Integra DTR-50.1 Instruction Manual page 12

Front & Rear Panels—Continued
COMPONENT VIDEO IN 1, 2 and 3
These RCA component video inputs are for con-
necting components with a component video out-
put, such as a DVD player, DVD recorder, or DVR
(digital video recorder). They're assignable, which
means you can assign each one to an input selector
to suit your setup. See "Component Video Input
Setup" on page 48.
COMPONENT VIDEO MONITOR OUT
These RCA component video outputs are for con-
necting a TV or projector with a component video
input.
COMPONENT VIDEO ZONE 2 OUT
This RCA component video output is for connect-
ing a TV or projector with a component video input
located in your main listening room or Zone 2.
FM ANTENNA
This jack is for connecting an FM antenna.
AM ANTENNA
These push terminals are for connecting an AM
antenna.
IR IN/OUT
A commercially available IR receiver can be con-
nected to the IR IN jack, allowing you to control the
AV receiver while you're in Zone 2/3, or control it
when it's out of sight, for example, installed in a
cabinet.
A commercially available IR emitter can be con-
nected to the IR OUT jack to pass IR (infrared)
remote control signals through to other components.
12V TRIGGER OUT (A/B/C)
These outputs can be connected to the 12-volt trig-
ger inputs on other components.
AC INLET
The supplied power cord is connected here. The
other end of the power cord should be connected to
a suitable wall outlet.
GND screw
This screw is for connecting a turntable's ground
wire.
PHONO IN
These analog audio inputs are for connecting a turn-
table.
CD IN
These analog audio inputs are for connecting a CD
player's analog audio output.
TV/TAPE IN/OUT
These analog audio inputs and outputs are for con-
necting a TV or recorder with an analog audio input
and output (cassette, Mini Disc, etc.).
GAME IN
Here you can connect a game console, etc. Input
jacks include S-Video, composite video, and analog
audio.
12
CBL/SAT IN
Here you can connect a cable/satellite receiver, set-
top box, etc. Input jacks include S-Video, composite
video, and analog audio.
VCR/DVR IN/OUT
Here you can connect a VCR or DVR (digital video
recorder). Input and output jacks include S-Video,
composite video, and analog audio.
DVD/BD IN
Here you can connect a DVD/BD player. Input
jacks include S-Video, composite video, and analog
audio. You can connect a DVD/BD player's 2-chan-
nel analog audio output.
PRE OUT: FRONT L/R, CENTER, SURR L/R,
and SURR BACK L/R
These multichannel analog audio outputs can be
connected to the analog audio input on a multichan-
nel power amplifier for when you want to use the
AV receiver solely as a preamplifier.
PRE OUT: SUBWOOFER
This analog audio output can be connected to a
powered subwoofer. You can connect the powered
subwoofer with two PREOUT: SUBWOOFER
jacks respectively. The same signal is output from
each jack.
PRE OUT: ZONE 2, ZONE 3 L/R
These analog audio outputs can be connected to the
line inputs on amplifiers in Zone 2 and Zone 3.
FRONT L/R, CENTER, SURR/ZONE 3 L/R,
SURR BACK/ZONE 2 L/R, FRONT HIGH L/R,
and FRONT WIDE L/R
These terminal posts are for connecting the front
L/R, center, surround/zone 3 L/R, surround back/
zone 2 L/R, front high L/R, and front wide L/R
speakers.
The FRONT L/R and SURR BACK/ZONE 2 L/R
terminal posts can be used with front speakers and
surround back speakers respectively, or used to bi-
amp the front speakers. See "Bi-amping the Front
Speakers" on page 20".
The SURR BACK/ZONE 2 L/R terminals can be
used with surround back speakers respectively, or
used to connect the speakers in Zone 2.
See "Connecting Zone 2" on page 130.
The SURR/ZONE 3 L/R terminals can be used with
surround speakers respectively, or used to connect
the speakers in Zone 3.
See "Connecting Zone 3" on page 132.
See pages 17 to 40 for connection information.