Roland VS8F-3 Owner's Manual
  1. Manuals
  2. Brands
  3. Roland Manuals
  4. Computer Hardware
  5. VS8F-3
  6. Owner's manual

Roland VS8F-3 Owner's Manual

Roland vs8f-3 expansion board: owners manual
Hide thumbs Also See for VS8F-3:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Workshop Manual
Owner's Manual
201a
Before using this unit, carefully read the sections entitled: "USING THE UNIT
SAFELY" and "IMPORTANT NOTES" (Owner's Manual p. 2, p. 3).
These sections provide important information concerning the proper operation
of the unit. Additionally, in order to feel assured that you have gained a good
grasp of every feature provided by your new unit, the owner's manual should
be read in its entirety. The owner's manual should be saved and kept on hand
as a convenient reference.
202
Copyright © 2004 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
Roland Web site http://www.roland.com/

Advertisement

Table of Contents
loading

Related Manuals for Roland VS8F-3

Summary of Contents for Roland VS8F-3

  • Page 1 The owner’s manual should be saved and kept on hand as a convenient reference. Copyright © 2004 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Roland Web site http://www.roland.com/...
  • Page 2 022c • Before installing the VS8F-3, you must first always turn off the VS series device and unplug its power cord.

  • Page 3: Important Notes

    IMPORTANT NOTES Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. Additional Precautions •...

  • Page 4: Table Of Contents

    Rules for installing effect expansion boards ... 9 What is the Key Card? ... 9 Rule 1 ... 9 Rule 2 ... 9 Where to install the VS8F-3 (Checking the first slot) ... 10 VS-2480/2480CD ... 10 VS-2400CD... 10 VS-2000... 10 Installing plug-in effects in the V Studio ...11...

  • Page 5: Introduction

    Introduction Features of the VS8F-3 The VS8F-3 is an optional board that can be installed in an effect expansion slot of a supported VS series unit to add or expand its effect-processing capabilities. • Switching between various effect programs written specifically for the VS8F-3 allows the VS8F-3 to produce different effects.

  • Page 6: Before You Use The Vs8F-3

    Before you use the VS8F-3 To use VS8F-3 in a VS series recorder, the system program version of the V Studio must be compatible with the VS8F-3. Please check the system program version of your VS series recorder before installing the VS8F-3. If you find the version is not compatible with the VS8F-3, please update the software using the SETUP DISC contained in this package.

  • Page 7: Using The Setup Disc To Update The System Version

    Here's how to update the system program of your VS series device so that it will support the VS8F-3. You'll need to perform this step just once for VS series devices whose system does not yet support the VS8F-3. To update the system program of your VS series device, use the “SETUP DISC”...

  • Page 8: Recovering Your Projects

    (Data compatibility is preserved.) Installing the VS8F-3 Installation of the VS8F-3 is exactly the same as installing the VS8F-2. Refer to the Quick Start manual for your VS series device and to Rules for installing effect expansion boards (p.

  • Page 9: Rules For Installing Effect Expansion Boards

    When installing the VS8F-3, you must install it as follows in conformity with Rule 1. When the VS8F-3 in the first slot (the Key Card, shown here in bold type) is authorized, Key Card data is written to the hard disk together with the VS plug-in program.

  • Page 10: Where To Install The Vs8F-3 (Checking The First Slot)

    Before you use the VS8F-3 Where to install the VS8F-3 (Checking the first slot) ■ VS-2480/2480CD AC Cord Unplug the power before installing an effect expansion board. Effect expansion board installation opening VS-2480/2480CD bottom ■ VS-2400CD AC Cord Unplug the power before installing an effect expansion board.

  • Page 11: Installing Plug-In Effects In The V Studio

    Reload the current project • Press [F4 (UnSel)] in PLUG-IN SELECT screen In both of the above cases, the VS8F-3 will be set to NO PLUG-IN status (no plug in program is loaded). p. 10 and the VS plug-in program is stored to...

