Fluke 9100 User Handbook Manual page 238

Final Width = 215mm
10.4.6.4 Calibration Setup
1. Connections Ensure that the Model 9100 is connected to the Standards DMM as shown in Fig. 10.4.6.1 or 10.4.6.2
(depending on the current being calibrated), and that both instruments are powered on and warmed up. If the
measuring instrument has a switchable signal guarding facility it should be switched to remote guard. If it
does not have a guard facility, there can be no guard lead to the DMM.
2. 9100 a. Ensure that the 9100 is in STANDARD CAL mode and then select the AC Current function by pressing
the 'A' key on the right of the front panel, followed by pressing the ' A' screen key adjacent to the display.
b. Ensure that Sinusoidal waveshape is selected, and that the Phase facility is deselected (
lettering on light background).
Table 10.4.6.1: AC Current (Zero to 320mA) Hardware Configurations and Calibration Points
Output span Output
covered by to select
hardware hardware
configuration config. Default
000.000 A 100 A 300.000 A
to 300.000 A
320.000 A 300.000 A
0.32001mA 1mA 3.00000mA
to 3.00000mA
3.20000mA 3.00000mA
3.2001mA 10mA 30.0000mA
to 30.0000mA
32.0000mA 30.0000mA
32.001mA 100mA 300.000mA
to 300.000mA
320.000mA 300.000mA
Table 10.4.6.2: AC Current (0.32A to 20A) Hardware Configurations and Calibration Points
Output span Output
covered by to select
hardware hardware
configuration config. Default
0.32001A 1A 3.00000A
to 3.00000A
3.20000A 3.00000A
3.2001A 10A 10.0000A
to 10.0000A
20.0000A 10.0000A
10.4-30 Section 10: Calibrating the Model 9100: AC Current Function
Calibration Targets
Amplitude
Minimum Maximum Default
180.000 A 320.000 A 110.00Hz
180.000 A 320.000 A 3.0000kHz
180.000 A 320.000 A 30.000kHz
1.80000mA 3.20000mA 110.00Hz
1.80000mA 3.20000mA 3.0000kHz
1.80000mA 3.20000mA 30.000kHz
18.0000mA 32.0000mA 110.00Hz
18.0000mA 32.0000mA 3.0000kHz
18.0000mA 32.0000mA 30.000kHz
180.000mA 320.000mA 110.00Hz
180.000mA 320.000mA 3.0000kHz
180.000mA 320.000mA 30.000kHz
Calibration Targets
Amplitude
Minimum Maximum Default
1.80000A 3.20000A 110.00Hz
1.80000A 3.20000A 3.0000kHz
1.80000A 3.20000A 10.000kHz
7.0000A 10.5000A 110.00Hz
7.0000A 10.5000A 3.0000kHz
7.0000A 10.5000A 10.000kHz
label dark
Factor
Number
Frequency
Minimum Maximum
10.00Hz 320.00Hz 1
1.0000kHz 5.000kHz 2
20.000kHz 30.000kHz 3
10.00Hz 320.00Hz 1
1.0000kHz 5.000kHz 2
20.000kHz 30.000kHz 3
10.00Hz 320.00Hz 1
1.0000kHz 5.000kHz 2
20.000kHz 30.000kHz 3
10.00Hz 320.00Hz 1
1.0000kHz 5.000kHz 2
20.000kHz 30.000kHz 3
Factor
Number
Frequency
Minimum Maximum
10.00Hz 320.00Hz 1
2.0000kHz 4.000kHz 2
7.000kHz 10.000kHz 3
10.00Hz 320.00Hz 1
2.0000kHz 4.000kHz 2
7.000kHz 10.000kHz 3