Symmetricom TimeProvider 100 Manuals

Manuals and User Guides for Symmetricom TimeProvider 100. We have 1 Symmetricom TimeProvider 100 manual available for free PDF download: User Manual

Symmetricom TimeProvider 100 User Manual

Symmetricom TimeProvider 100 User Manual (124 pages)

GPS Timing and Frequency Source Device

Brand: Symmetricom | Category: Clock | Size: 1.78 MB

Table of Contents

Table of Contents
3
Purpose of this Guide
13
Conventions Used in this Guide
14
Warnings, Cautions, Recommendations, and Notes
15
Related Documents and Information
16
Timeprovider 100
17
Overview
17
Chapter 1 Overview

18
Chapter 2 Installation

25
- Unpack the Unit
  27
- Location of Timeprovider 100 Product Label
  28
- Rack Mounting the Timeprovider 100
  28
- Universal Ground Symbol
  29
- Ground the Shelf
  29
- Configuration Setup
  30
  - Apply Power
    30
  - Establish Serial Communication
    31
  - COM Port Properties
    31
  - Log on to Timeprovider 100
    32
  - Check GPS Status
    33
  - Check Inventory Information
    33
  - Configure the Timeprovider 100 IP Address
    33
  - Confirm Timeprovider 100 Network Communication
    36
  - Configure Frequency Outputs
    37
  - Signal Types
    37
  - Signal Type Selection Choices
    38
- Installation and Configuration Checklist
  39
- Installation and Configuring Checklist
  39
Chapter 3 Part Numbers and Return Information

41
- Timeprovider 100 System and Accessory Part Numbers
  41
- Returning the Timeprovider 100
  41
  - Component Part Numbers
    41
  - Equipment Return Procedure
    42
  - Repacking the Unit
    42
Chapter 4 Operations

43
- Introduction
  43
- RTE Clock Modes
  44
- Timeprovider 100 Clock Modes
  44
- Alarms & Events
  45
  - Level
    45
  - State
    46
  - Delay
    46
  - Transient
    46
  - Timeprovider 100 Alarms, Events, and Configuration
    46
- Alarm Levels
  48
- Alarm Levels
  49
- Date & Time
  50
- Timeprovider 100 Logs
  50
  - Event Log
    50
  - Command Log
    50
- User Sessions
  51
- System Configurations
  51
Chapter 5 CLI Commands

53
- Overview
  53
- Timeprovider 100 CLI Command Set
  56
  - Command User Levels
    56
- Command Groups
  57
  - Cli-Settings
    58
  - Ping
    59
  - Switchfirmware
    59
  - Logout
    59
  - Reboot
    60
  - Upgrade
    60
- Show Commands
  61
  - Show Active_Alarm
    61
  - Show Alarmconf
    62
  - Show Clock
    62
  - Show Eia232
    62
  - Show Gps
    63
  - Show Image
    63
  - Show Inventory
    64
  - Show Ipconfig
    64
  - Show Ipstatus
    64
  - Show Log
    65
  - Show Event Log
    66
  - Show Command Log
    67
  - Show Output
    67
  - Show Snmp
    68
  - Show Status
    69
  - Show Users
    69
- Set Commands
  70
  - Set Alarmconf
    71
  - Set Clock
    72
  - Set Configuration
    72
  - Set Gps
    74
  - Set Ipconfig
    76
  - Set Output
    79
  - Set Password
    82
  - Set Snmp
    83
  - Set User
    83
Chapter 6 Maintenance and Troubleshooting

87
- Preventive Maintenance
  87
- Safety Considerations
  88
- Reading LED Conditions
  88
- LED Conditions
  88
- Upgrading the Firmware
  89
- Contacting Technical Support
  91
Appendix A System Messages

93
- System Messages
  93
- Alarms and Event System Messages
  93
Appendix B Specifications and Factory Defaults

97
- Component Specifications
  97
  - Mechanical
    97
  - Timeprovider 100 Mechanical Specifications
    97
  - Environmental
    98
  - Transportation
    98
  - Operations
    98
  - Timeprovider 100 Environmental Specifications
    98
  - Timeprovider 100 Transportation Specifications
    98
  - Timeprovider 100 Operations Specifications
    98
  - Power
    99
  - GPS Antenna Interface
    99
  - Timeprovider 100 Power Specifications
    99
  - GPS Antenna Specifications
    99
  - Serial Port Interface
    100
  - Ethernet Port
    100
  - Serial Port Specifications
    100
  - LAN Port Specifications
    100
  - 10Mhz Analog Output
    101
  - 10Mhz Analog Output Specifications
    101
  - PPS Output
    102
  - E1 Outputs
    102
  - PPS Output Specifications
    102
  - E1 Output Specifications
    102
- Factory Defaults
  104
- General and Communication Parameters
  104
- Electromagnetic Environment
  105
- Regulatory Requirements
  105
Appendix C Installing the GPS Antenna

107
- Antenna Kits and Accessories
  107
  - Selecting the Proper Gain Antenna
    107
  - GPS Antennas with Internal LNA
    108
  - Specifications for GPS Antennas
    108
  - L1 GPS Antenna Accessory Kit
    109
  - Transient Eliminators
    110
  - GPS L1 Inline Amplifier
    110
  - FCC-250B-90-1.5NFNF Specifications
    110
  - GPS L1 Inline Amplifier Specifications
    110
  - Antenna Coaxial Cables
    111
  - Antenna Cable Specifications
    111
- Installing Antennas
  112
  - Antenna Connection Overview
    112
  - Planning the Installation
    112
  - Locating the GPS Antenna
    113
  - Antenna Installation Tools and Materials
    115
  - Cutting Antenna Cables
    116
  - Installing the Antenna
    116
  - Connecting the Cable to the Antenna
    117
  - GPS Antenna Installation
    117
  - Installing the Transient Eliminator
    118
  - Installing the Antenna Cable
    119
  - Connecting the GPS Antenna
    119
  - Antenna Installation Completeness Checklist
    119
- Technical Support
  120
Index

121
- Revision a – March
  122

Advertisement

Advertisement

Related Products

Symmetricom Categories

Test Equipment Clock Amplifier Server

GPS

More Symmetricom Manuals