Nat Enable - THOMSON 516 Reference Manual

nat enable

Enable NAT/PAT on a SpeedTouch
SYNTAX:
nat enable addr = <ip-address>
[type = <{none | pat}>]
where:
addr The IP address to use for outgoing address translation. Must be one of the own IP
addresses of the SpeedTouch
Tip Use the command :ip aplist to obtain a list of all configured IP addresses.
type Enable port translation (pat) or not (none).
EXAMPLE:
=>ip aplist
1 eth0 Type:Ethernet
inet addr:10.10.10.147
UP RUNNING
IPRX bytes:19791886
IPTX bytes:839550
HWRX bytes:0
HWTX bytes:0
0 loop Type:0
inet addr:127.0.0.1
UP RUNNING
IPRX bytes:116
IPTX bytes:0
HWRX bytes:0
HWTX bytes:0
=>nat enable addr=10.10.10.147 type=pat
=>ip aplist
1 eth0 Type:Ethernet
inet addr:10.10.10.147
UP RUNNING pat
IPRX bytes:19791886
IPTX bytes:839550
HWRX bytes:0
HWTX bytes:0
0 loop Type:0
inet addr:127.0.0.1
UP RUNNING
IPRX bytes:116
IPTX bytes:0
HWRX bytes:0
HWTX bytes:0
=>
RELATED COMMANDS:
nat disable
E-DOC-CTC-20040907-0010 v1.0
TM
IP address.
TM
.
HWaddr 00:80:9f:24:ab:cf
Bcast:10.10.10.255
MTU:1500 ReasmMAX:65535
unicastpkts:11341 brcastpkts:290555
unicastpkts:11477 brcastpkts:0
unicastpkts:0 brcastpkts:0
unicastpkts:0 brcastpkts:0
Bcast:127.255.255.255
MTU:1500 ReasmMAX:65535
unicastpkts:0 brcastpkts:2
unicastpkts:0 brcastpkts:0
unicastpkts:0 brcastpkts:0
unicastpkts:0 brcastpkts:0
HWaddr 00:80:9f:24:ab:cf
Bcast:10.10.10.255
MTU:1500 ReasmMAX:65535
unicastpkts:11341 brcastpkts:290555
unicastpkts:11477 brcastpkts:0
unicastpkts:0 brcastpkts:0
unicastpkts:0 brcastpkts:0
Bcast:127.255.255.255
MTU:1500 ReasmMAX:65535
unicastpkts:0 brcastpkts:2
unicastpkts:0 brcastpkts:0
unicastpkts:0 brcastpkts:0
unicastpkts:0 brcastpkts:0
Disable NAT or PAT on the specified SpeedTouchTM IP address.
BRHWaddr ff:ff:ff:ff:ff:ff
Mask:255.0.0.0
Group:2
droppkts:0
droppkts:0
Mask:255.0.0.0
Group:1
droppkts:0
droppkts:0
BRHWaddr ff:ff:ff:ff:ff:ff
Mask:255.0.0.0
Group:2
droppkts:0
droppkts:0
Mask:255.0.0.0
Group:1
droppkts:0
droppkts:0
NAT Commands
REQUIRED
OPTIONAL
257