Xerox DocuPrint N2025 Service Manual page 25

Comments On LIne Message
Tray 2 misfeed with Tray 2 Jam
500 Sheet Feeder Open Tray 2
installed as Tray 2 Lift/Extend MBF
Open Top Cover
Remove PrintCart
Clear Paper Path
Tray 3 Misfeed with Tray 3 Jam
500 Sheet Feeder Open Tray 3
installed as Tray 3 Lift/Extend MBF
Open Top Cover
Remove PrintCart
Clear Paper Path
Tray 2 misfeed with Tray 2 Jam
2000 Sheet Feeder Open Tray 2
installed as Tray 2 Open Rear Trader
Clear Paper Path
Tray 3 misfeed with Tray 3 Jam
2000 Sheet Feeder Open Tray 3
installed as Tray 3 Open Rear TrayDr
Clear Paper Path
Duplex Jam
Open Rear Cover
Clear Paper Path
Jam in the OCT Offset Jam
Open Rear Cover
Open Offset Door
Clear Paper Path
Paper Jam
Open Top Cover
Lift/Extend MBF
Remove PrintCart
Clear Paper Path
Initial Issue
DocuPrint N2025/N2825
Table 1 Error Code Table
Fault History Entry Diagnostic Message
E2-12 E2-1 Misfeed Jam
E2-13 E2-1 Misfeed Jam
E2-12 E2-1 Misfeed Jam
E2-13 E2-1 Misfeed Jam
E2-D E2-2: Misfeed Jam
E8-1 E8-OCT Jam
E1-1 E1: Reg. Jam
02/2000
Error Description
1. Simplex printing: Reg. Sensor is
OFF when the specified time has
passed timing from Feed Roll ON.
2. Printing from 2000 Sheet Feeder:
Reg. Sensor is OFF when the tim-
ing is after receiving Feed_Run sta-
tus.
1. Simplex printing: Reg. Sensor is
OFF when the specified time has
passed timing from Feed Roll ON.
2. Printing from 2000 Sheet Feeder:
Reg. Sensor is OFF when the tim-
ing is after receiving Feed_Run sta-
tus.
1. Simplex printing: Reg. Sensor is
OFF when the specified time has
passed timing from Feed Roll ON.
2. Printing from 2000 Sheet Feeder:
Reg. Sensor is OFF when the tim-
ing is after receiving Feed_Run sta-
tus.
1. Simplex printing: Reg. Sensor is
OFF when the specified time has
passed timing from Feed Roll ON.
2. Printing from 2000 Sheet Feeder:
Reg. Sensor is OFF when the tim-
ing is after receiving Feed_Run sta-
tus.
Registration Sensor did not actuate
within time after the actuation of the
Duplex Motor in reverse.
1. OCT sensor did not actuate within
time after the actutation of the Exit
sensor.
2. OCT sensor is not deactuated
within time after actuation of OCT
Sensor.
3. OCT sensor is actuated at power
on.
1. Registration Sensor did not deactu-
ate within time after actuation of
Registration sensor.
2. Registration sensor is actuated at
power on.
3. Registration is actuated during
warm up cycle or an erase cycle.
2-7
Action
Open Top Cover or Feeder and
remove the sheets. Then close
the cover.
Go to RAP 49
Open Top Cover or Feeder and
remove the sheets. Then close
the cover.
Go to RAP 49
Open Top Cover or Feeder and
remove the sheets. Then close
the cover.
Go to RAP 62
Open Top Cover or Feeder and
remove the sheets. Then close
the cover.
Go to RAP 62
Open Rear Cover and remove
any paper.
Go to RAP 9
Open OCT rear door and
remove any paper.
Open Rear cover and remove
any paper.
Go to RAP 68
Open Top Cover, remove EP
Cartridge, Lift and Extend MBF
assy and remove any paper.
Go to RAP 7
Status Indicator Repair Analysis Procedures
Error Code Table