Page 1
Dakota 2 0 1 1 O W N E R ’ S M A N U A L...
Page 2
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Chrysler Group LLC shall be deemed to be deleted and features and equipment that are either standard or op- the name Chrysler Canada Inc.
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a accident resulting in serious injury or death.
Page 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Sentry Key — If Equipped ....15 ▫...
Page 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Keyless Entry (RKE) ....20 Windows ......33 ▫...
Page 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belt Pretensioners ....48 ▫ Event Data Recorder (EDR) ....62 ▫...
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your vehicle has the Automatic Transmission key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized 1.
Page 15
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 key to the right slightly, then remove the key as de- scribed. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
Page 16
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. Manual Transmission — If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Locking Doors With A Key To Release The Steering Wheel Lock You can insert the key into the door lock cylinder with Insert the key in the ignition switch and start the engine. either side up.
Page 18
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system uses ignition keys that have an embedded If the Vehicle Security Light turns on during normal electronic chip (transponder) to prevent unauthorized vehicle operation (vehicle running for longer than 10 sec- vehicle operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Replacement Keys procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one NOTE: Only keys that are programmed to the vehicle that has never been programmed. electronics can be used to start and operate the vehicle.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Insert the second valid key into the ignition switch. Repeat this procedure to program up to eight keys. If you Turn the ignition switch to the ON/RUN position within do not have a programmed Sentry Key , contact your 15 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Arm The System The Vehicle Security Alarm will also disarm if the vehicle The Vehicle Security Alarm will set when you use the Sentry Key in inserted into the ignition and turned to power door locks, or use the Remote Keyless Entry (RKE) ON/RUN.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY REMOTE KEYLESS ENTRY (RKE) This system allows you to lock or unlock the doors or Vehicles Equipped With Power Door Locks activate the Panic Alarm from distances up to approxi- All interior lights will illuminate in the vehicle when the mately 66 ft (20 m) using a Remote Keyless Entry (RKE) doors are unlocked using the Remote Keyless Entry...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: The line of transmission must not be blocked 3. Release both buttons at the same time. with metal objects. 4. Test the feature while outside of the vehicle by press- To Unlock The Doors ing the LOCK/UNLOCK button on the RKE transmitter.
Page 24
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Horn Chirp Programming NOTE: Pressing the LOCK button on the RKE transmit- The horn chirp feature is shipped from the assembly ter while you are inside the vehicle will activate the plant activated. If desired, this feature can be disabled by Vehicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 4. Test the Flash Lamps With Lock feature while outside To cancel the Panic mode, press and release the PANIC of the vehicle by pressing the LOCK button on the RKE button on the RKE transmitter a second time. Panic mode transmitter with the ignition in the OFF position and the will automatically cancel after three minutes, or if the key removed.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your RKE transmitter fails to operate from a normal 1. If the RKE transmitter is equipped with a screw, distance, check for these two conditions: remove the screw. With the RKE transmitter buttons facing down, use a flat blade to pry the two halves of the 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Remove and replace the battery. When replacing the NOTE: The vehicle must be equipped with an auto- battery, match the + sign on battery to the + sign on the matic transmission to be equipped with Remote Start. inside of the battery clip, located on the back cover.
Page 28
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WARNING! • The park lamps will turn on and remain on during • Do not start or run an engine in a closed garage or Remote Start mode. confined area. Exhaust gas contains Carbon Mon- •...
Page 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • The transmission is moved out of PARK To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release • The brake pedal is pressed the UNLOCK button on the RKE transmitter to unlock To Exit Remote Start Mode Without Driving The the doors and disarm the Vehicle Security Alarm (if...
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks • For personal security and safety in the event of an All the doors can be manually locked from the inside by accident, lock the vehicle doors as you drive, as pushing down the door lock knob, located on the door trim well as when you park and leave the vehicle.
Page 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 chime will sound if the key is in the ignition switch and the driver’s door is open, as a reminder to remove the key. Automatic Door Locks — If Equipped The doors will lock automatically if all of the following conditions are met: 1.
Page 32
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks Programming — If 2. Within 15 seconds, cycle the ignition switch between Equipped LOCK and ON/RUN and then back to LOCK four times The Automatic Door Locks feature can be enabled or ending up in the LOCK position (do not start the engine).
Page 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Auto Unlock On Exit Feature — If Equipped 4. Within 15 seconds, cycle the key from the LOCK This feature unlocks all of the doors of the vehicle when position to the ON/RUN position and back to LOCK any door is opened.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child-Protection Door Lock To use the system, open each rear door, slide the lever up To provide a safer environment for children riding in the to engage the locks, and down to disengage the child- rear seat, the rear doors of your vehicle have the child- protection locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 There is a single opening and closing switch on the WARNING! passenger doors for passenger window control. The Avoid trapping anyone in a vehicle in a collision. windows will operate when the ignition switch is turned Remember that the rear doors can only be opened to the ON/RUN or ACC position, and for ten minutes from the outside when the Child-Protection locks are...
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch WARNING! The Window Lockout Switch on the driver’s door allows you to disable the window control on the other doors. To Never leave children alone in a vehicle. Leaving disable the window controls on the other doors, press the unattended children in a vehicle is dangerous for a Window Lockout button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • Supplemental Side Air Bag Inflatable Curtains Wind Buffeting Wind buffeting can be described as the perception of (SABIC) for the driver and passengers seated next to a pressure on the ears or a helicopter-type sound in the window —...
Page 38
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you will be carrying children too small for adult-sized WARNING! seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold Infants in rear facing child restraints should never infant and child restraint systems.
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 If a child from 1 to 12 years old (not in a rear facing child 5. If the air bag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact as far back as possible and use the proper child restraint.
Page 40
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even WARNING! (Continued) on short trips. Someone on the road may be a poor driver • Being too close to the steering wheel or instrument and cause an accident that includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Lap/Shoulder Belts Left Center Right All seating positions, have combination lap/shoulder First Row CRS Lock belts. The belt webbing retractor is designed to lock Second Row CRS Lock CRS Lock CRS Lock during very sudden stops or accidents.
Page 42
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. For regular occupants: Only pull the belt webbing out WARNING! (Continued) far enough to comfortably wrap around the occupant’s • Wearing a seat belt incorrectly is dangerous. Seat mid-section. If the belt is pulled fully out, allow the belt belts are designed to go around the large bones of to fully retract.
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Lap/Shoulder Belt Operating Instructions 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch 1. Enter the vehicle and close the door. Sit back and plate and pull out the belt.
Page 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! (Continued) plate into the buckle until you hear a “click.” • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the WARNING! vehicle in an accident, increasing head and neck...
Page 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up • A lap belt worn too high can increase the risk of on the shoulder belt.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the shoulder belt on your chest so that it is Adjustable Upper Shoulder Belt Anchorage comfortable and not resting on your neck. The retractor In the front and second row outboard seats, the shoulder will withdraw any slack in the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. WARNING! The folded webbing must enter the slot at the top of the • A lap belt worn too loose or too high is dangerous. latch plate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 If the passenger seating position is equipped with an position that has a belt with this feature. Children ALR and is being used for normal usage: 12 years old and under should always be properly restrained in the rear seat.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat WARNING! belt placement by the occupant. The seat belt still must be • The belt and retractor assembly must be replaced worn snugly and positioned properly. if the seat belt assembly Automatic Locking Re- The pretensioners are triggered by the Occupant Re- tractor (ALR) feature or any other seat belt func-...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 60 seconds of vehicle speed over 5 mph (8 km/h). The WARNING! reminder sequence lasts for 96 seconds or until the driver • The belt and retractor assembly must be replaced seat belt is fastened. After the sequence completes, the Seat Belt Reminder Light remains illuminated until the if the seat belt assembly Automatic Locking Re- driver seat belt is fastened.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert can be enabled or disabled by your authorized NOTE: Watch the Seat Belt reminder Light to turn on dealer, or by following these steps: while the seat belt retracts and turn off while re-buckling the seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Seat Belt Extender Bag is mounted in the center of the steering wheel. The If a seat belt is too short, even when fully extended, your passenger’s Advanced Front Air Bag is mounted in the authorized dealer can provide you with a seat belt instrument panel, above the glove compartment.
Page 54
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These air bags are certified to the new Federal This vehicle may also be equipped with Supplemental regulations for Advanced Air Bags. Side Air Bag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a win- The Advanced Front Air Bags have a multistage inflator dow.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, Air Bag System Components Your vehicle may be equipped with the following air bag and Seat Track Position Sensors system components: Advanced Front Air Bag Features •...
Page 56
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not have any accessory items installed which • No objects should be placed over or near the air bag will alter the roof, including adding a sunroof to on the instrument panel, because any such objects your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 NOTE: Air Bag covers may not be obvious in the Knee Impact Bolsters interior trim, but they will open during air bag deploy- The Knee Impact Bolsters help protect the knees of the ment.
Page 58
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC determines if deployment of the front and/or impact, Advanced Front Air Bags may deploy in crashes side air bags in a frontal or side collision is required. with little vehicle front-end damage but that produce a Based on the impact sensor’s signals, a central electronic severe initial deceleration.
Page 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 position, in the ACC position, or not in the ignition, the WARNING! air bag system is not on and the air bags will not inflate. Ignoring the Air Bag Warning Light in your instru- The ORC contains a backup power supply system that ment panel could mean you won’t have the air bags may deploy the air bags even if the battery loses power or...
Page 60
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are possible, based on the collision type and severity. The A quantity of non-toxic gas is generated to inflate the steering wheel hub trim cover and the upper right side of SABIC. The inflating SABIC pushes the outside edge of the instrument panel separate and fold out of the way as the headliner out of the way and covers the window.
