Mitsubishi Electric F700 Instruction Manual page 116

Function assignment of external
terminal and control
Setting
Signal
Positive Negative
Name
Logic Logic
14 114 FDN
15 115 FUP
16 116 RL

17 MC1

18 MC2

19 MC3
25 125 FAN
26 126 FIN
45 145 RUN3
46 146 Y46
47 147 PID
64 164 Y64
70 170 SLEEP
90 190 Y90
91 191 Y91
92 192 Y92
93 193 Y93
94 194 ALM2
95 195 Y95
96 196 REM
98 198 LF
99 199 ALM

9999
*1 Note that when the frequency setting is varied using an analog signal or
frequency) signal may alternate on and off depending on that varying speed and the timing of the varying speed due to acceleration/
deceleration time setting. (The output will not alternate on and off when the acceleration/deceleration time setting is "0s".)
*2 When a power supply reset is performed, the alarm output 2 signal (ALM2) turns off as soon as the power supply switches off.
108
Function
Output when the feedback value falls below
PID lower limit
the lower limit of PID control.
Output when the feedback value rises above
PID upper limit
the upper limit of PID control
PID forward/reverse Output when forward rotation is performed in
rotation output PID control.
Commercial power-
supply switchover MC1
Commercial power- Used when the commercial power supply-
supply switchover MC2 inverter switchover function is used.
Commercial power-
supply switchover MC3
Fan fault output Output at the time of a fan fault.
Output when the heatsink temperature
Heatsink overheat
reaches about 85% of the heatsink overheat
pre-alarm
protection providing temperature.
During inverter
Output when the inverter running and start
running and start
commands are on.
command is on
During deceleration at
occurrence of power Output when the power failure-time
failure (retained until deceleration function is executed.
release)
During PID control
Output during PID control.
activated
During retry Output during retry processing.
PID output Output when the PID output interruption
interruption function is executed.
Output when any of the control circuit
capacitor, main circuit capacitor and inrush
Life alarm
current limit circuit or the cooling fan
approaches the end of its service life.
Alarm output 3 Output when an error occurs due to the circuit
(power-off signal) failure or connection alarm of the inverter.
Turned on and off alternately every time the
Power saving power saving average value is updated
average value when the power saving monitor is used.
updated timing Cannot be set to Pr. 195 and Pr. 196 (relay
output terminal).
Average current value and maintenance
Current average timer value are output as pulses.
value monitor signal Cannot be set to Pr. 195 and Pr. 196 (relay
output terminal).
Output when the inverter's protective
function is activated to stop the output
Alarm output 2 (major fault). Continue outputting the signal
during inverter reset and stop outputting
after reset is cancelled.
Maintenance timer Output when Pr. 503 rises to or above the Pr.
signal 504 setting.
Output to the terminal when a value is set to
Remote output
the parameter.
Output when a minor fault (fan failure or
Minor fault output
communication error warning) occurs.
Output when the inverter's protective function is
Alarm output activated to stop the output (major fault). The
signal output is stopped when a reset turns on.

No function
Operation
*2
of the operation panel (FR-DU07), the output of the SU (up to
Related Refer
Parameters to Page
Pr. 127 to Pr. 134,
201
Pr. 575 to Pr. 577
Pr. 135 to Pr. 139,
209
Pr. 159
Pr. 244 216

242

109
Pr. 261 to Pr. 266 130
Pr. 127 to Pr. 134,
201
Pr. 575 to Pr. 577
Pr. 65 to Pr. 69 132
Pr. 127 to Pr. 134,
201
Pr. 575 to Pr. 577
Pr. 255 to Pr. 259 217

110
Pr. 52, Pr. 54,
Pr. 158, Pr. 891 to 137
Pr. 899
Pr. 555 to Pr. 557 220

109
Pr. 503, Pr. 504 219
Pr. 495 to Pr. 497 114
177,
Pr. 121, Pr. 244
216

109
 