6-3) Memory Switch Functions Table - SunStar SPS/E-BS1201H User Manual

6-3) Memory Switch Functions Table

(1) General sewing functions (A Group)
Turn on the power pressing
No. Functions and Description
A-01 Setting maximum sewing speed
A-02 Setting speed for the first 1-5 stitches
(Softstart function, different by type)
Setting pattern data calling
A-03
(You can set for each pattern)
Setting display and change possibility of X,Y scale
A-04
rate and maximum speed limit (prevent errors or mistakes)
Setting counter function
A-05 Production counter : addition count
Lower thread counter : reduction count
A-06 Setting center point for scale
Setting whether to search original point after sewing
A-07
(sewing with ordinary pattern number)
Setting whether to search original point after sewing
A-08
(sewing with function combination)
A-09 Setting drive scope to infinite
A-10 Setting starting angel for X, Y drive
A-11 Setting trimming speed
A-12 Setting reverse rotation after trimming
A-13 Setting angle for reverse rotation after trimming
A-14 Setting whether to use electronic wiper
A-15 Faster moving of presser foot after trimming
Setting search for original point after certain amount of sewing
A-16
(after amount set in A-17)
A-17 Number of automatic search for original point
A-18 Time for electronic wiper ON
A-19 Canceling trimming
A-20 Time for solenoid 0 full on (clamp solenoid)
A-21 Time for solenoid 1 full on (trimming solenoid)
A-22 Time for solenoid 2 full on (sub solenoid 2)
A-23 Time for solenoid 3 full on (sub solenoid 3)
A-24 Solenoid 0 duty (clamp solenoid)
A-25 Solenoid 1 duty (trimming solenoid)
A-26 Solenoid 2 duty (sub solenoid 2)
A-27 Solenoid 3 duty (sub solenoid 3)
A-28 Delay time for clamp solenoid moving up
A-29 Delay time for clamp solenoid moving down
A-30 Setting OFF time for electronic wiper
A-31 Setting whether clamp moves up/down after mid trimming
A-32 Setting pneumatic thread holder
Setting integrated/separated pedal
A-33
(For pneumatic only. Others have integrated pedals)
A-34 Setting whether to use pin hole device
A-35 Setting whether to use head open/close
A-36 Whether to use upper stop when turn power on
A-37 Set time for AC off checking
A-38 Set time for voltage overload checking
26
and . Turn on the memory switch pressing
General:
Heavy:
Light:
Knitwear:
Buttons:
Hole fixing :
1st stitch: 400~900
2nd stitch: 400~2,000
3rd stitch: 400~2,000
4th stitch: 400~2,000
5th stitch: 400~2,000
0 : calling impossible
1 : calling possible
0 : change impossible
1 : change possible
0 : production counter
1 : lower thread counter
0 : original point
1 : sewing start point
0 : OFF
1 : ON
0 : OFF
1 : ON
0 : Infinite
1 : limited
–100 ~ 100°
200 ~ 400spm
0 : OFF, 1 : ON
0~70°
0 : OFF
1 : ON
0 : OFF, 1 : ON
0 : OFF
1 : ON
0~1000
4~1024 ms
0 : trim ON
1 : trim OFF
4~72 ms
4~1020 ms
4~1020 ms
4~1020 ms
10~25%
10~25%
10~25%
10~25%
-
4~1020 ms
0 : Down, 1 : Up
0 : OFF, 1 : ON
-
0 : OFF
1 : ON
0 : OFF
1 : ON
0 : OFF
1 : ON
4 ~ 48 [ms]
4 ~ 1024 [ms]
P1 .
Scope
100~3,200
100~3,200
100~2,700
100~2,700
100~2,700
100~3,200
1201
1~22 : 1
23~99 : 0
Belt type : –24° , Direct : –24°
1201, 1202
0
Others
40 ms
Others
0
Only in Direct type
Only in Direct type
Default Unit
2,700 spm
2,700 spm
2,300 spm
2,300 spm 100spm
2,300 spm
2,700 spm
400 spm
900 spm
2,300 spm 100spm
2,300 spm
2,300 spm
1202 1254
1~33 : 1 1~56 : 1
34~99 : 0 57~99 : 0
1
0
0
0
0
1
1°
400 spm 100spm
0
0° 1°
1254
1
1
0
1000 4
100 ms 4 ms
0
52 ms 4 ms
100 ms 4 ms
100 ms 4 ms
100 ms 4 ms
10% 1%
20% 5%
20% 5%
20% 5%
- -
Hole fix device
4 ms
100 ms
1
0
-
Hole fix device
1
1
1
20 ms
20 ms