Page 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Enhanced Accident Response System NOTE: Front and/or side air bags will not deploy in all In the event of an impact causing air bag deployment, if collisions. This does not mean something is wrong with the communication network remains intact, and the the air bag system.
Page 62
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE bag inflation. These airborne particles may irritate the Maintaining Your Air Bag System skin, eyes, nose, or throat. If you have skin or eye WARNING! irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air.
Page 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Air Bag Warning Light WARNING! (Continued) You will want to have the air bags ready to • Do not attempt to modify any part of your air bag inflate for your protection in a collision. The system.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Whether or not the driver and passenger safety belts NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint were buckled/fastened; Controller (ORC) may also be disabled. The air bags may •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 In addition to the vehicle manufacturer, other parties, WARNING! such as law enforcement, that have the special equip- ment, can read the information if they have access to the In a collision, an unrestrained child, even a tiny baby, vehicle or the EDR.
Page 66
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints WARNING! • Safety experts recommend that children ride Rearward-facing child seats must never be used in rearward-facing in the vehicle until they are at least the front seat of a vehicle with the front passenger air one year old and weigh at least 20 lbs (9 kg).
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • The belt-positioning booster seat is for children weigh- • Check belt fit periodically. A child’s squirming or ing more than 40 lbs (18 kg), but who are still too small slouching can move the belt out of position. to fit the vehicle’s seat belts properly.
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Standards. The manufacturer recommends that you WARNING! try a child restraint in the vehicle seats where you will • Improper installation can lead to failure of an use it before you buy it. infant or child restraint.
Page 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 belt system will loosen with time, so check the belt using the vehicle’s seat belts, instead securing the child occasionally and pull it tight, if necessary. restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure.
Page 70
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Extended Cab Crew Cab • The Extended Cab right rear (if equipped with a rear • The Crew Cab second row seat has lower anchorages seat) passenger seating position has lower anchorages that are capable of accommodating LATCH-compatible for LATCH-equipped child restraints.
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seatback, and are just visible when you lean into the vehicle to install the child restraint.
Page 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You will first loosen the child seat adjusters on the lower of reach of children. It is recommended that before straps and on the tether strap so that you can more easily installing the child restraint, buckle the seat belt so the attach the hooks or connectors to the vehicle anchorages.
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Installing Child Restraints Using The Vehicle Seat Installing a Child Restraint with a Cinching Latch Plate: Belt 1. To install a child restraint with a cinching latch plate, The passenger seat belts are equipped with cinching latch first, pull enough of the seat belt webbing from the plates to secure a Child Restraint System (CRS).
Page 74
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the belt still can’t be tightened, or if pulling and WARNING! pushing on the restraint loosens the belt, disconnect the • With a child restraint installed in the rear passen- latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again.
Page 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Tether Straps at the Rear Passenger Seat 2. Route the tether strap across to the center tether (Extended Cab) anchorage. The center tether is located behind the slide door in the center of the vehicle, between the two seating 1.
Page 76
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Straps at the Rear Passenger Seat (Crew Cab) 1. Route the child restraint tether strap under the head restraint for the outboard seating positions, and then through the anchor strap outer loop (webbing material loop), located directly behind the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the Drive moderately during the first 300 miles (500 km).
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few WARNING! (Continued) thousand miles (kilometers) of operation. This should be • It is extremely dangerous to ride in a cargo area, considered a normal part of the break-in and not inter- inside or outside of a vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Exhaust Gas If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate WARNING! control BLOWER switch is set at high speed. DO NOT use the recirculation mode.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Defroster Vehicle Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is frays, and loose parts.
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! (Continued) WARNING! (Continued) • Always make sure that floor mats are properly • Always make sure that objects cannot fall into the attached to the floor mat fasteners. driver footwell while the vehicle is moving. Ob- •...
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Outside Mirrors Power Mirrors To receive maximum benefit, adjust the outside mirror(s) The power mirror controls are located on the driver’s to center on the adjacent lane of traffic with a slight door trim panel. overlap of the view obtained on the inside mirror.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To adjust a mirror, turn the control wand toward the left WARNING! or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
Page 91
• www.chrysler.com/uconnect seven mobile phones to be linked to the system. Only one linked (or paired) mobile phone can be used with the • www.dodge.com/uconnect system at a time. The system is available in English, • www.jeep.com/uconnect Spanish, or French languages.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone Button The Uconnect™ Phone is fully integrated with the vehi- The radio or steering wheel controls (if cle’s audio system. The volume of the Uconnect™ Phone equipped) will contain the two control buttons can be adjusted either from the radio volume control (Uconnect™...
Page 93
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • For certain operations, compound commands can be Help Command used. For example, instead of saying “Setup” and then If you need assistance at any prompt, or if you want to “Pair a Device”, the following compound command know your options at any prompt, say “Help”...
Page 94
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to To complete the pairing process, you will need to refer- ence your mobile phone Owner’s Manual. The give the Uconnect™ Phone a name for your mobile Uconnect™...
Page 95
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • The system will prompt you to say the name of the Dial By Saying A Number person you want to call. • Press the button to begin. • After the “Ready” prompt and the following beep, say •...
Page 96
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say The Uconnect™ Phone will allow you to enter up to 32 “Phonebook New Entry”. names in the phonebook with each name having up to four associated phone numbers and designations.
Page 97
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the Bluetooth wireless phone connection is deleted on the Uconnect™ Phone. These can only be made to the Uconnect™...
Page 98
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Next, choose the number designation (home, work, • Press the button to begin. mobile, or other) that you wish to edit. • After the “Ready” prompt and the following beep, say • When prompted, recite the new phone number for the “Phonebook Delete”.
Page 99
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • Note that only the phonebook entry in the current List All Names In The Uconnect™ Phonebook language is deleted. • Press the button to begin. • Automatic downloaded phonebook entries cannot be •...
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features Answer Or Reject An Incoming Call — The following features can be accessed through the Call Currently In Progress Uconnect™ Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
Page 101
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Making A Second Call While Current Call Is In indicating that the active and hold status of the two calls Progress have switched. Only one call can be placed on hold at a To make a second call while you are currently on a call, time.
Page 102
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination Call Continuation To end a call in progress, momentarily press the Call continuation is the progression of a phone call on the Uconnect™ Phone after the vehicle ignition key has been button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Uconnect™ Phone Features Emergency Assistance If you are in an emergency and the mobile phone is Language Selection reachable: To change the language that the Uconnect™ Phone is • Pick up the phone and manually dial the emergency using: number for your area.
Page 104
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canada and 060 for Mexico). The number dialed may Towing Assistance not be applicable with the available mobile service and If you need towing assistance: area. • Press the button to begin. • If supported, this number may be programmable on •...
Page 105
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Paging When calling a number with your Uconnect™ Phone that To learn how to page, refer to “Working with Automated normally requires you to enter in a touch-tone sequence Systems”. Paging works properly except for pagers of on your mobile phone keypad, you can press the certain companies, which time out a little too soon to button and say the sequence you wish to enter, followed...
Page 106
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Uconnect™ Phone will then send the corresponding Turning Confirmation Prompts ON/OFF phone number associated with the phonebook entry, as Turning confirmation prompts off will stop the system tones over the phone. from confirming your choices (e.g., the Uconnect™ Phone will not repeat a phone number before you dial it).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Dialing Using The Mobile Phone Keypad Mute/Un-Mute (Mute OFF) You can dial a phone number with your mobile phone When you mute the Uconnect™ Phone, you will still be keypad and still use the Uconnect™ Phone (while dialing able to hear the conversation coming from the other via the mobile phone keypad, the user must exercise party, but the other party will not be able to hear you.
Page 108
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say “List Phones”. from your Uconnect™ Phone paired mobile phone to the Uconnect™ Phone or vice versa, press the button • The Uconnect™ Phone will play the phone names of and say “Transfer Call”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • The selected phone will be used for the next phone Things You Should Know About Your Uconnect™ call. If the selected phone is not available, the Phone Uconnect™ Phone will return to using the highest Uconnect™...
Page 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can either press the Uconnect™ Phone button to Voice Command restore the factory setting or repeat the words and • For best performance, adjust the rearview mirror to phrases when prompted by the Uconnect™ Phone. For provide at least ⁄...
Page 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • fully closed windows, • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • dry weather condition. • You can say “O” (letter “O”) for “0” (zero). •...
Page 112
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, Uconnect™ Phone can read or send new messages on • dry weather conditions, and your phone. • operation from the driver’s seat. Read Messages: • Performance, such as audio clarity, echo, and loudness If you receive a new text message while your phone is to a large degree rely on the phone and network, and connected to Uconnect™...
Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Send Messages: 3. Where are you? You can send messages using Uconnect™ Phone. To send 4. I need more direction. a new message: 5. L O L • Press the button. 6. Why •...
Page 114
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Can this wait? Bluetooth Communication Link Mobile phones have been found to lose connection to the 17. Bye for now Uconnect™ Phone. When this happens, the connection 18. When can we meet can generally be reestablished by switching the phone off/on.
Page 115
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113...
Page 116
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115...
Page 118
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is set to low.
Page 122
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Say a command (e.g., “Help”). Radio AM To switch to the AM band, say “AM” or “Radio AM”. In 3. Use the ON/OFF VOLUME rotary knob to adjust the this mode, you may say the following commands: volume to a comfortable level while the Voice Command •...
Page 123
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • “Menu Radio” (to switch to the radio menu) Disc To switch to the disc mode, say “Disc”. In this mode, you • “Main Menu” (to switch to the main menu) may say the following commands: Satellite Radio •...
