Mute Button - ProScan PS20112 Owner's Manual

_R e mote _Co ntro I_F"_ ii_t i:_ s_
@ 0FF/ON BUTTONturns off the TV.
NUMBER BUTTONS let you select
directly
channels instead
of using the CHANNEL buttons. Always press two number
buttons (first one, then the other) to select a channel. For
example, press 0 then 6 for channel 6.
To select a 3-digit cable channel (like 127), press and
hold number button 1 until "1 - -" appears on the screen.
Then press the other two numbers. Your TV will tune up
to cable channel number 128 when the CABLE/AIR function
is set to CABLE. C heck with your cable company to
determine which channels are available in your area.
COMMERCIAL SKIPBUTTON
Use this button when you want to scan other channels
during a commercial break. When a program break
occurs, press cs once before changing channels. The TV
will count down 30 seconds on the screen and then
automatically switch back to the original channel you
were watching.
Press cs twice if you want the TV to count down 60
seconds. Each additional press will add another 30
seconds to the count-down time (up to five minutes) and
then each additional press will add another 60 seconds to
the countdown time (up to 60 minutes).
To cancel, press CLEAR. T he countdown clock will
disappear from the screen, and the TV will stay tuned to
the channel it was on when you pressed CLEAR.
INPUT BUTTONlets you quickly
view signals from the
INPUTjacks. Pressing this button switches the TV from
its current channel directly to channel 90, then channel
91, then channel 92. Channel 90 lets you see the signals
coming from a device that is connected to the s-vloEo
connector. Channel 91 accesses the INPUT1 jacks and
channel 92 accesses the INPUT2 jacks.
@+
AND - BU'I]'ONS
Use these buttons
after you have pressed the MENUbutton
to enter or adjust functions.
@ MENtl BUTTON
Press MENUrepeatedly
until the menu you want to display
is selected, then press + or-. Next press MENU
repeatedly to select the function you want to adjust and
then press + or - to adjust the setting. Details about
using each function begin on page 8.
ANTENNA BU'R'0N
Because your TV has two different antenna inputs on the
back (labeled ANTA and ANTB) yOU can connect more
than one antenna or signal source. Press the ANTENNA
button to switch from one input to the other.
The color of the channel number on the screen indicates
which antenna input you are watching. The channel
numbers are blue for ANTA and yellow for ANTB. If the
channel numbers are blue, you are watching whatever is
connected to the ANTAinput on the back of the TV. If
®
®
@
@
@
@
®
the channel numbers are yellow, you are watching
whatever is connected to Ihe ANTB input on the back of
the "IV. Details are on page 21.
TVBUli'ONturns on TV and puts remote in "TV Mode"
so that the other remote battons will control the TV.
Also displays time (if clock has been set) and channel
number on the TV screen.
Important Note: Most butto as on the remote control will not
control the TV unless the rem3te is in the "TV Mode". If another
component button (such as vc R1, VCR2, or AUDIO) is pressed, the
remote will no longer be in th: "TV Mode." To get back into the
"TV Mode," simply press the button labeled Iv. The remote will
go back into the "TV Mode" and will control the TV again.
CHANNELBU'FrONS
Press CHANNEL up to see taP next higher channel in
memory, or press CHANNE Ldown to see the next lower
channel in memory. Channels 2 through 13 and 91 were
programmed into the channel memory for you at the
factory.
Your TV will automatically program active channels for
your area into memory v,hen you start the AutoProgram
feature described on page 18. If desired, you can also
add or erase individual channels as described on
page 19.
VOLUME BUTTONS
Press VOLUME
up to increase volume, or press
VOLUME
down to decrease volume. The volume display will
automatically appear on the screen when you press the
VOLUME b uttons.
PREVIOUSCHANNELBUTTON
Pressing the PC button causes the TV to change back to
the last-tuned channel. This is useful should you want to
monitor two channels.
To operate, select the first channel you want to watch.
Then select the other channel by pressing two number
buttons. The TV will now change back and forth
between the two channets each time you press the
PC button.
MUTEBUTTON
Press
MUTE
to quickly reduce sound to its minimum
level without affecting ttzepicture. This is very useful
during telephone calls or other interruptions. When
sound is muted, the word MUTE will appear on the
screen. To restore sound, press
MOTE
again, or press
VOLUME
up.
CLEAR BUTTON
Pressing CLEAR quickly clears the screen of all on-screen
display messages (except mute and parental control). It
is also used to cancel th: Commercial Skip count-down
clock and to erase channel labels.
DISPLAY BUTTON displays time (if clock has been set)
and channel number on the TV screen. Also quickly
removes menus and displays from the screen.
O
,O
Into
__37