Firstech CM7000 Master Manual page 43

CM7000 Master Guide
FO2 - With Arm: this option will trigger AUX 1 (output time based on feature 4-01) any time the
CM7 is locked/armed the first time (i.e. if you send a second lock/arm command it will not trigger
again)
FO3 - With Disarm: this option will trigger AUX 1 (output time based on feature 4-01) any time
the CM7 is unlocked/disarmed. Note: the system has to be in the armed state when
disarming in order to trigger AUX 1. (I.e. if the vehicle is already in the unlocked/
disarmed state and you send a second unlock/disarm command it will not trigger the
output)
FO4 - With ignition removed: this option will trigger AUX 1 (output time based on feature
4-01) as soon as Ignition input is removed from the CM7. (I.e. this feature can be used with a
manual transmission vehicle to open the door input circuit on the CM7 for a set period of time when
reservation mode is complete in order to prevent the dome light from cancelling reservation mode.)
4-04 Aux 2 Output Control: This feature allows the user to configure the method of which Auxiliary 2 can
be activated.
FO1 - Remote: (default) this option allows AUX 2 (output time based on feature 4-02) to be
triggered by any 4 button Firstech remote or drone.
FO2 - With Arm: this option will trigger AUX 2 (output time based on feature 4-02) any time the
CM7 is locked/armed the first time (I.e. if you send a second lock/arm command it will not trigger
again)
FO3 - With Disarm: this option will trigger AUX 2 (output time based on feature 4-02) any time the
CM7 is unlocked/disarmed. Note: the system has to be in the armed state when disarming in order
to trigger AUX 1. (I.e. if the vehicle is already in the unlocked/disarmed state and you send a second
unlock/disarm command it will not trigger the output)
FO4 - With Start: This option will trigger the AUX 2 (output time based on feature 4-02) when the
remote start sequence is initiated. It will trigger at the same time as GWR (ground when running)
4-05 Secure Aux Output: this feature is designed to prevent accidental activation of the AUX outputs by
requiring an additional step when using any 4 button or 2 way LCD Firstech remote.
FO1- On: (default) this option will require the user to perform an additional step before activating
AUX output using any Firstech 4 button or 2 way LCD remote (2way remotes with Roman numeral
buttons will require a 0.5 second tap of button IV before activating any of the AUX outputs.2Way LCD
remotes with lock/unlock/trunk/start icons on the buttons use the start button for the same. 1way
remotes require the user to hold trunk + start buttons for 2.5 seconds before activating AUX outputs.)
FO2- Off: this option will disable the additional step required by the user to activate the AUX outputs.
*NEW* FO3- On while armed: this feature will only require the user to perform the additional
override step to activate Aux outputs ONLY WHEN the CM7 is ARMED. While the system is
disarmed or unlocked this step is not required.
4-06 AUX input 1 (-): (green AUX sensor connector input pin 4) this feature will determine the operation
of the AUX input 1 on the green input connector.
FO1- Pre-Warn: This option will allow AUX sensor input 1 to activate the pre-warn cycle on the
CM7 when triggered with negative input. (I.e. additional proximity or impact sensor pre-warn trigger)
Copyright 2014 Firstech, LLC.
Alarm and Starter System
techfeed.compustar.com
Page 43