Page 124
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Switch to system setup” − “Continue” (to continue recording) • “Change to setup” − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) • “Main menu setup” or —...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Driver Seat Adjusting The Seat Forward Or Rearward On some models the driver’s seat can be equipped with The seat can be adjusted both forward and rearward. six-way power. The power seat controls are located on Push the four-way switch seat switch forward or rear- the outboard side of the driver’s seat cushion.
Page 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the four-way seat switch, the seat will move in the direction of the switch. Release the switch when you have reached the desired position.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to control which could cause a collision and serious the seat controls.
Page 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat — Manual Recliner WARNING! To recline the seatback, lift the recline lever, located on the outboard side of the seat, lean back and release the Do not ride with the seatback reclined so that the lever when you reach the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 controls for each seat are located on a switch bank near the bottom center of the instrument panel. You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE two to one, indicating the change. The LOW-level setting WARNING! (Continued) will turn OFF automatically after approximately 30 min- • Do not place anything on the seat that insulates utes. against heat, such as a blanket or cushion. This NOTE: Once a heat setting is selected, heat will be felt may cause the seat heater to overheat.
Page 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Extended Cab/Crew Cab Rear Seat More cargo space is available by lifting up on the rear seat cushion. The Crew Cab Rear Seat is a 60/40 split cushion and full back. Either cushion can be raised, independently. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlights, Parking Lights And Panel Lights The headlight switch is located on the left side of the When the headlight switch is rotated to the first instrument panel next to the steering wheel. position, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Headlight Delay turned OFF. The lights illuminate at less than normal To aid in your exit, your vehicle is equipped with a intensity. If the parking brake is applied or the transmis- headlight delay that will leave the headlight on for sion is in the PARK position, the Daytime Running Lights 60 seconds.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out.
Page 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Turn Signals NOTE: • If either light remains on and does not flash, or there is Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show a very fast flash rate, check for a defective outside light proper operation of the front and rear turn signal lights.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High/Low Beam Switch Battery Saver Pull the multifunction lever fully toward the steering To protect the life of your vehicle’s battery, Load Shed- wheel to switch the headlights from high or low beam. ding is provided for both the interior and exterior lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Cargo Light — If Equipped WINDSHIELD WIPERS AND WASHERS The cargo lights are turned on by pressing on cargo The multifunction lever is located on the left side of the button. The cargo lights will also turn on for 30 seconds steering column.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers Intermittent Wiper System The wipers and washers are operated by a switch in the The intermittent feature of this system was designed for multifunction lever. Turn the end of the multifunction use when weather conditions make a single wiping cycle, lever to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Elec- To Deactivate tronic Speed Control System has been designed to shut A soft tap on the brake pedal, normal braking, or pressing down if multiple Speed Control functions are operated at the CANCEL button will deactivate the speed control the same time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 To Vary The Speed Setting To Accelerate For Passing When the Electronic Speed Control System is ON, the Press the accelerator as you would normally. When the speed can be increased by pressing and holding the pedal is released, the vehicle will return to the set speed.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE WARNING! The overhead console has the following features: Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • Compass/Temperature Mini-Trip Computer — If NOTE: The courtesy/reading lights will remain on until Equipped the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior Courtesy/Reading Lights lights are left on after the vehicle is turned OFF, they will Near the front of the console are two courtesy/reading...
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE US/M Button RESET Button Use the US/M button to change the display from U.S. to Use the RESET button to reset the following displays: metric measurement units. • Average Fuel Economy • Trip Odometer •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 STEP Button Average Fuel Economy (AVG ECO) Use the STEP button to choose, or cycle through, the four Displays the average fuel economy since the last reset. trip conditions. Average fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The DTE is not resettable. Resetting of this screen will cause the trip odometer to change to zero. Then the trip odometer must be reset in When Distance To Empty = LOW FUEL, the fuel gauge order to update the trip odometer miles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Global Reset If the RESET button is pressed twice within two seconds while in any of the three resettable displays (AVG ECO, ODO, ET), the GLOBAL RESET will reset all three displays. Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°...
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Compass Calibration If the compass appears erratic and the CAL symbol does This compass is self-calibrating which eliminates the not appear, you must manually put the compass into the need to manually set the compass. When the vehicle is “Calibration”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 button to select the new variance zone and press the RESET button to resume normal operation. Outside Temperature Because the ambient temperature sensor is located under the hood, engine temperature can influence the displayed temperature;...
Page 156
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons are located in the overhead WARNING! console designating the different HomeLink channels. • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Programming HomeLink Your vehicle should be parked outside of the garage while training. Before You Begin The Compass Mini-Trip Computer (CMTC) illuminates 1. Turn the ignition switch to the ON/RUN position. the HomeLink symbol (a house with an arrow inside it) 2.
Page 158
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the signal is too weak to train, replace the battery in the This can usually be found where the hanging antenna handheld transmitter. wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the NOTE: Some gate operators and garage door openers door).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 6. Firmly press and release the LEARN or TRAINING Gate Operator/Canadian Programming button. The name and color of the button may vary by Canadian radio-frequency laws require transmitter sig- manufacturer. nals to “time-out” (or quit) after several seconds of transmission –...
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you unplugged the device for training, plug it back in 2. Press and hold the desired HomeLink button for at this time. 20 seconds until the indicator(s) starts to flash. Do not release the button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Troubleshooting Tips 2. This device must accept any interference that may be If you are having trouble programming HomeLink , here received including interference that may cause undesired are some of the most common solutions: operation.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS When the optional Cigar Lighter heating element is used, This vehicle has two 12 Volt (13 Amp) auxiliary power it heats when pushed in and pops out automatically outlets that can provide power for accessories designed when ready for use.
Page 163
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. •...
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS CAUTION! If your vehicle has bucket seats with a center console, • Many accessories that can be plugged in, draw there are three cupholders located on the console. power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Open Crate Rear Cup Holders — Crew Cab REAR CRATE ’N GO STORAGE — IF EQUIPPED 1 — Crate Handles 2 — Crate End Flaps The rear Crate ’n Go storage, located under the rear seat 3 —...
Page 166
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To remove the crate, press on the release lever, located on To collapse the crate, push the crate end flaps inward to the ends of the base, and lift up on the crate. disengage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Plastic Grocery Bag Retainers CONSOLE FEATURES — IF EQUIPPED Retainer hooks, which will hold plastic grocery bag Floor Console Features handles, are built into the back panel of the cab. The Floor Console between the driver’s and front pas- senger’s seat has the following features: •...
Page 168
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Coin slots (located under the instrument panel center WARNING! stack). Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Power Outlet And Portable Phone Storage CARGO AREA FEATURES The console is equipped with a power outlet and an Rear Cargo Area Utility Rails — If Equipped iPod/phone storage bin. The phone storage bin can be used when easy access to the phone is needed.
Page 170
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To move the cleat to any position on the rail, turn the nut To remove the cleats from the utility rail, remove the end counterclockwise, approximately three turns. Then pull cap by pushing up on the locking tab, located on the out on the cleat and slide it to the detent nearest the bottom of the end cap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 REAR WINDOW FEATURES CAUTION! Rear Window Defroster — If Equipped Failure to follow these cautions can cause damage to The rear window defroster button is located on the the heating elements: right-side of the Air Conditioning and Heater •...
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Rear Window — If Equipped SLIDE-IN CAMPERS A locking device in the center of the window helps to Camper Applications prevent entry from the rear of the vehicle. Squeeze the Certain truck models are not recommended for slide-in lock to release the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To mount a camper unit with an overhang, the tailgate 2. Unclip and remove the cables from the box while can be removed. Unlatch the tailgate and remove the maintaining a 45 degree angle. support cables from the retainer pins.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Two-Position Tailgate/Upper Load Platform Your tailgate can be opened to the full-open or the partial-open position. The partial-open position is for loading objects longer than the length of the bed (sheets of plywood, etc.) by creating an upper load platform: Installing Lumber 1.
Page 175
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 4. Snap the tailgate support cable between the cable 2. Remove both cables from between the cable guides guide and the tailgate bumper. Do this on both sides of and the tailgate bumpers, and lower the tailgate. the tailgate.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 INSTRUMENT CLUSTER DESCRIPTIONS 3. Turn Signal Indicators When a turn signal is activated, a right-pointing or 1. Fuel Gauge left-pointing arrow lights up and flashes to indicate The fuel gauge shows the level of fuel in the fuel tank the direction of the turn.
Page 182
180 UNDERSTANDING YOUR INSTRUMENT PANEL 5. High Beam Indicator 7. Engine Temperature Warning Light The high beam indicator will illuminate if the This light warns of an overheated engine condi- headlights are on high beam. tion. As temperatures rise and the gauge ap- proaches H (Hot), this indicator will illuminate 6.
Page 183
UNDERSTANDING YOUR INSTRUMENT PANEL 181 the charging system light remains on, it means that the WARNING! vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- A hot engine cooling system is dangerous. You or rized dealer.
Page 184
182 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light remains on or turns on while driving, it 13. Tachometer indicates that the Anti-Lock portion of the brake system The tachometer gauge measures engine revolutions-per- is not functioning and that service is required. However, minute (RPM x 1000).
Page 185
UNDERSTANDING YOUR INSTRUMENT PANEL 183 16. Odometer Display Vehicle Odometer Messages The odometer display shows the total distance the ve- When the appropriate conditions exist, the following hicle has been driven. messages will display in the odometer: U.S. Federal regulations require that upon transfer of door .
Page 186
184 UNDERSTANDING YOUR INSTRUMENT PANEL gASCAP CHAngE OIL Message If the vehicle diagnostic system determines that the fuel Your vehicle is equipped with an engine oil change filler cap is loose, improperly installed, or damaged, a indicator system. The “CHAngE OIL” message will flash “gASCAP”...
