Lexmark MS810 Series User Manual page 358

Index
printer control panel, virtual
display
using the Embedded Web
Server 117
printer hard disk
disposing of 77, 123, 171
encrypting 79, 125, 173
installing 22
removing 26
wiping 79, 125, 173
printer hard disk
encryption 79, 125, 173
printer hard disk memory
erasing 79, 125, 173
printer information
where to find 7
printer IP address
finding 87, 134
printer is printing blank pages 323
printer messages
[x]‑page jam, clear manual feeder.
[250] 272
[x]‑page jam, lift front cover to
remove cartridge. [200–
201] 264
[x]‑page jam, open tray [x].
[24x] 271
[x]‑page jam, open upper and
lower rear door. [231–234] 267
[x]‑page jam, open upper rear
door. [202] 266
[x]‑page jam, remove paper, open
expander rear door. Leave paper
in bin. [41y.xx] 278
[x]‑page jam, remove paper, open
finisher rear door. Leave paper in
bin. [451] 277
[x]‑page jam, remove paper, open
mailbox rear door. Leave paper
in bin. [43y.xx] 280
[x]‑page jam, remove paper, open
stapler door. Leave paper in bin.
[455–457] 273
[x]‑page jam, remove standard bin
jam. [203] 270
[x]‑page jam, remove tray 1 to
clear duplex. [235–239] 270
Cartridge low [88.xy] 282
Cartridge nearly low [88.xy] 282
Cartridge very low, [x] estimated
pages remain [88.xy] 282
Change [paper source] to [custom
string] load [orientation] 282
Change [paper source] to [custom
type name] load
[orientation] 282
Change [paper source] to [paper
size] load [orientation] 283
Change [paper source] to [paper
type] [paper size] load
[orientation] 283
Check tray [x] connection 283
Close door or insert cartridge 283
Close rear door 284
Complex page, some data may not
have printed [39] 284
Configuration change, some held
jobs were not restored [57] 284
Defective flash detected [51] 284
Disk must be formatted for use in
this device 284
Disk near full. Securely clearing
disk space. 284
Empty the hole punch box 285
Error reading USB drive. Remove
USB. 285
Error reading USB hub. Remove
hub. 285
Imaging unit low [84.xy] 285
Imaging unit nearly low
[84.xy] 285
Imaging unit very low, [x]
estimated pages remain
[84.xy] 285
Incompatible output bin [x]
[59] 285
Incompatible tray [x] [59] 286
Incorrect paper size, open [paper
source] [34] 286
Insert hole punch box 286
Insert staple cartridge 286
Insert Tray [x] 286
Install bin [x] 287
Install Tray [x] 287
Insufficient memory for Flash
Memory Defragment operation
[37] 287
Insufficient memory to collate job
[37] 288
Insufficient memory to support
Resource Save feature [35] 288
Insufficient memory, some Held
Jobs were deleted [37] 287
Insufficient memory, some held
jobs will not be restored
[37] 288
Load [paper source] with [custom
string] [paper orientation] 288
Load [paper source] with [custom
type name] [paper
orientation] 289
Load [paper source] with [paper
size] [paper orientation] 289
Load [paper source] with [paper
type] [paper size] [paper
orientation] 289
Load manual feeder with [custom
string] [paper orientation] 289
Load manual feeder with [custom
type name] [paper
orientation] 290
Load manual feeder with [paper
size] [paper orientation] 290
Load manual feeder with [paper
type] [paper size] [paper
orientation] 290
Load staples 288
Maintenance kit low [80.xy] 290
Maintenance kit nearly low
[80.xy] 290
Maintenance kit very low, [x]
estimated pages remain
[80.xy] 291
Memory full [38] 291
Network [x] software error
[54] 291
Not enough free space in flash
memory for resources [52] 291
Paper changes needed 292
Parallel port [x] disabled [56] 292
PPDS font error [50] 292
Reattach bin [x] 292
Reattach bins [x] – [y] 293
Reinstall missing or unresponsive
cartridge [31.xy] 293
Reinstall missing or unresponsive
imaging unit [31.xy] 294
Remove defective disk [61] 294
Remove packaging material, [area
name] 294
Remove paper from [linked set bin
name] 294
Remove paper from all bins 294
Remove paper from bin [x] 294
358