System Maintenance Menu (For Maintenance Personnel) - Oki C310dn Maintenance Manual

Oki Data CONFIDENTIAL

5.1 System Maintenance menu (for maintenance personnel)

By turning on each printer while holding down
started. The menu is displayed only in English irrespective of the destination of the printer.
Note: The menu allows for changes such as the printer's destination changes, and is
transparent to end-users of the printer.
Table 5-1: Maintenance menu display table
Value
Category Item (1st Line)
(2nd Line)
SYSTEM ENTER ****** ****** 000
MAINTE PASSWORD
OKIUSER OKIUSER ODA
OEL
APS
JP1
JPOEM1
OEMA
OEML
MAINTE-
NANCE
MENU
SD CARD EXECUTE
FORMAT
(Only C530)
FLASH EXECUTE
FORMAT
MENU RESET EXECUTE
44346001TH Rev.1
and , its System Maintenance menu is
DF Function
Enters a password to enter the System
000 Maintenance menu. The default for this item is
000000. Six to 12 alphanumeric characters can
be entered for the item.
Sets a destination.
* JPOEM1: OEM in Japan
OEMA: A4-default Overseas OEM
OEML: Letter-default Overseas OEM
The printer automatically reboots after this
menu is exited.
Display condition:
The security SD card function is disabled.
- Initializes an SD card. When executed, this
menu is exited and starts initializing an SD card.
Display condition:
The printer has the SD card installed on it
(ADMIN MENU-FILE SYS MAINTE-SD CARD
is set to ENABLE).
- Displays the following confirmation message in
response to the press of the OK button:
ARE YOU SURE?
YES/NO
NO restores the previous menu display when
selected. When selected, YES exits this menu,
starting formatting the installed resident (on-
board) flash device.
* Never use this item.
- Resets the information in the EEPROM to
factory default settings. The printer automatically
reboots after change to the default settings.
* This does not initialize some special items.
Value
Category Item (1st Line)
(2nd Line)
CONFIG CODESET TYPE1
MENU TYPE2
TEST TEST PRINT ENABLE
PRINT MENU DISABLE
MENU
FUSE FUSE KEEP EXECUTE
KEEP MODE
MODE
PERSON- IBM 5577 ENABLE
ALITY DISABLE
(Only
IBM PPR III XL ENABLE
C530dn)
DISABLE
EPSON FX ENABLE
DISABLE
HP-GL/2 ENABLE
5. MAINTENANCE MENUS
DF Function
Displayed for all the destinations of the printer.
* TYPE1: Disables Russian, Grease and
Bulgarian (language file downloading). This
value uses English for the operator panel
language when the printer already has any of
the three languages downloaded.
TYPE2: Enables Russian, Grease and
Bulgarian.
The printer automatically reboots after this
menu is exited. The default for this item is
TYPE2 when the printer's destination is OEL/
APS/OEMA, and TYPE1 when it is not OEL/
APS/OEMA.
Sets whether or not to display PRT CHK PATN
* and ENG STATUS PRINT in the USER MENU-
PRINT INFORMATION category. This item
always does not display PRT ID CHK PATN or
ENG STATUS PRINT when set to DISABLE.
When this menu is exited after change of the
setting for the item, the printer restarts.
- Places the printer online after a command is
issued from the CU to PU by pressing the OK
button. With the printer turned on, consumables
of the printer can be replaced with new ones,
and then the printer can be checked for proper
operation (where, not breaking the new ones'
fuses, the printer adds no operation counts
to the life of the consumables replaced with
the new ones). Turning off the printer ends the
check mode. Turning it on next time disables the
mode.
Does not allow USER MENU-SYS CONFIG
* MENU-PERSONALITY to display PDL
languages for which DISABLE is set with
*
this menu. When receiving print data in such
languages, the printer displays INVALID
* DATA, discarding the data. When the printer's
destination is Japan and IBM PPR III XL and
EPSON FX is set to ENABLE, no operation of
the printer is assured.
88 /