Page 187
UNDERSTANDING YOUR INSTRUMENT PANEL 185 2. Fully depress the accelerator pedal slowly three CAUTION! times within 10 seconds. Continuous driving with the Transmission Tempera- 3. Turn the ignition switch to the OFF/LOCK position. ture Warning Light illuminated will eventually cause NOTE: If the indicator message illuminates when you severe transmission damage or transmission failure.
Page 188
186 UNDERSTANDING YOUR INSTRUMENT PANEL lit with the engine running, your vehicle will usually be If the light remains on when the parking brake has been drivable; however, see an authorized dealer for service as disengaged, and the fluid level is at the full mark on the soon as possible.
Page 189
UNDERSTANDING YOUR INSTRUMENT PANEL 187 NOTE: The light may flash momentarily during sharp Operation of the Brake Warning Light can be checked by cornering maneuvers which change fluid level condi- turning the ignition switch from the OFF position to the tions.
Page 190
188 UNDERSTANDING YOUR INSTRUMENT PANEL RUN and remain on, as a bulb check, until the engine is CAUTION! started. If the vehicle is not ready for emissions testing, the light will come on when the ignition is first turned to Prolonged driving with the MIL on could cause ON/RUN and remain on for 15 seconds, then blink for damage to the engine control system.
Page 191
UNDERSTANDING YOUR INSTRUMENT PANEL 189 22. Tire Pressure Monitoring Telltale Light reduces fuel efficiency and tire tread life, and may affect Each tire, including the spare (if provided), the vehicle’s handling and stopping ability. should be checked monthly when cold and Please note that the TPMS is not a substitute for proper inflated to the inflation pressure recommended tire maintenance, and it is the driver’s responsibility to...
Page 192
190 UNDERSTANDING YOUR INSTRUMENT PANEL alternate tires or wheels on the vehicle that prevent the 23. Airbag Warning Light TPMS from functioning properly. Always check the This light will turn on for four to eight seconds TPMS malfunction telltale after replacing one or more as a bulb check when the ignition switch is first tires or wheels on your vehicle, to ensure that the turned to ON/RUN.
Page 193
UNDERSTANDING YOUR INSTRUMENT PANEL 191 25. SVC (Service) 4WD Indicator 29. 4WD LOW Indicator The SVC 4WD illuminates when the ignition key is This light alerts the driver that the vehicle is in turned to the ON/RUN position and will stay on for two the four-wheel drive LOW mode.
192 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 230 (REQ) — AM/FM STEREO Operating Instructions - Radio Mode RADIO AND 6–DISC CD/DVD CHANGER NOTE: The ignition switch must be in the ON or ACC (MP3/WMA AUX JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 195
UNDERSTANDING YOUR INSTRUMENT PANEL 193 SEEK Buttons If your vehicle is not equipped with or this feature is not Press and release the SEEK buttons to search for the next available on your vehicle, a “Not Equipped With listenable station in AM/FM mode. Press the right switch Uconnect Phone”...
Page 196
194 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure INFO Button Press the INFO button for an RDS station (one with call 1. Press and hold the TIME button until the hours blink. letters displayed). The radio will return a Radio Text 2.
Page 197
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Push the rotary TUNE/SCROLL control knob a second MUSIC TYPE Button time and MID will display. Turn the TUNE/SCROLL Pressing this button once will turn on the Music Type control knob to the right or left to increase or decrease the mode for five seconds.
Page 198
196 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type 16-Digit Character Display Program Type 16-Digit Character Display Information Inform Top 40 Top 40 Jazz Jazz Weather Weather News News By pressing the SEEK button when the Music Type icon Nostalgia Nostalga is displayed, the radio will be tuned to the next frequency Oldies Oldies station with the same selected Music Type name.
Page 199
UNDERSTANDING YOUR INSTRUMENT PANEL 197 • DVD Enter - When the disc is in DVD Menu mode, • Angle – Repeatedly pressing SELECT will change selecting DVD Enter will allow you to play the current the viewing angle if supported by the DVD disc (if highlighted selection.
Page 200
198 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Home Clock - Pressing the SELECT button allows Audio Language — If Equipped you to set the clock. Turn the TUNE/SCROLL control Selecting this item allows you to choose a default audio knob to adjust the hours and then press and turn the language (effective only if the language is supported by TUNE/SCROLL control knob to adjust the minutes.
Page 201
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Audio DRC — If Equipped NOTE: The user will have to set these defaults before Selecting this item allows you to limit maximum audio loading a disc. If changes are made to these settings after dynamic range.
200 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions - (DISC MODE for CD and repeating the above procedure with this exception: Press MP3/WMA Audio Play, DVD-VIDEO) the SET button twice and SET 2 will show in the display The radio DVD player and many DVD discs are coded by window.
Page 203
UNDERSTANDING YOUR INSTRUMENT PANEL 201 NOTE: The ignition switch must be in the ON or ACC Eject Button — Ejecting Compact Disc(s) position to operate the radio. Press the EJECT button and the pushbutton with the corresponding number (1-6) where the LOAD Button —...
202 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE) Notes On Playing MP3/WMA Files Press the SCAN button to scan through each track on the The radio can play MP3/WMA files; however, acceptable CD currently playing. MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the TIME Button (CD MODE) following restrictions.
Page 205
UNDERSTANDING YOUR INSTRUMENT PANEL 203 The radio uses the following limits for file systems: If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ • Maximum number of directory levels: 8 WMA tracks on that disc.
Page 206
204 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3/WMA Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3/WMA data is loaded, Specification quency (kHz) the radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
UNDERSTANDING YOUR INSTRUMENT PANEL 205 LIST Button (DISC Mode for MP3/WMA Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 208
206 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Auxiliary Mode) Operating Instructions — Voice Command System No function. (If Equipped) For the radio, Refer to “Voice Command” in the EJECT Button (Auxiliary Mode) Uconnect™ User Manual located on the DVD for further No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Macrovision NOTE: Sirius service is not available in Hawaii and has This product incorporates copyright protection technol- limited coverage in Alaska. ogy that is protected by U.S. patents and other intellec- System Activation tual property rights. Use of this copyright protection Sirius Satellite Radio service is pre-activated, and you technology must be authorized by Macrovision, and is may begin listening immediately to the one year of audio...
Page 210
208 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Your Vehicle Identification Number. placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as To access the ESN/SID, refer to the following steps: bikes should be placed as far rearward as possible, within ESN/SID Access the loading design of the rack.
Page 211
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Operating Instructions - Uconnect™ Multimedia INFO Button (Satellite) Mode Pressing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- NOTE: The ignition switch must be in the ON/RUN or able).
Page 212
210 UNDERSTANDING YOUR INSTRUMENT PANEL or turning the TUNE/SCROLL control knob within five SET Button – To Set the Pushbutton Memory seconds will allow the program format type to be selected. When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Buttons 1 - 6 Operating Instructions — Radio Mode These buttons tune the radio to the channels that you NOTE: The ignition switch must be in the ON or ACC commit to pushbutton memory (12 Satellite stations). position to operate the radio.
Page 214
212 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
Page 215
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
214 UNDERSTANDING YOUR INSTRUMENT PANEL SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE For CD And and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice.
Page 217
UNDERSTANDING YOUR INSTRUMENT PANEL 215 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
216 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD and MP3 modes. Random Play.
Page 219
UNDERSTANDING YOUR INSTRUMENT PANEL 217 • Maximum number of characters in file/folder names: Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 • Level 1: 12 (including a separator . and a three- Level 1 and Level 2 and includes the Joliet extension. character extension) When reading discs recorded using formats other than •...
Page 220
218 UNDERSTANDING YOUR INSTRUMENT PANEL When using the MP3 encoder to compress audio data to Playlist files are not supported. MP3 Pro files are not an MP3 file, the bit rate and sampling frequencies in the supported. following table are supported. In addition, variable bit Playback of MP3 Files rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 To increase the speed of disc loading, it is recommended NOTE: The AUX device must be turned on and the to use CD-R media and single-session discs. To create a device’s volume set to proper level. If the AUX audio is single-session disc, enable the “Disc at Once”...
220 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 WITH SATELLITE RADIO Operating Instructions — Radio Mode (SALES CODE RES+RSC) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 223
UNDERSTANDING YOUR INSTRUMENT PANEL 221 SEEK Buttons Phone Button Uconnect™ Phone — If Equipped Press and release the SEEK buttons to search for the next Press this button to operate the Uconnect™ Phone feature listenable station in AM/FM mode. Press the right switch (if equipped).
Page 224
222 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call will begin to blink. letters displayed).
Page 225
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Push the rotary TUNE/SCROLL control knob a second MUSIC TYPE Button time and MID will display. Turn the TUNE/SCROLL Pressing this button once will turn on the Music Type control knob to the right or left to increase or decrease the mode for five seconds.
Page 226
224 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type 16-Digit Character Display Program Type 16-Digit Character Display Information Inform Top 40 Top 40 Jazz Jazz Weather Weather News News By pressing the SEEK button when the Music Type icon Nostalgia Nostalga is displayed, the radio will be tuned to the next frequency Oldies Oldies station with the same selected Music Type name.
Page 227
UNDERSTANDING YOUR INSTRUMENT PANEL 225 hours, press the TUNE/SCROLL control knob to set You may add a second station to each pushbutton by the minutes. The minutes will begin to blink. Adjust repeating the above procedure with this exception: Press the minutes using the right side TUNE/SCROLL the SET/RND button twice and SET 2 will show in the control knob.
226 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions — CD MODE for CD and If you insert a disc with the ignition ON and the radio MP3 Audio Play ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and •...
Page 229
UNDERSTANDING YOUR INSTRUMENT PANEL 227 EJECT Button - Ejecting a CD the current selection. Pressing and holding the SEEK Press the EJECT button to eject the CD. button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within...
