Table of Contents
Advertisement
Camera menu items (continued)
FALL S-CURVE [0 to 30]
Sets the S-curve for pan/tilt deceleration operation in 31 steps. (The
greater the number, the steeper the S-curve)
When it is necessary to reduce the speed to the specified speed
using manual control of pan/tilt by lever operation etc. through the
controller, the deceleration process is performed based on the
S-curve specified in this setting.
This is enabled only when [P/T ACCELERATION] is [MANUAL].
<NOTE>
• In order to limit the deceleration response, in the S-curve step, as
the deceleration speed rises, the limit is automatically applied.
• For the relationships between the various setting values in
[P/T ACCELERATION SETTING], refer to the diagram on page
76.
RISE ACCELERATION [1 to 255]
Sets the acceleration speed for pan/tilt acceleration operation
in 255 steps. (The acceleration speed increases as the number
increases)
When it is necessary to increase the speed to the specified speed
using manual control of pan/tilt by lever operation etc. through the
controller, the acceleration process is performed based on the
acceleration speed specified in this setting.
This is enabled only when [P/T ACCELERATION] is [MANUAL].
<NOTE>
• When the specified acceleration speed is small, it is not possible
to reach the maximum speed of the product.
FALL ACCELERATION [1 to 255]
Sets the deceleration speed for pan/tilt deceleration operation
in 255 steps. (The deceleration speed increases as the number
increases)
When it is necessary to reduce the speed to the specified speed
using manual control of pan/tilt by lever operation etc. through the
controller, the deceleration process is performed based on the
deceleration speed specified in this setting.
This is enabled only when [P/T ACCELERATION] is [MANUAL].
<NOTE>
• The deceleration and stop processes are carried out right up to
the end of the lens mechanism section and in order to prevent
a collision with the mechanism, in the actual operation, [FALL
ACCELERATION] may be restricted.
SPEED WITH ZOOM POSITION [OFF, ON]
[OFF] or [ON] is set here for the function used to adjust the pan/tilt
adjustment speed in conjunction with the zoom magnification.
When [ON] is set, the panning and tilting operations will become
slower in the zoom status.
This function has no effect during preset operations.
FOCUS ADJUST WITH PTZ. [OFF, ON]
[OFF] or [ON] is set here for the function which compensates for
out-of-focusing when it occurs during panning, tilting or zooming
operations.
When [OFF] is set, adjust the focus as required after zooming or set
[FOCUS MODE] to [AUTO].
This is only enabled when [MANUAL] has been selected as the
[FOCUS MODE] setting.
PRIVACY MODE [OFF, ON]
Sets OFF/ON the function for turning the camera direction down when
this unit is changed to STANDBY mode.
OFF
Does not change the camera direction when the camera
is switched to STANDBY mode. (The camera direction
from the POWER ON state is maintained.)
ON
Moves the camera to face toward the rear when the
camera is switched to STANDBY mode.
When the unit switches again to the POWER ON state,
the unit moves to the position according to [POWER ON
POSITION].
POWER ON POSITION
[NONE, STANDBY, HOME, PRESET]
Select the initial positions for PAN/TILT/ZOOM when the power is
turned on.
NONE
Maintains the PAN/TILT position when the power is
turned on, and ZOOM will be at the Wide end.
STANDBY
Move to the PAN/TILT/ZOOM positions they were in the
last time the camera was switched to STANDBY mode.
HOME
PAN/TILT move to their home positions (front) and
ZOOM goes to the Wide end.
PRESET
Preset playback is performed at the preset position
specified with [PRESET NUMBER].
PRESET NUMBER [001 to 100]
Specify a number for preset playback when the power turns ON when
[PRESET] is set in [POWER ON POSITION].
<NOTE>
• If an unregistered preset number is set, preset playback is not
performed and the operation is the same as [STANDBY].
75
Advertisement
Table of Contents
