable, tow with the transmission in Neutral and the ignition key in the OFF...
Page 219: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment 3.7L V6 ... . . 221 Engine Compartment 4.7L V-8 ... . 222 Onboard Diagnostic System — OBD II ..223 Emissions Inspection And Maintenance Programs .
Page 220 220 MAINTAINING YOUR VEHICLE Windshield Wiper Blades ....235 Windshield Washers ....236 Exhaust System .
Page 221: Engine Compartment 3.7L V6
MAINTAINING YOUR VEHICLE 221 ENGINE COMPARTMENT 3.7L V6...
Page 222: Engine Compartment 4.7L V-8
222 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 4.7L V-8...
Page 223: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 224: Emissions Inspection And Maintenance Programs
224 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running,...
Page 225: Replacement Parts
serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
Page 226: Maintenance Procedures
226 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
Page 227: Maintenance Schedules
CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could dam- age your engine. Frequency Of Oil Change Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: •...
Page 228 228 MAINTAINING YOUR VEHICLE Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner and the crankcase inlet air cleaner. The crankcase ventilation system should also be checked periodically.
Page 229: Engine Oil Filter
• Lubricants which do not have both the engine oil certification mark or current service symbol and the correct viscosity grade number should not be used. 3.7L/4.7L Engines Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic.
Page 230: Drive Belts - Check Condition And Tension
230 MAINTAINING YOUR VEHICLE quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are a high quality oil filter and are recommended. Drive Belts — Check Condition and Tension At the mileage indicated in the maintenance schedule, all belts should be checked for condition and proper tension.
Page 231: Engine Fuel Filter
WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed.
Page 232: Maintenance-Free Battery
Maintenance-Free Battery All Dodge trucks are equipped with maintenance-free batteries. You will never have to add water, nor is periodic maintenance required.
Page 233: Air Conditioner Maintenance
WARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery. To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration.
Page 234: Power Steering - Fluid Check
234 MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. •...
Page 235: Front Suspension Ball Joints
Front Suspension Ball Joints The ball joints and seals should be inspected whenever the vehicle is serviced for other reasons. Damaged seals should be replaced to prevent leakage or contamination of the grease. Steering Linkage Whenever the vehicle is hoisted, all steering linkage joints should be inspected for evidence of damage.
Page 236: Windshield Washers
236 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield.
Page 237: Cooling System
Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
Page 238 238 MAINTAINING YOUR VEHICLE WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood don’t open the hood until the radiator has had time to cool. If you open the hood and see steam or hot coolant escaping from the radiator, don’t touch anything.
Page 239 CAUTION! Mixing of coolants other than specified (non- HOAT), may result in engine damage that may not be covered under the new vehicle warranty, and decreased corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 240 240 MAINTAINING YOUR VEHICLE Coolant Pressure Cap The coolant pressure cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant reserve tank. The pressure cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
Page 241: Emission Related Components
The radiator normally remains completely full, so there is no need to remove the pressure cap except when check- ing coolant freeze point or when replacing coolant. Your service attendant should be advised of this. When addi- tional coolant is needed to maintain the proper level, it should be added to the overflow bottle.
Page 242 242 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. NOTE: Fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings.
Page 243: Brake System
Brake System Power Disc Brakes (Front) Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Self-Adjusting Rear Brakes To maintain the correct adjustment, you need only drive your vehicle in reverse and apply the brakes.
Page 244 244 MAINTAINING YOUR VEHICLE WARNING! Use of brake fluid that may have a lower initial boiling point, or is unidentified as to specifications, may result in sudden brake failure during hard prolonged braking. You could have an accident. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
Page 245: Clutch Hydraulic System
WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance free system.
Page 246 246 MAINTAINING YOUR VEHICLE 3. Fully apply the parking brake and press the brake pedal. 4. Place the gear selector momentarily in each gear position ending with the lever in P (Park). 5. Remove the dipstick, wipe it clean and reinsert it until seated.
Page 247 Authorized Dodge Dealer or Service Center. It is important that the transmission be adjusted periodically, the fluid be main- tained at the correct level, and that it be drained and refilled as specified.
Page 248: Transfer Case
248 MAINTAINING YOUR VEHICLE Transfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level can be checked by removing the filler plug located on the back side of the transfer case. The fluid level should be at the bottom edge of the filler plug hole when the vehicle is in a level position.
Page 249: Appearance Care And Protection From Corrosion
There are two groups identified, those for wheel bearings (Letter “G”) and those for chassis (Letter “L”) lubrication. Perfor- mance categories within these groups result in dual letter each group. The letter des- ignations shown in the ex- ample are the highest quality level available and when combined as shown can be used for chassis lubrication.
Page 250 250 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible.
Page 251 recommended. Do not use oven cleaner. Avoid auto- matic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective fin- ish. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed.
Page 252: Power Distribution Center
252 MAINTAINING YOUR VEHICLE defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instru- ments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.
Page 253: Fuse Block
This power center houses plug-in cartridge and relays. A label inside the latching cover of the center identifies each component for ease of replacement, if necessary. Car- tridge fuses and relays can be obtained from your Dodge dealer. FUSE BLOCK The fuse block contains blade-type mini-fuses, relays, and circuit breakers for high-current circuits.