228 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button (Random Play Button) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate The medium formats supported by the radio are ISO 9660 Random Play. This feature plays the selections on the Level 1 and Level 2 and includes the Joliet extension.
Page 231
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • Maximum number of characters in file/folder names: When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the • Level 1: 12 (including a separator . and a three- following table are supported.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Playlist files are not supported. MP3 Pro files are not To increase the speed of disc loading, it is recommended supported. to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option Playback of MP3 Files before writing to the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Press the INFO button once more to return to elapsed is not loud enough, turn the device’s volume up. If the time priority mode. AUX audio sounds distorted, turn the device’s volume down. Press and hold the INFO button for three seconds or more and the radio will display song titles for each file.
Page 234
232 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To access the ESN/SID, refer to the following steps: Sirius Satellite Radio service is pre-activated, and you ESN/SID Access may begin listening immediately to the one year of audio With the ignition switch in the ON/RUN or ACC posi- service that is included with the factory-installed satellite tion and the radio on, press the SETUP button and scroll radio system in your vehicle.
Page 235
UNDERSTANDING YOUR INSTRUMENT PANEL 233 bikes should be placed as far rearward as possible, within Operating Instructions - Uconnect™ Multimedia the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON/RUN or Reception Quality ACC position to operate the radio.
Page 236
234 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display informa- Pressing this button once will turn on the Music Type tion between Artist, Song Title, and Composer (if avail- mode for five seconds. Pressing the MUSIC TYPE button able).
Page 237
UNDERSTANDING YOUR INSTRUMENT PANEL 235 SETUP Button You may add a second channel to each pushbutton by Pressing the SETUP button allows you to select the repeating the above procedure with this exception: Press following items: the SET button twice and SET 2 will show in the display window.
236 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS — The right hand control is a rocker type switch with a push IF EQUIPPED button in the center. Pressing the top of the switch will The remote sound system controls are located on the rear increase the volume, and pressing the bottom of the surface of the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 The button located in the center of the left hand control CD/DVD DISC MAINTENANCE will tune to the next pre-set station that you have To keep a CD/DVD in good condition, take the following programmed in the radio pre-set push-buttons. precautions: CD Player 1.
238 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- knobs. These comfort controls can be set to obtain desired lar disc, it may be damaged (i.e., scratched, reflective interior conditions. coating removed, a hair, moisture or dew on the disc) Air Conditioning and Heater oversized, or have protection encoding.
Page 241
UNDERSTANDING YOUR INSTRUMENT PANEL 239 right of the control panel. Conditioned air will be di- NOTE: To improve your selection choices, the system rected through the outlets selected by the mode control. allows you to operate at intermediate positions between A light at the top of the SNOWFLAKE button shows that the major modes.
Page 242
240 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level NOTE: • The air conditioner compressor operates in both Mix Outside air flows through the outlets located in the instrument panel and at the floor. and Defrost or a blend of these modes, even if the A/C button has not been pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 NOTE: For vehicles equipped with Remote Start, the Side window demisters direct airflow specifically to the climate controls will not function during Remote Start window glass to help prevent interior fogging of the operation if the blower control is left in the “O” (Off) glass.
Page 244
242 UNDERSTANDING YOUR INSTRUMENT PANEL drive with the windows open for the first few minutes. As the temperature gets colder it may be necessary to Once the hot air has been expelled, close the windows direct air onto the windshield by using MIX Mode and turn the mode selector to the Recirculation Panel position on the control.
Page 245
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Summer Operation gear and set the air conditioner to recirculation mode. Air conditioned vehicles must be protected with a high Operating the air conditioner in recirculation mode pro- quality antifreeze coolant during summer, to provide vides the maximum performance from your air condi- proper corrosion protection and to raise the boiling point tioning.
Page 248
246 STARTING AND OPERATING Limited-Slip Rear Axle Differential — If Brake System ......273 Equipped ......264 ▫...
Page 249
STARTING AND OPERATING 247 ▫ Spare Tire Matching Original Equipped Tire ▫ General Information ....301 And Wheel – If Equipped ....287 Fuel Requirements .
STARTING AND OPERATING 249 STARTING PROCEDURES NOTE: This vehicle is equipped with a transmission Before starting your vehicle, adjust your seat, adjust both shift interlocking system. The brake pedal must be inside and outside mirrors, and fasten your seat belts. pressed to shift out of PARK.
250 STARTING AND OPERATING Turn the ignition switch to the START position and WARNING! (Continued) release when the engine starts. If the engine fails to start • Do not attempt to push or tow your vehicle to get within 10 seconds, turn the key to the OFF position, wait it started.
STARTING AND OPERATING 251 After Starting CAUTION! The idle speed is automatically controlled and will de- crease as the engine warms up. To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to ENGINE BLOCK HEATER —...
252 STARTING AND OPERATING WARNING! CAUTION! (Continued) • Do not shift from REVERSE, PARK, or NEUTRAL Remember to disconnect the engine block heater into any forward gear when the engine is above cord before driving. Damage to the 110-115 Volt idle speed.
STARTING AND OPERATING 253 Key Ignition Park Interlock Automatic Transmission This vehicle is equipped with a Key Ignition Park Inter- The electronic PRNDL on the instrument cluster indicates lock which requires the shift lever to be placed in PARK the transmission gear selected. The shift lever is mounted prior to rotating the key to the LOCK position.
Page 256
254 STARTING AND OPERATING WARNING! WARNING! (Continued) • Unintended movement of a vehicle could injure • Never use the PARK position as a substitute for those in and near the vehicle. As with all vehicles, the parking brake. Always apply the parking you should never exit a vehicle while the engine is brake fully when parked to guard against vehicle running.
Page 257
STARTING AND OPERATING 255 NEUTRAL when going down hill, use first gear. To prevent excessive This range is used when vehicle is standing for pro- engine speed do not exceed 25 mph (40 km/h) in this longed periods with engine running. Engine may be range.
Page 258
256 STARTING AND OPERATING NOTE: The transmission will downshift from Overdrive to • If the vehicle is started in extremely cold temperatures, DRIVE if the accelerator pedal is fully pressed at vehicle the transmission may not shift into Overdrive and will speeds above approximately 35 mph (56 km/h).
Page 259
STARTING AND OPERATING 257 Torque Converter Clutch A feature designed to improve fuel economy is included in all automatic transmissions. A clutch, within the torque converter, engages automatically at a calibrated speed at light throttle. It engages at higher speeds under heavier acceleration.
258 STARTING AND OPERATING transmission is sufficiently warm, will demonstrate that the transmission is able to shift into, and out of Overdrive. • If the vehicle has not been driven in several days, the first few seconds of operation after shifting the trans- mission into gear may seem sluggish.
Page 261
STARTING AND OPERATING 259 The transfer case is designed to be driven in the two- case NEUTRAL position is to be used for recreational wheel drive position (2WD) for normal street and high- towing only. Refer to “Recreational Towing” in “Starting way conditions on dry hard-surfaced roads.
Page 262
260 STARTING AND OPERATING five seconds, and retry selection. To find the shift require- NOTE: Do not attempt to make a shift while only the ments, refer to the Shifting Procedure for further front or rear wheels are spinning. The transfer case is not information.
Page 263
STARTING AND OPERATING 261 4WD LOCK WARNING! Four-Wheel Drive Lock — This range locks the front and rear driveshafts together forcing the front and rear You or others could be injured if you leave the wheels to rotate at the same speed. This range provides vehicle unattended with the transfer case in the additional traction for loose or slippery road surfaces NEUTRAL position without first fully engaging the...
262 STARTING AND OPERATING Shifting Procedure ignition key must be in the ON position with the engine either running or OFF. This shift cannot be completed if NOTE: If any of the requirements to select a new the key is in the ACC position. transfer case position have not been met, the transfer case will not shift, the indicator light for the previous position NOTE: On vehicles equipped with Anti-Lock Brake...
Page 265
STARTING AND OPERATING 263 Shifting can be performed with the vehicle rolling 2 to 3. Turn the transfer case switch to the desired position. 3 mph (3 to 5 km/h), or completely stopped. USE 4. After the desired position indicator light is ON (not EITHER OF THE FOLLOWING PROCEDURES: flashing), shift the transmission back into gear.
264 STARTING AND OPERATING LIMITED-SLIP REAR AXLE DIFFERENTIAL — IF Care should be taken to avoid sudden accelerations when EQUIPPED both rear wheels are on a slippery surface. This could The limited-slip differential provides additional traction cause both rear wheels to spin, and allow the vehicle to on snow, ice, mud, sand and gravel.
STARTING AND OPERATING 265 2. Slow down if the road has standing water or puddles. WARNING! 3. Replace tires when tread wear indicators first become Rapid acceleration on slippery surfaces is dangerous. visible. Unequal traction can cause sudden pulling of the rear 4.
266 STARTING AND OPERATING Flowing/Rising Water CAUTION! • Always check the depth of the standing water WARNING! before driving through it. Never drive through Do not drive on or across a road or path where water standing water that is deeper than the bottom of is flowing and/or rising (as in storm run-off).
Page 269
STARTING AND OPERATING 267 CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
268 STARTING AND OPERATING OFF-ROAD DRIVING TIPS always a good idea to check for damage. That way you Care should be taken when attempting to climb steep can get any problems taken care of right away and have hills or driving diagonally across a hill or slope. If natural your vehicle ready when you need it.
STARTING AND OPERATING 269 • After extended operation in mud, sand, water, or POWER STEERING similar dirty conditions, have the radiator, fan, brake The standard power steering system will give you good rotors, wheels, brake linings, and axle yokes inspected vehicle response and increased ease of maneuverability and cleaned as soon as possible.
270 STARTING AND OPERATING system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are does not in any way damage the steering system. apparent, and/or the system is not functioning as antici- pated.
