Roland V-Card VC-1 Owner's Manual page 142

MIDI Implementation
❍Portamento Time (Controller number 5)
Status 2nd byte
BnH 05H
n = MIDI channel number:
vv = Portamento Time:
❍Data Entry (Controller number 6, 38)
Status 2nd byte
BnH 06H
BnH 26H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
❍Volume (Controller number 7)
Status 2nd byte
BnH 07H
n = MIDI channel number:0H - FH (ch.1 - 16)
vv = Volume: 00H - 7FH (0 - 127)
❍Hold 1 (Controller number 64)
Status 2nd byte
BnH 40H
n = MIDI channel number:
vv = Control value:
❍Portamento Switch (Controller number 65)
Status 2nd byte
BnH 41H
n = MIDI channel number:
vv = Control value:
❍RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are
extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in
any order) should be sent in order to select the parameter, then Data Entry
(Controller numbers 6 and 38) should be sent to set the value.
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB
00H, 00H mmH, llH
00H, 01H mmH, llH
142
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
llH
3rd byte
vvH
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
0 - 63 = OFF, 64 - 127 = ON
3rd byte
mmH
llH
Notes
Pitch Bender Range
mm: 00H - 0CH (0 - 12 semitones)
ll: ignored (processed as 00H)
Up to 1 octave can be specified in semitone
steps.
Fine Tuning
●Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number:
pp = Program number:
* Not received when the Program Change Switch (SYSTEM MIDI) is OFF.
●Channel Aftertouch
Status 2nd byte
DnH vvH
n = MIDI channel number:
vv = Aftertouch Value:
●Pitch Bender Change
Status 2nd byte
EnH llH
n = MIDI channel number:
mm, ll = Pitch Bender value:
■Channel Mode Messages
●All Sounds Off (Controller number 120)
Status 2nd byte
BnH 78H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, all notes currently sounding on the
corresponding channel will be turned off.
●Reset All Controllers (Controller number 121)
Status 2nd byte
BnH 79H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, all controllers on the corresponding channel will
be set to their reset values.
■MONO (Controller number 126)
Status 2nd byte
BnH 7EH
n = MIDI channel number:
mm = mono number:
MONO mode, each message is recognized on the channel shown below.
Message Control in MIDI function
B.CH
Note on/off
Control Change basic
Mode Message basic
Program Change basic
Aftertouch basic
Pitch Bender Change
Exclusive basic
mm, ll: 00 00H - 40 00H - 7F 7FH
( -50 - 0 - +50 cent)
0H - FH (ch.1 - 16)
00H - 3FH (prog.1 - prog.64)
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
0H - FH (ch.1 - 16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
3rd byte
00H
3rd byte
00H
3rd byte
mmH
0H - FH (ch.1 - 16)
00H - 10H (0 - 16)
G.CH
individual
Global
Global
Global
Global
individual
Global