Upper Display Board - CYBEX Treadmill Owner's Service Manual

Cybex Pro Treadmill Owner's & Service Manual
E. Using a 3/8" nutdriver, secure the one nut over the ground wire terminal.
F. Using a Phillips head screwdriver, secure the switch plate to the
treadmill with the I (on) toward the top.

Upper Display Board

Tools Required
• Phillips head screwdriver
• ESD (Electro Static Discharge) grounding strap
1. Disconnect the external power source.
A. Turn the main power switch on the left side to the off (O) position.
B. Unplug the treadmill from the power outlet.
NOTE: The display board is susceptible to damage from a discharge of static
electricity. While handling parts underneath the console cover use an
ESD grounding strap. This eliminates the potential voltage (static)
difference between you and the equipment you are working on. Wear
an ESD strap for the rest of this procedure.
2. Remove the console from the handrail.
NOTE: If you have a cable plugged into the RJ-45 port disconnect it.
A. Using a Phillips head screwdriver, remove the five screws that hold the
top console back to the console front.
B. Using a Phillips head screwdriver, remove the three screws that hold the
bottom back cover to the console front.
C. Gently pull off the console backs. NOTE: The bottom back will have
delicate wires attached to it. Do not apply pressure to it.
3. Remove the display board.
A. Disconnect these cables from the display board: the display cable (2
connectors), the two upper switch membranes, the lower switch
membrane, the contact heart rate cable and the upper to lower board
jumper. See Figure 19.
B. Using a Phillips head screwdriver, remove the four Phillips head screws
that hold the display board to the console.
C. Gently pull the display board up to disconnect it from the CSAFE board.
Table of Contents . . . . . . . . . . . iii
Important Safety Instructions . . 1-2
Warning Decals. . . . . . . . . . . . . 1-4
Caution Decals . . . . . . . . . . . . . 1-7
Emergency Stop Key (e-stop). . 1-8
2 Technical Specifications
Specifications . . . . . . . . . . . . . . 2-1
3 Operation
Terms & Symbols Used . . . . . . 3-1
Quick Operation Guide . . . . . . 3-2
Detailed Operation Guide . . . . 3-2
Stopping the Treadmill . . . . . . . 3-4
Immobilization Method . . . . . 3-4
Emergency Dismount . . . . . . 3-4
Emergency Stop . . . . . . . . . . . . 3-4
Safety Sentry . . . . . . . . . . . . . . 3-4
Control During Operation . . . . . 3-5
Data Readouts . . . . . . . . . . . . . 3-6
Displaying Heart Rate . . . . . . . . 3-6
Heart Rate LED. . . . . . . . . . . . . 3-7
Use of Programs. . . . . . . . . . . . 3-8
Manual Mode . . . . . . . . . . . . . . 3-9
The Workout Profile . . . . . . . . . 3-9
Meaning of % Grade . . . . . . . . 3-9
Calorie Goal . . . . . . . . . . . . . . 3-10
5K Run . . . . . . . . . . . . . . . . . . 3-12
9 Holes . . . . . . . . . . . . . . . . . . 3-14
Heart Rate. . . . . . . . . . . . . . . . 3-16
Custom Program 1 . . . . . . . . . 3-18
Custom Program 2 . . . . . . . . . 3-20
Create a Custom Program . . . 3-22
4 Preventive Maintenance
Regular Maintenance Activities 4-1
Cleaning Your Treadmill . . . . . . 4-1
Running Belt Maintenance . . . . 4-2
Other Preventive Maintenance . 4-6
Service Schedule . . . . . . . . . . . 4-7
Log Sheet . . . . . . . . . . . . . . . . . 4-8
5 Removal & Replacement
Quick Setup . . . . . . . . . . . . . . . 5-1
Choosing & Preparing a Site . . 5-1
Electrical Power Requirements 5-2
Assembling the Treadmill . . . . . 5-2
Tools Required . . . . . . . . . . . . . 5-2
Testing the Treadmill Operation 5-11
Setting Operation Options . . . 5-12
6 Customer Service
7 Service
Warnings/Cautions . . . . . . . . . . 7-1
Test Mode . . . . . . . . . . . . . . . . . 7-2
LED Functions . . . . . . . . . . . . . 7-3
Key Functions . . . . . . . . . . . . . . 7-3
Error Codes. . . . . . . . . . . . . . . . 7-4
Motor Current & Voltage . . . . . 7-4
Speed Sensor Adjustment . . . . 7-6
Speed Calibration . . . . . . . . . . . 7-8
Running Belt & Deck . . . . . . . . 7-8
Rear Roller . . . . . . . . . . . . . . . . 7-9
Front Roller . . . . . . . . . . . . . . . 7-10
Drive Belt . . . . . . . . . . . . . . . . 7-11
Drive Motor . . . . . . . . . . . . . . . 7-13
Motor Brushes . . . . . . . . . . . . 7-16
Elevation Motor. . . . . . . . . . . . 7-19
Lower Control Board . . . . . . . 7-21
Power Cord. . . . . . . . . . . . . . . 7-24
Power Switch . . . . . . . . . . . . . 7-24
Line Filter . . . . . . . . . . . . . . . . 7-25
Upper Display Board . . . . . . . 7-27
Contact Heart Rate Board . . . 7-29
CSAFE Board . . . . . . . . . . . . . 7-30
Display Cable . . . . . . . . . . . . . 7-31
Display Overlays . . . . . . . . . . . 7-34
Parts List . . . . . . . . . . . . . . . . 7-36
Exploded View . . . . . . . . . . . . 7-39
Schematic. . . . . . . . . . . . . . . . 7-40
Page 7-27