STARTING AND OPERATING 271 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the...
Page 274
272 STARTING AND OPERATING When parking on a hill, it is important to turn the front WARNING! (Continued) wheels toward the curb on a downhill grade and away • Never leave children alone in a vehicle. Leaving from the curb on an uphill grade. Apply the parking unattended children in a vehicle is dangerous for a brake before placing the shift lever in PARK, otherwise number of reasons.
STARTING AND OPERATING 273 force required to slow or stop, and activation of the CAUTION! “Brake Warning Light” and the “ABS Warning Light” during brake use. If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction Four-Wheel Anti-Lock Brake System (ABS) is indicated.
Page 276
274 STARTING AND OPERATING WARNING! WARNING! (Continued) • The ABS cannot prevent collisions, including Pumping of the Anti-Lock Brakes will diminish their those resulting from excessive speed in turns, effectiveness and may lead to a collision. Pumping following another vehicle too closely, or hydro- makes the stopping distance longer.
STARTING AND OPERATING 275 TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 278
276 STARTING AND OPERATING • High flotation tire sizing is based on U.S. design Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- standards and it begins with the tire diameter molded tion.
Page 279
STARTING AND OPERATING 277 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
278 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
STARTING AND OPERATING 279 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
280 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire Placard Location...
Page 283
STARTING AND OPERATING 281 axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 284
282 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- 6. If your vehicle will be towing a trailer, load from your sengers from XXX lbs or XXX kg. trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available 4.
284 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
STARTING AND OPERATING 285 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to The pressure should be checked and adjusted as well as the right or left.
286 STARTING AND OPERATING Inflation pressures specified on the placard are always Example: If garage temperature = 68°F (20°C) and the “cold tire inflation pressure.” Cold tire inflation pressure outside temperature = 32°F (0°C) then the cold tire is defined as the tire pressure after the vehicle has not inflation pressure should be increased by 3 psi (21 kPa), been driven for at least three hours or driven less than which equals 1 psi (7 kPa) for every 12°F (7°C) for this...
STARTING AND OPERATING 287 Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your Spare Tire Matching Original Equipped Tire and tires could cause them to fail.
288 STARTING AND OPERATING If your vehicle is not equipped with an original equip- Compact Spare Tire – If Equipped ment tire and wheel as a spare, a non-matching tempo- The compact spare is for temporary emergency use only. rary emergency use spare may be equipped with your You can identify if your vehicle is equipped with a vehicle.
STARTING AND OPERATING 289 your original equipment tire, replace (or repair) the WARNING! original equipment tire and reinstall on the vehicle at the first opportunity. Compact spares are for temporary emergency use only. With these spares, do not drive more than Limited-Use Spare –...
290 STARTING AND OPERATING Refer to “Freeing A Stuck Vehicle” in “What To Do In WARNING! Emergencies” for further information. Limited-use spares are for emergency use only. In- WARNING! stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the Fast spinning tires can be dangerous.
STARTING AND OPERATING 291 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread.
292 STARTING AND OPERATING Replacement Tires WARNING! The tires on your new vehicle provide a balance of many • Do not use a tire, wheel size or rating other than characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- that specified for your vehicle.
STARTING AND OPERATING 293 TIRE CHAINS WARNING! (Continued) • Failure to equip your vehicle with tires having CAUTION! adequate speed capability can result in sudden tire • The use of chains is permitted only on vehicles failure and loss of vehicle control. equipped with P245/70R16 tires.
Page 296
294 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Do not install tire chains on front wheels of To avoid damage to your vehicle, tires or chains, vehicles. observe the following precautions: • Do not drive for a prolonged period on dry pave- •...
STARTING AND OPERATING 295 Snow tires generally have lower speed ratings than what CAUTION! was originally equipped with your vehicle and should • Do not use tire chains on vehicles equipped with not be operated at sustained speeds over 75 mph (120 km/h).
296 STARTING AND OPERATING These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels, and contribute to a smooth, quiet ride.
Page 299
STARTING AND OPERATING 297 The tire pressure will vary with temperature by about turn off until the tire pressure is at or above recom- 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that mended cold placard pressure. Once the low tire pressure when the outside temperature decreases, the tire pressure warning has been illuminated, the tire pressure must be will decrease.
Page 300
298 STARTING AND OPERATING Lamp” will still be ON. In this situation, the “TPMS CAUTION! (Continued) Lamp” will turn off only after the tires have been inflated • After inspecting or adjusting the tire pressure to the vehicle’s recommended cold placard pressure always reinstall the valve stem cap.
STARTING AND OPERATING 299 • The TPMS is not a substitute for proper tire mainte- The TPMS consists of the following components: nance, and it is the driver’s responsibility to maintain • Receiver module correct tire pressure using an accurate tire gauge, even •...
Page 302
300 STARTING AND OPERATING The “Tire Pressure Monitoring Telltale Light” will flash on 2. If you install the full size spare tire in place of a road and off for 75 seconds, and remain on solid when a system tire that has a pressure below the low-pressure warning fault is detected.
STARTING AND OPERATING 301 active road tires. The vehicle may need to be driven for FUEL REQUIREMENTS up to 20 minutes above 15 mph (24 km/h) in order for the These engines are designed to meet all TPMS to receive this information. emissions regulations, and provide excel- lent fuel economy and performance when General Information...
302 STARTING AND OPERATING Over 40 auto manufacturers worldwide, have issued and Gasoline/Oxygenate Blends endorsed consistent gasoline specifications (the World- Some fuel suppliers blend unleaded gasoline with oxy- wide Fuel Charter, WWFC), which define fuel properties genates such as Ethanol. Fuels blended with oxygenates necessary to deliver enhanced emissions, performance, may be used in your vehicle.
STARTING AND OPERATING 303 • disconnect and reconnect the battery to reset the E-85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline contain- engine controller memory ing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged content may void the vehicle’s warranty.
304 STARTING AND OPERATING be used at levels higher than those allowed in the United CAUTION! (Continued) States. MMT is prohibited in Federal and California • The use of leaded gas is prohibited by Federal law. reformulated gasoline. Using leaded gasoline can impair engine perfor- Materials Added To Fuel mance, damage the emission control system.
STARTING AND OPERATING 305 Carbon Monoxide Warnings CAUTION! (Continued) • The use of fuel additives which are now being WARNING! sold as octane enhancers is not recommended. Carbon monoxide (CO) in exhaust gases is deadly. Many of these products contain high concentra- Follow the precautions below to prevent carbon tions of methanol.
306 STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. FLEXIBLE FUEL (4.7L ENGINE ONLY) —...
STARTING AND OPERATING 307 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
308 STARTING AND OPERATING • you do not add less than 5 gallons (19 Liters) when Selection Of Engine Oil For Flexible Fuel Vehicles refueling (E-85) and Gasoline Vehicles FFV vehicles operated on E-85 require specially formu- • you operate the vehicle immediately after refueling for lated engine oils.
STARTING AND OPERATING 309 NOTE: Use of the engine block heater (if equipped) is CAUTION! beneficial for E-85 startability when the ambient tempera- ture is less than 32°F (0°C). Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Cruising Range Because E-85 fuel contains less energy per gallon/liter Maintenance...
310 STARTING AND OPERATING ADDING FUEL If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. Fuel Filler Cap (Gas Cap) CAUTION! The gas cap is located behind the fuel filler door. When fueling, the cap may be placed on the inside of the filler •...
STARTING AND OPERATING 311 • Tighten the gas cap until you hear a “clicking” sound. WARNING! (Continued) This is an indication that the gas cap is properly • Never add fuel to the vehicle when the engine is tightened. Make sure that the gas cap is tightened each running.
312 STARTING AND OPERATING VEHICLE LOADING This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Certification Label Rating (GAWR) front and rear, and Vehicle Identification As required by National Highway Traffic Safety Admin- Number (VIN).
STARTING AND OPERATING 313 Gross Axle Weight Rating (GAWR) Inflation Pressure (Cold) The GAWR is the maximum permissible load on the front This is the cold tire inflation pressure for your vehicle for and rear axles. The load must be distributed in the cargo all loading conditions up to full GAWR.
314 STARTING AND OPERATING The entire vehicle should first be weighed on a commer- WARNING! cial scale to ensure that the GVWR has not been ex- ceeded. The weight on the front and rear of the vehicle Do not load your vehicle any heavier than the GVWR should then be determined separately to be sure that the or the maximum front and rear GAWR.
STARTING AND OPERATING 315 Common Towing Definitions Gross Combination Weight Rating (GCWR) The following trailer towing related definitions will assist The GCWR is the total permissible weight of your vehicle you in understanding the following information: and trailer when weighed in combination. Gross Vehicle Weight Rating (GVWR) NOTE: The GCWR rating includes a 150 lbs (68 kg) The GVWR is the total allowable weight of your vehicle.
Page 318
316 STARTING AND OPERATING Trailer Tongue Weight (TW) Weight-Distributing Hitch The tongue weight is the downward force exerted on the A weight-distributing hitch works by applying leverage hitch ball by the trailer is the tongue weight. In most through spring (load) bars. They are typically used for cases it should not be less than 10% or more than 15% of heavier loads, to distribute trailer tongue weight to the the trailer load.
Page 319
STARTING AND OPERATING 317 WARNING! • An improperly adjusted weight-distributing hitch may reduce handling, stability, and braking per- formance, and could result in a collision. • Weight-Distributing Systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable rec- reational vehicle...
Page 320
318 STARTING AND OPERATING EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of Weight-Distributing Hitch (Incorrect)
STARTING AND OPERATING 319 Trailer Hitch Classification Trailer Hitch Classification Definitions The rear bumper is intended to tow trailers up to Class Max. Trailer Hitch Industry 2,000 lbs (907 kg) without added equipment or altera- Standards tions to the standard equipment. Your vehicle may be Class I - Light Duty 2,000 lbs (907 kg) factory equipped for safe towing of trailers weighing...
