Configuring Ssid Profiles; Figure 148 Menu 3.5.5 - Layer-2 Isolation; Table 76 Menu 3.5.5 - Layer-2 Isolation - ZyXEL Communications G-3000 User Manual

Chapter 19 LAN Setup
3 Press [SPACE BAR] to select Access Point, AP + Bridge or MESSID in the
Operating Mode field and press [ENTER].
4 In the Edit Layer-2 Isolation field, press [SPACE BAR] to select Yes and press
[ENTER]. Menu 3.5.5 - Layer-2 Isolation displays as shown next.

Figure 148 Menu 3.5.5 - Layer-2 Isolation

--------------------------------------------------------------------------
1=
2=
3=
4=
5=
6=
7=
8=
9=
10=
11=
12=
--------------------------------------------------------------------------
The following table describes the fields in this menu.

Table 76 Menu 3.5.5 - Layer-2 Isolation

FIELD
Allow devices with
these MAC
addresses
1..32
When you have completed this menu, press [ENTER] at the prompt "Press ENTER to confirm or ESC
to cancel" to save your configuration or press [ESC] to cancel and go back to the previous screen.

19.3.5 Configuring SSID Profiles

When the ZyXEL Device is set to MESSID mode, you need to choose the SSID profile(s) you
want to use in your wireless network (see
operating modes).
Follow the steps below to set which SSID profiles your ZyXEL Device uses.
1 From the main menu, enter 3 to open Menu 3 – LAN Setup.
218
Menu 3.5.5 - Layer-2 Isolation
Allow devices with these MAC addresses
----
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
00:00:00:00:00:00
----
Press ENTER to Confirm or ESC to Cancel:
DESCRIPTION
These are the MAC address of a wireless client, AP, computer or router. A
wireless client associated with the ZyXEL Device can communicate with
another wireless client, AP, computer or router only if the MAC addresses of
those devices are listed in this table.
Enter the MAC addresses (in XX:XX:XX:XX:XX:XX format) of the client
computers that are allowed or denied access to the ZyXEL Device in these
address fields.
13= 00:00:00:00:00:00
14= 00:00:00:00:00:00
15= 00:00:00:00:00:00
16= 00:00:00:00:00:00
17= 00:00:00:00:00:00
18= 00:00:00:00:00:00
19= 00:00:00:00:00:00
20= 00:00:00:00:00:00
21= 00:00:00:00:00:00
22= 00:00:00:00:00:00
23= 00:00:00:00:00:00
24= 00:00:00:00:00:00
Section 6.6 on page 78
25= 00:00:00:00:00:00
26= 00:00:00:00:00:00
27= 00:00:00:00:00:00
28= 00:00:00:00:00:00
29= 00:00:00:00:00:00
30= 00:00:00:00:00:00
31= 00:00:00:00:00:00
32= 00:00:00:00:00:00
for more information on
G-3000 Series User's Guide