Dodge dakota 2002 Service Manual page 274

DR
CLUTCH
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DIAGNOSIS AND TESTING
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . 6
CLUTCH DISC
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CLUTCH HOUSING
DIAGNOSIS AND TESTING
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 10
CLUTCH RELEASE BEARING
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 11
CLUTCH
DESCRIPTION
The clutch mechanism consists of a flywheel, a sin-
gle, dry-type disc, and a diaphragm style clutch cover
(Fig. 1). A hydraulic linkage is used to operate the
clutch release bearing and fork. The flywheel is
bolted to the rear flange of the crankshaft. The
clutch pressure plate is bolted to the flywheel with
the clutch disc located between these two compo-
nents. The clutch system provides the mechanical,
but still easily detachable, link between the engine
and the transmission. The system is designed to
ensure that the full torque output of the engine is
transfered to the transmission while isolating the
transmission from the engine firing pulses to mini-
mize concerns such as gear rattle.
OPERATION
Leverage, clamping force and friction are what
make the clutch work. The disc serves as the friction
element and a diaphragm spring and pressure plate
provide the clamping force. The clutch pedal, hydrau-
lic linkage, release lever and bearing provide the
leverage.
The clutch master cylinder push rod is connected
to the clutch pedal. When the clutch pedal is
depressed, the slave cylinder is operated by the
clutch master cylinder mounted on the dash panel.
The release fork is actuated by the hydraulic slave
cylinder mounted on the transmission housing. The
CLUTCH
TABLE OF CONTENTS
page
. . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . 8
FLYWHEEL
DIAGNOSIS AND TESTING
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 12
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 12
PILOT BEARING
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 12
LINKAGE
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 13
CLUTCH PEDAL POSITION SWITCH
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 14
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DIAGNOSIS AND TESTING . . . . . . . . . . . . . . . . 14
Fig. 1 ENGINE POWERFLOW
release bearing is operated by a release fork pivoting
on a ball stud mounted in the transmission housing.
The release bearing then depresses the pressure
plate spring fingers, releasing pressure on the clutch
disc and allowing the engine crankshaft to spin inde-
pendently of the transmission input shaft (Fig. 2).
CLUTCH 6 - 1
page
. . . . . . . . . . . . . . . . 11