• http:// www.ramtrucks.com • http:// www.dodge.ca (Canada) Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the...
STARTING AND OPERATING 321 NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • Then, during the first 500 miles (805 km) that a factory-installed options, or dealer-installed options, trailer is towed, do not drive over 50 mph must be considered as part of the total load on your (80 km/h) and do not make starts at full throttle.
Page 324
322 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a and will not shift during travel. When trailering grade. When parking, apply the parking brake on cargo that is not fully secured, dynamic load shifts the tow vehicle.
Page 325
STARTING AND OPERATING 323 Towing Requirements – Tires − When replacing tires, refer to “Tires – General Infor- mation” in “Starting and Operating” for further infor- − Do not attempt to tow a trailer while using a compact mation. Replacing tires with a higher load carrying spare tire.
Page 326
324 STARTING AND OPERATING − Trailer brakes are recommended for trailers over WARNING! 1,000 lbs (454 kg) and required for trailers in excess of • Do not connect trailer brakes to your vehicle’s 2,000 lbs (907 kg). hydraulic brake lines. It can overload your brake CAUTION! system and cause it to fail.
Page 327
STARTING AND OPERATING 325 The Trailer Tow Package may include a four and seven- pin wiring harness. Use a factory approved trailer har- ness and connector. NOTE: Do not cut or splice wiring into the vehicle’s wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector.
326 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic Transmission The “DRIVE” range can be selected when towing. How- ever, if frequent shifting occurs while in this range, the TOW/HAUL feature should be selected.
STARTING AND OPERATING 327 NOTE: Check the automatic transmission fluid level Cooling System before towing. To reduce potential for engine and transmission over- heating, take the following actions: Tow/Haul – If Equipped To reduce potential for automatic transmission overheat- − City Driving ing, turn the TOW/HAUL feature ON when driving in When stopped for short periods of time, shift the trans- hilly areas or shift the transmission to Drive position 2 on...
328 STARTING AND OPERATING Four-Wheel Drive Models WARNING! CAUTION! Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. • Internal damage to the transfer case will occur if a This could adversely affect the functioning of the front or rear wheel lift is used when recreational airbag system in a collision and you could be injured.
Page 331
STARTING AND OPERATING 329 Recreational Towing Procedure CAUTION! WARNING! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- You or others could be injured if you leave the ational towing to prevent damage to internal parts. vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the 1.
Page 332
330 STARTING AND OPERATING 6. Using the point of a ballpoint pen or similar object, 9. Shift the transmission into REVERSE. press the transfer case NEUTRAL button for four sec- 10. Release the brake pedal for five seconds and ensure onds.
Page 333
STARTING AND OPERATING 331 prior to pressing the NEUTRAL button or are no Returning to Normal Operation longer met during the four second timer, then the Use the following procedure to prepare your vehicle for NEUTRAL indicator light will flash continuously until normal usage.
Page 334
332 STARTING AND OPERATING 8. After the NEUTRAL indicator light turns off, release position indicator lights will flash continuously until the NEUTRAL button. all requirements are met or until the NEUTRAL button is released. 9. After the NEUTRAL button has been released, the •...
Page 335
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....334 Jump-Starting Procedures ....345 ▫...
334 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Press the switch to turn on the Hazard Warning The Hazard Warning flasher switch is located on the top flasher. When the switch is activated, all directional of the steering column, just behind the steering wheel. turn signals will flash on and off to warn oncoming traffic of an emergency.
WHAT TO DO IN EMERGENCIES 335 JACKING AND TIRE CHANGING WARNING! (Continued) • The jack is designed to be used as a tool for WARNING! changing tires only. The jack should not be used to • Do not attempt to change a tire on the side of the lift the vehicle for service purposes.
Page 338
336 WHAT TO DO IN EMERGENCIES A finger-operated helper tool is provided to assist re- moval and stowage of the jack. This tool must be removed to operate the jack for changing the spare tire. Jack Screw Jack Stowage Location (Extended Cab)
WHAT TO DO IN EMERGENCIES 337 WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only.
Page 340
338 WHAT TO DO IN EMERGENCIES Steps for Removing the Spare Tire • Remove the jack from the stowage compartment using the supplied finger-assist tool. • Remove the finger-assist tool from jack and set aside until jack is stowed. • Assemble the jack tools. •...
Page 341
WHAT TO DO IN EMERGENCIES 339 Turning Lug Wrench and Extension Spare Tire Stowage Location It is recommended that you stow the flat or spare to NOTE: The winch mechanism is designed for use with avoid tangling the loose cable. the jack extension tube only.
340 WHAT TO DO IN EMERGENCIES Preparations 4. Place the shift lever in PARK (automatic transmission). On 4-Wheel Drive vehicles, shift the transfer case to the 1. Park the vehicle on a firm, level surface. Avoid icy or 4L position. slippery areas.
WHAT TO DO IN EMERGENCIES 341 Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. Carefully follow these tire changing warnings to • Do not get under the vehicle when it is on a jack. help prevent personal injury or damage to your •...
Page 344
342 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Lower and remove the spare wheel, jack, and tools from stowage. 2.
Page 345
WHAT TO DO IN EMERGENCIES 343 Left Rear Jacking Location Right Rear Jacking Location NOTE: Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 5.
Page 346
344 WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make A loose tire or jack thrown forward in a collision or the vehicle unstable and cause a collision. It could hard stop could injure someone in the vehicle. Al- slip off the jack and hurt someone near it.
WHAT TO DO IN EMERGENCIES 345 To Stow The Flat Or Spare WARNING! (Continued) Turn the wheel so that the valve stem is down. Slide the • Always park on a firm, level surface as far from wheel retainer through the center of the wheel and the edge of the roadway as possible before raising position it properly across the wheel opening.
346 WHAT TO DO IN EMERGENCIES another vehicle or by using a portable battery booster Preparations For Jump-Start pack. Jump-starting can be dangerous if done improperly The battery in your vehicle is located in the front of the so please follow the procedures in this section carefully. engine compartment, behind the left headlight assembly.
WHAT TO DO IN EMERGENCIES 347 3. If using another vehicle to jump-start the battery, park WARNING! the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 350
348 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in Do not connect the cable to the negative post (-) of the damage to the charging system of the booster vehicle discharged battery. The resulting electrical spark or the discharged vehicle.
WHAT TO DO IN EMERGENCIES 349 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion.
Page 352
350 WHAT TO DO IN EMERGENCIES idle with the shift lever in NEUTRAL for at least one WARNING! minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmis- Fast spinning tires can be dangerous. Forces gener- sion failure during prolonged efforts to free a stuck ated by excessive wheel speeds may cause damage, or vehicle.
WHAT TO DO IN EMERGENCIES 351 EMERGENCY TOW HOOKS — IF EQUIPPED WARNING! Your vehicle may be equipped with emergency tow • Chains are not recommended for freeing a stuck hooks. vehicle. Chains may break, causing serious injury or death. •...
352 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE rear wheels on the ground. The speed must not exceed Proper towing or lifting equipment is required to prevent 30 mph (50 km/h), and the distance must not exceed damage to your vehicle. Use of safety chains is recom- 15 miles (25 km).
MAINTAINING YOUR VEHICLE 357 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
358 MAINTAINING YOUR VEHICLE the message will appear the next time the vehicle is Normally, the OBD II system will be ready. The OBD II started. This might indicate a damaged cap. If the prob- system may not be ready if your vehicle was recently lem is detected twice in a row, the system will turn on the serviced, recently had a dead battery or a battery replace- MIL.
MAINTAINING YOUR VEHICLE 359 4. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. a. The MIL will flash for about 10 seconds and then Regardless of whether your vehicle’s OBD II system is return to being fully illuminated until you turn OFF ready or not, if the MIL is illuminated during normal...
360 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
MAINTAINING YOUR VEHICLE 361 Checking the oil while the vehicle is on level ground will CAUTION! (Continued) improve the accuracy of the oil level readings. Always • Your vehicle has been built with improved fluids maintain the oil level within the SAFE zone on the that protect the performance and durability of dipstick.
Page 364
362 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change CAUTION! intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is Engine Oil Selection not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 363 Synthetic Engine Oils Engine Oil Filter You may use synthetic engine oils, provided the recom- The engine oil filter should be replaced with a new filter mended oil quality requirements are met, and the recom- at every engine oil change. mended maintenance intervals for oil and filter changes Engine Oil Filter Selection are followed.
364 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Selection WARNING! The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be The air induction system (air cleaner, hoses, etc) can used to assure most efficient service. MOPAR engine air provide a measure of protection in the case of engine cleaner filters are a high quality filter and are backfire.
Page 367
MAINTAINING YOUR VEHICLE 365 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
366 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
MAINTAINING YOUR VEHICLE 367 Refrigerant Recovery And Recycling hood latching components to ensure proper function. R-134a air conditioning refrigerant is a hydrofluoro- When performing other underhood services, the hood carbon (HFC) that is endorsed by the Environmental latch, release mechanism and safety catch should be Protection Agency (EPA), and is an ozone-saving prod- cleaned and lubricated.
368 MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from exceeds the temperature range of your climate. This the windshield. Keep the blade rubber out of contact with rating information can be found on most washer fluid petroleum products such as engine oil, gasoline, etc.
Page 371
MAINTAINING YOUR VEHICLE 369 have an authorized technician inspect the complete ex- WARNING! (Continued) haust system and adjacent body areas for broken, dam- • A hot exhaust system can start a fire if you park aged, deteriorated, or mispositioned parts. Open seams over materials that can burn.