Page 254: Vehicle Storage
254 MAINTAINING YOUR VEHICLE NOTE: If you are leaving your vehicle dormant for longer than 21 days, you may want to take steps to protect your battery. You may do this by disconnecting the battery or by disconnecting the ignition-off draw (I.O.D.) fuse in cavity #12.
Page 255: Bulb Replacement
LIGHT BULBS — Outside Headlight ......9007LL Back-Up ......3157 Center High Mounted Stoplight .
Page 256: Parking/Turn Signal Lights
256 MAINTAINING YOUR VEHICLE 4. Remove the bolts attaching the headlamp to the inner fender panel. 5. Grasp the headlamp and pull firmly to disengage it from the panel. 6. Disconnect all connectors and separate the headlamp module from the vehicle 7.
Page 257: License Lights
2. Rotate the bulb and socket assembly 1/4 turn and pull it from housing. 3. The bulb can be removed from the sockets by pulling it straight out. License Lights 1. Rotate the socket 1/4 turn counterclockwise. 2. Pull the bulb from socket. MAINTAINING YOUR VEHICLE 257 Center High-Mounted Stoplight 1.
Page 258: Fluids And Capacities
258 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel Regular/Club Cab, 87 Octane Quad Cab, 87 Octane Engine Oil (with filter) 3.7L, SAE 5W-30, API Certified 4.7L, SAE 5W-30, API Certified Cooling System 3.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) U.S.
Page 259: Recommended Fluids, Lubricants And Genuine Parts
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) P/N 5011764AB or equivalent. Engine Oil Use SAE 5W-30, API Certified, meeting material standard MS-6395. Engine Oil Filter Mopar Engine Oil Filter, P/N 5281090 or equivalent.
Page 260: Chassis
260 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Manual Transmission (NV 3500) Transfer Case Front and Rear Axles Rear Axle Fluid for Trailer Towing Brake Master Cylinder Power Steering Reservoir Steering Linkage Ball Joints Fluids, Lubricants and Genuine Parts. Mopar ATF+4, Automatic Transmission Fluid. Mopar Manual Transmission Fluid, part number 4874464 Mopar ATF+4, Automatic Transmission Fluid.
Page 261 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..262 Emissions Testing ..... . 262 Maintenance Schedules ....263 Schedule “B”...
Page 262: Emission Control System Maintenance
262 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper func- tioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 263: Maintenance Schedules
MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. •...
Page 264 264 MAINTENANCE SCHEDULES CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 265: Schedule "B
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F ( 0° C). • Stop and go driving. • Extensive engine idling. •...
Page 266 266 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. 3,000 6,000 9,000 (5 000) (10 000) (14 000) 12,000 15,000...
Page 267 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Drain and refill automatic transmission fluid and change main sump filter (4.7L).
Page 268 268 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. 33,000 36,000 39, 000 (53 000) (58 000) (62 000) 42,000 45,000...
Page 269 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if re- quired.
Page 270 270 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Inspect auto tension drive belt, replace if required. 63,000 66,000 69,000...
Page 271 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if re- quired.
Page 272 272 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Flush and replace engine coolant. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. 93,000 96,000 99,000 (149 000) (154 000) (158 000) 100,000 102,000 (160 000) (163 000)
Page 273 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if required.
Page 274: 274 Schedule "A
274 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Check transfer case fluid level (4X4). Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. 6,000 12,000 18,000 (10 000) (19 000) (29 000) [12] [18] 24,000...
Page 275 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Flush and replace engine coolant at 60 months, regardless of mileage. Check transfer case fluid level (4X4). Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if required.
Page 276 276 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Check transfer case fluid Level (4X4). Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.* Inspect auto tension drive belt and replace if required.‡...
Page 277 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Drain and refill transfer case fluid (4X4). Flush and replace engine coolant, if not done at 60 mos. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace if necessary.* Inspect auto tension drive belt and replace if required.‡...
Page 279: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......280 Prepare For The Appointment .
Page 280 280 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 281 This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
Page 282 282 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts.
Page 283 IF YOU NEED CONSUMER ASSISTANCE 283...
Page 284 284 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra-...
Page 285 • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts.
Page 287 INDEX...
Page 288 288 INDEX Adding Engine Coolant (Antifreeze) ..239 Adding Fuel ......186,208 Air Conditioner Maintenance .
Page 289 Brake Fluid ......260 Brake System ..... . . 164,243 Anti-Lock .
Page 290 290 INDEX Compact Disc Maintenance ....132 Compact Disc Player ....106,110 Compact Spare Tire .
Page 291 Downshifting ......151 Drive Belts ......230 Drive Shaft Universal Joints .
Page 292 292 INDEX Turn Signal ......99 Flat Tire Stowage ..... . . 215 Flooded Engine Starting .
Page 293 Headlights ......255 Dimmer Switch ..... . . 100 High Beam .
Page 294 294 INDEX Lap/Shoulder Belts ..... . 25 LATCH (Lower Anchors and Tether for CHildren) ..42 Lead Free Gasoline ..... . 184 Lights .
Page 295 Power Door ......14 Lower Anchors and Tether for CHildren (LATCH) ......42 Lubricating Oil .
Page 296 296 INDEX Viscosity ......228,258 Onboard Diagnostic System ... . 223,224 Opener, Garage Door .
Page 297 Shifting out of Transfer Case Neutral (N) Reformulated Gasoline ....184 Refrigerant ......234 Release, Hood .
Page 298 298 INDEX Transfer Case ......151 Transfer Case, Shifting into Transfer Case Neutral (N) ....202 Transfer Case, Shifting out of Transfer Case Neutral (N) .
Page 299 Tires ......54,175 Air Pressure ......175 Alignment .
Page 300 300 INDEX Transmitter Battery Service ....21 Transmitter, Garage Door Opener ... . 81 Transmitter Programming ....19 Tread Wear Indicators .

This manual is also suitable for:

2004 dakota Dakota

Dodge 2004 AN Dakota Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Instrument Panel and Controls

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Dodge 2004 AN Dakota

Summary of Contents for Dodge 2004 AN Dakota