  • Page 12: Installation Examples

    VS8F-3 installed, the VS plug-in programs installed on the hard disk cannot be used as authorized plug-ins. If you own one VS series unit and two (or more) VS8F-3 boards When authorizing, a VS8F-3 must be installed in the first slot (p. 10).
  • Page 13 VS series units at the same time. Key Card is not found VS series (#1) Please place the Key Card sticker on the VS8F-3 that is designated as the Key Card (To learn about the Key Card, please refer p. 9). before the authorization VS series...
  • Page 14 (#1) If you leave the Key Card in the first VS series unit and install the other (i.e., non-Key Card) VS8F-3 boards in the second VS series unit, the VS plug-in programs installed in the second VS series unit will not be usable. Nor can you use an already-authorized SETUP DISC to install an authorized version of the same VS plug-in programs to any VS without the original Key Card installed.

  • Page 15: Installation Procedure

    Installation procedure 1. Carefully read the included leaflet “License agreement for Roland software” and verify that you accept the conditions. 2. Insert the SETUP DISC into the CD-R/RW drive. 3. Press [CD-RW]. The CD-RW menu screen will appear. 4. Select Page 2 “PLUG-IN Inst,” and press [ENTER/YES].

  • Page 16: Re-Installing Your Plug-Ins

    If you initialize (format) the hard disk of your VS series unit, the VS plug-in programs on the hard disk will be lost, leaving you unable to use the VS plug-in programs even if the VS8F-3 is installed. By re-installing the VS plug-in programs you will again be able to use them.

  • Page 17: Using The Effects

    Now that you've installed the VS8F-3 in your VS series unit, let's try out the effects. A VS8F-3 effect can be used as an insert effect or loop effect in the same way as an effect on the VS8F-2. For details, refer to the owner's manual of your VS series unit.

  • Page 18: Editing The Effect Parameters

    Using the effects ■ Editing the effect parameters Here's how to edit the effect parameters of the selected patch. 1. Select a patch as described in Selecting a plug-in’s patch (p. 17). 2. Press [F4 (Edit)]. The PLUG-IN screen will appear. The controllers operate as follows. Controller How to use (Top panel) Move the cursor to the value, and edit it using...

  • Page 19: Effect Algorithm

    ■ About the included Roland VS plug-ins Each VS8F-3 includes five Roland plug-ins that can be installed from a SETUP DISC included in the box. The VS8F-3 recalls the following VS plug-in programs from the hard disk and changes its effect algorithm accordingly.

  • Page 20: Mastering Tool Kit

    Effect Algorithm Mastering Tool Kit This is a compressor that divides the input signal into frequency bands (High, Middle, and Low) and regulates the volume of each band. When mixing down to MD or DAT, or when using a CD-R disc to produce an original audio CD, you can apply this effect to master your song at the optimal level.
  • Page 21 ENHANCER Accentuates the sound and pushes the sound forward. Parameter (full name) Setting Sw (Switch) OFF, ON FREQ (Frequency) 200~20000 Hz SENS (Sensitivity) 0~100 MIX LEVEL 0~12.0 dB INPUT Splits the direct sound into three frequency bands, that is, Low, Middle and High frequency bands. Parameter (full name) Setting IN GAIN (Input Gain)
  • Page 22 Effect Algorithm COMP (Compressor) Compresses the entire output signals when the input volume exceeds a specified value. Parameter (full name) Sw (Switch) HIGH THRE (High Threshold) HIGH RATIO HIGH ATK (High Attack) HIGH REL (High Release) MID THRE (Middle Threshold) MID RATIO (Middle Ratio) MID ATK (Middle Attack) MID REL (Middle Release)