Page 372
370 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control CAUTION! (Continued) systems can result in civil penalties being assessed • Damage to the catalytic converter can result if your against you. vehicle is not kept in proper operating condition. In unusual situations involving grossly malfunctioning In the event of engine malfunction, particularly engine operation, a scorching odor may suggest severe...
MAINTAINING YOUR VEHICLE 371 • Do not idle the engine with any spark plug wires rusty in appearance, the system should be drained, disconnected or removed, such as when diagnostic flushed and refilled with fresh engine coolant (anti- testing, or for prolonged periods during very rough freeze).
Page 374
372 MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush, And Refill CAUTION! If the engine coolant (antifreeze) is dirty or contains a • Mixing of engine coolant (antifreeze) other than considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough specified HOAT engine coolant (antifreeze) may rinsing to remove all deposits and chemicals.
Page 375
MAINTAINING YOUR VEHICLE 373 • Mix a minimum solution of 50% HOAT engine coolant Adding Coolant Your vehicle has been built with an improved engine and distilled water. Use higher concentrations (not to coolant (antifreeze) that allows extended maintenance exceed 70%) if temperatures below 34°F ( 37°C) are intervals.
Page 376
374 MAINTAINING YOUR VEHICLE Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent the loss of • Do not use a pressure cap other than the one engine coolant (antifreeze), and to ensure that the engine specified for your vehicle.
Page 377
MAINTAINING YOUR VEHICLE 375 Coolant Level Points To Remember The coolant recovery bottle provides a quick visual NOTE: When the vehicle is stopped after a few miles method for determining that the engine coolant (anti- (kilometers) of operation, you may observe vapor coming freeze) level is adequate.
376 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are result in unsatisfactory engine coolant (antifreeze) required, or if the level in the coolant recovery bottle performance, poor gas mileage, and increased does not drop when the engine cools, the cooling emissions.
Page 379
MAINTAINING YOUR VEHICLE 377 WARNING! WARNING! (Continued) • To avoid contamination from foreign matter or • Use only manufacturer’s recommended brake moisture, use only new brake fluid or fluid that fluid. Refer to “Fluids, Lubricants, and Genuine has been in a tightly closed container. Keep the Parts”...
378 MAINTAINING YOUR VEHICLE Special Additives WARNING! (Continued) Automatic Transmission Fluid (ATF) is an engineered • Do not allow petroleum based fluid to contami- product and its performance may be impaired by supple- nate the brake fluid. Brake seal components could mental additives.
Page 381
MAINTAINING YOUR VEHICLE 379 Fluid Level Check 5. Remove the dipstick, wipe it clean and reinsert it until Check the fluid level while the transmission is at normal seated. operating temperature 180° F (82° C). This occurs after at 6. Remove the dipstick again and note the fluid level on least 15 miles (24 km) of driving.
Page 382
380 MAINTAINING YOUR VEHICLE (upper) reference holes when the transmission reaches CAUTION! 180° F (82° C). Remember it is best to check the level at • Do not use chemical flushes in your transmission the normal operating temperature. as the chemicals can damage your transmission CAUTION! components.
MAINTAINING YOUR VEHICLE 381 Transfer Case Front/Rear Axle Fluid Inspect the transfer case for fluid leaks. If a fluid leak is For normal service, periodic fluid level checks are not evident the transfer case fluid level may be low. Have the required.
382 MAINTAINING YOUR VEHICLE axle fluid level should be 1/8 in (3 mm) below bottom of passable in snow and ice, and those that are sprayed on filler plug for 8-1/4 in, and 9-1/4 in axles. trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 385
MAINTAINING YOUR VEHICLE 383 • Insects, tree sap and tar • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint • Salt in the air near seacoast localities finish. • Atmospheric fallout/industrial pollutants CAUTION! Washing •...
Page 386
384 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, Wheel And Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and considered the responsibility of the owner. chrome-plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 387
MAINTAINING YOUR VEHICLE 385 • For tough stains, apply MOPAR Total Clean or if absolutely necessary. Do not use harsh cleaners or equivalent or a mild soap solution to a clean, damp Armor All . Use MOPAR Total Clean or equivalent to cloth and remove the stain.
Page 388
386 MAINTAINING YOUR VEHICLE your leather upholstery. Application of a leather condi- Cleaning Plastic Instrument Cluster Lenses tioner is not required to maintain the original condition. The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care WARNING! must be taken to avoid scratching the plastic.
MAINTAINING YOUR VEHICLE 387 Replace the belts if they appear frayed or worn, or if the buckles do not work properly. FUSES Underhood Fuses (Power Distribution Center) Your vehicle is equipped with an electrical power distri- bution center located on the left side of the engine compartment.
Page 390
388 MAINTAINING YOUR VEHICLE Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse Spare 2 Amp Run/Start Ignition Gray Switch Spare 10 Amp AC Clutch 30 Amp Electric Brake Pink 15 Amp Trailer Tow Lt Stop/ 50 Amp Power Seat Blue Turn...
392 MAINTAINING YOUR VEHICLE • Anytime you store your vehicle, or keep it out of LIGHT BULBS – Exterior Bulb No. service (i.e. vacation) for two weeks or more, run the Headlamp ......H13 air conditioning system at idle for about five minutes Front Park/Turn/Side Marker .
Page 395
MAINTAINING YOUR VEHICLE 393 5. Twist 1/4-turn and remove headlamp bulb from hous- ing and replace. 3. Grasp the headlamp and pull firmly to disengage the headlamp housing from the fender panel. NOTE: The headlamp bulb is a halogen bulb. Take care 4.
394 MAINTAINING YOUR VEHICLE To remove the park/turn signal bulb, rotate bulb socket Rear Side Marker, Taillamps/Stop Lamps, And 1/4-turn and remove socket from housing. Pull bulb Turn Signal Bulbs straight from socket. 1. Remove the two screws that pass through the bed sheet metal.
Page 397
MAINTAINING YOUR VEHICLE 395 2. Pull the taillamp housing straight out from the body. 3. Rotate the bulb socket counterclockwise to remove it from the housing.
Page 398
396 MAINTAINING YOUR VEHICLE 4. Pull bulb straight out of socket. 5. Reverse this procedure to install bulb and housing. Place the two raised blocks past the body.
MAINTAINING YOUR VEHICLE 397 Center High-Mounted Stop Lamp And Cargo 2. Remove housing from the cab. Lamp 1. Remove the two screws holding the housing/lens to the body, as shown.
Page 400
398 MAINTAINING YOUR VEHICLE 3. Remove connector from housing tab for more clear- 4. Turn desired bulb socket 1/4-turn and remove socket ance. and bulb from housing.
MAINTAINING YOUR VEHICLE 399 5. Pull desired bulb straight from the socket. License Lamps 1. Using a screwdriver, pry black rubber housing from the bumper. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mounted Stop Lamp 6. Reverse this procedure for installation of bulbs and housing.
Page 402
400 MAINTAINING YOUR VEHICLE 2. Rotate the socket 1/4-turn counterclockwise. 3. Pull bulb from socket.
MAINTAINING YOUR VEHICLE 401 4. Reverse this procedure for installation. 2. Rotate the bulb 1/4-turn counterclockwise and pull to remove from the fog lamp housing. Fog Lamps 3. Reverse procedure to install. 1. Disconnect connector from the fog lamp by raising the wire harness lock tab and pulling on wire harness connector.
402 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 408
406 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Based on engine operation conditions the oil change The Scheduled Maintenance services listed in this indicator message will illuminate, this means that service manual must be done at the times or mileages specified is required for your vehicle. Have your vehicle serviced to protect your vehicle warranty and ensure the best as soon as possible, within the next 500 miles (805 km).
Page 409
MAINTENANCE SCHEDULES 407 • Check the windshield washer solvent and add if Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a required. scheduled oil change is performed by someone other Once A Month than your authorized dealer, the message can be reset by •...
Page 410
408 MAINTENANCE SCHEDULES At Each Oil Change Required Maintenance Intervals • Change the engine oil filter. NOTE: ** Vehicles built with the 4.7L engine are equipped with sixteen spark plugs. One set is located on • Inspect the brake hoses and lines. the top of the engine under the coils and the second set is located on the side of the engine.
Page 411
MAINTENANCE SCHEDULES 409 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
410 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 413
MAINTENANCE SCHEDULES 411 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 414
412 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 64,000 Miles (104,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 415
MAINTENANCE SCHEDULES 413 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 416
414 MAINTENANCE SCHEDULES 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer Reading Date Repair Order #...
Page 417
MAINTENANCE SCHEDULES 415 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏...
Page 418
416 MAINTENANCE SCHEDULES 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 419
MAINTENANCE SCHEDULES 417 120,000 Miles (195,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏...
Page 420
418 MAINTENANCE SCHEDULES 128,000 Miles (208,000 km) or 96 Months Maintenance Service 136,000 Miles (221,000 km) or Schedule 102 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 421
MAINTENANCE SCHEDULES 419 144,000 Miles (234,000 km) or 108 Months Maintenance Service 152,000 Miles (247,000 km) or Schedule 114 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 422
420 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Suggestions For Obtaining Service For Your Vehicle......423 Speech Impaired (TDD/TTY) .
Page 424
422 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 429 Department Of Transportation Uniform Tire Quality Grades ......429 ▫...
IF YOU NEED CONSUMER ASSISTANCE 423 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
424 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (866) 726–4636 •...
IF YOU NEED CONSUMER ASSISTANCE 425 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
426 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
IF YOU NEED CONSUMER ASSISTANCE 427 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 430
428 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles.
Page 431
IF YOU NEED CONSUMER ASSISTANCE 429 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 432
430 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 451
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 452
Chrysler Group LLC 11ND33-126-AG Seventh Edition Printed in U.S.A.