Failover/Failback - Panasonic TH-55VF1HU Operating Informations

[1st search input], [2nd search input]
Set the input to search when [Custom] is selected.
[HDMI] / [DisplayPort] / [DIGITAL LINK] / [DVI-D1] /
[DVI-D2] / [PC] / [COMPONENT]* / [VIDEO] / [USB] /
[(None)]
: [COMPONENT] may be displayed as [RGB]
*
depending on the settings of [Component/RGB-in
select]. (see page 51)
[HDMI], [DIGITAL LINK], [DVI-D1], [DVI-D2], [PC]
Sets the input for signal detection during [Input
detection].
[Off]: Signal detection is not performed for the set
input.
[On]: Signal detection is performed for the set input.
[Changing delay]
Sets the delay time until the input is switched during
[Input detection].
[Off]: Switches the input if a signal is interrupted
even for a very short period.
1 ‒ 10:
Sets the delay time (sec.).
Switches the input when the set time has
elapsed after detecting no signal is present.
However, if the detection period during which
no signal is present is shorter than the set
delay time, the input is not switched.
Note
●
With the USB input, the unit determines no signal is
present when the USB memory is not connected to
the USB terminal.
In addition, even when a USB memory is
connected, if there is no playable file, the unit
determines no signal is present.
● This menu will be greyed out and cannot be set
under the following conditions.
[Input lock] is not set to [Off]. (see page 79)
•
[Failover/Failback] - [Input change mode] is not set
•
to [Off]. (see page 59)
● If the input is changed by this function, the last input
is selected when the power is turned on next time.
If you wish to retain the original input when the
power is turned on, set [Initial input] to the original
input. (see page 79)
●
[Input detection] is the function that automatically
switches the input as below by monitoring the
presence of signal for the set input.
If a video signal is input to the set input that is
•
not displayed (When the status has changed
from signal absent to signal present.), the input
is selected and switched.
If no signal is detected for the displayed input,
•
the setting switches to the set input to which a
signal is input. Also, if no signal is present for
the displayed input when the power is turned
on or when the input is switched, the setting
switches to the set input to which a signal is
input. When signals are input to multiple set
inputs, the priority order as default (immediately
after power-on) is as follows: HDMI, DIGITAL
LINK, DVI-D1, DVI-D2, PC.
In the other case (When the input is switched
after power-on), the input displayed last takes
priority.
●
[Changing delay] is the function to prevent the
accidental input switch during a short period,
such as when the signal is interrupted due to the
frequency change for the input signal while [Input
detection] is operating.
If a signal is detected again within the set period
(sec.), the input is not switched.
● [Input detection] may not operate correctly
depending on the image playback device.
● [Input detection] may not operate correctly when
connected with the DIGITAL LINK daisy chain.

Failover/Failback

Automatically switches to the backup input video if an
interruption of video occurs.
[Input change mode]
[Off]:
Disables the Backup Input function.
Failover/Failback
Input change mode
[Quick]:
Promptly switches to the backup input (Failover)
or puts back to the original input (Failback) if an
interruption of video occurs.
The backup video signal needs to be in the same
format as the (main) input in use for viewing.
Upon switching to the backup input, the video and
audio adjustment values for the (main) input used
for viewing will be inherited.
Failover/Failback
Input change mode
Primary backup input
Secondary backup input
Auto switch back mode
Changing mode
Backup input change
Main input
Current input
[Normal]:
Promptly switches to the backup input or puts
back to the original input if an interruption of video
occurs.
The backup video signal does not need to be in the
same format as the (main) input in use for viewing.
Upon switching to the backup input, the video and
audio adjustment values for the backup input will
be used.
Off
Quick
HDMI
DVI-D1
Disable
High speed
Active
DVI-D2
Main input
English
59