  • Page 23: Tempo Mapping Effect

    Tempo Mapping Effect This is a stereo delay that lets you specify the delay time relative to the tempo. Since you can set the delay time as a note value length, you don't have to perform annoying manual calculations to determine the time based on the tempo. Because this can be synchronized to the MIDI clock from the VS series unit, it will automatically follow any tempo changes during the song.
  • Page 24 Effect Algorithm L-ch DELAY Parameter (full name) INI.DLY (Initial delay time) INI.D.PAN (Initial delay pan) D.TIME (Delay time) MOD DEPTH (Modulation depth) FB (Feedback level) X-FB (Cross feedback level) LF DAMP GAIN LF DAMP FREQ HF DAMP GAIN HF DAMP FREQ R-ch DELAY Parameter (full name) INI.DLY (Initial delay time)
  • Page 25 (*4) The note value lengths have the following significance. Display Explanation no delay sound. a whole note 1/1t a whole note triplets a half note 1/2t half note triplets a quarter note 1/4t quarter note triplets an eighth note 1/8t eighth note triplets 1/16 a sixteenth note...

  • Page 26: Stereo Reverb

    Effect Algorithm Stereo Reverb This models the reflections and reverberation of a hall or room, as well as its spatial character. Since both input and output are stereo, you can add reverberation without impairing the stereo image created by panning the input source. Input L Compressor Expander...
  • Page 27 EXP (Expander) If the input volume drops below the specified threshold, this will expand the dynamic range of the output signal. Parameter (full name) Setting Sw (Switch) OFF, ON THRE (Threshold) -80.0~0.0 dB RATIO 1:1.00~1:16.0, 1:∞ ATK (Attack) 0.0~800.0 ms REL (Release) 50~8000 ms REVERB...

  • Page 28: Vocal Channel Strip

    Effect Algorithm Vocal Channel Strip This is a multi-effect suitable for use when recording or processing a vocal. This one algorithm can be used on up to two monaural channels simultaneously with independent controls. Input L Compressor Expander Compressor Expander Input R TARGET (Edit target) Parameter (full name)

  • Page 29: Pre-Amp Modeling

    (*4) Company names and product names appearing in patch names and other places are the trademarks or registered trademarks of their respective owners, and have no connection with Roland Corporation. These names are used in order to convey the character of the sound being simulated by the preamp model.

  • Page 30: Preset Patch List

    Preset Patch List Mastering Tool Kit Number Name P000 Mixdown P001 PreMastering P002 Live Mixing P003 Pop Mixing P004 Dance Mixing P005 Jingle Mixing P006 Hard Comp P007 Soft Comp P008 Clean Comp P009 Dance Comp P010 Orchestra Comp P011 Vocal Comp P012 Acoustic Guitar...
  • Page 31 Number Name P057 Long Cave P058 Garage Drums P059 Rock Kick P060 Rock Snare Vocal Channel Strip Number Name P061 VO:Vocal Fx P062 VO:Jazz Vocal P063 VO:Rock Vocal P064 VO:Big Chorus P065 VO:Male Vocal P066 VO:Rock Male Vocal P067 VO:Jazz Male Vocal P068 VO:Female Vocal P069...

  • Page 32: Troubleshooting

    Troubleshooting If the VS8F-3 does not operate correctly even when you've installed it as directed by the owner's manual, or does not operate as you expect, please check the following points. ■ Installation Can't install • The VS8F-3 is not inserted.

  • Page 33: Precautions When Requesting Service For The Vs8F-3

    If for some reason the VS8F-3 fails to operate properly, and repair or replacement is necessary, there are some cases in which you will also need to send us the other VS8F-3 unit(s) that you were using at that time, and/or the SETUP DISC.
  • Page 34 Memo...
  • Page 35 Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. PHILIPPINES AFRICA AFRICA G.A. Yupangco & Co. Inc. 339 Gil J. Puyat Avenue EGYPT Makati, Metro Manila 1200,...

  • Page 36: Federal Communications Commission

    This product complies with the requirements of European Directive 89/336/EEC. FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

Table of Contents