Panasonic HEVC Advance AW-UE160WP Operating Instructions Manual page 105

Web screen operations (continued)
1.
Menu switching [Stream Menu]/[Other Menu]
Switch between menu displays.
Clicking [Other Menu] when the Stream menu is displayed displays
the Other menu.
Clicking [Stream Menu] when the Other menu is displayed displays
the Stream menu.
2. Compression button [Compression]
The [H.264] button turns gray, and H.264 images
are displayed.
The [H.264] button is enabled when the [H.264
[H.264]
transmission] setting of [H.264(1)] to [H.264(3)] on
the Video over IP is [On]. (→ page 127)
The [JPEG] button turns gray, and JPEG images
are displayed.
[JPEG]
<NOTE>
• In the following cases, the selection status of the [Compression]
buttons will return to the setting configured in the [Video over IP] -
[Initial display setting] - [Stream] (→ page 126).
- When returning from another screen
- When the screen is updated
3.
Stream buttons [Stream]
When H.264 is selected
These buttons appear only when H.264 images are displayed.
When selected, the button turns gray, and the images
in the main area appear according to the settings
configured for [H.264(1)]. (→ page 127)
[1]
When selected, the button turns gray, and the images
in the main area appear according to the settings
configured for [H.264(2)]. (→ page 127)
[2]
When selected, the button turns gray, and the images
in the main area appear according to the settings
configured for [H.264(3)]. (→ page 127)
[3]
<NOTE>
• In the following cases, the selection status of the [Stream] buttons
will return to the setting configured in the [Video over IP] - [Initial
display setting] - [Stream] (→ page 126).
- When returning from another screen
- When the screen is updated
• If the H.264 image resolution is set to [1920x1080] or [1280x720],
the image may be compressed depending on the size of the web
browser window.
When JPEG is selected
These buttons appear only when JPEG images are displayed.
When selected, the button turns gray, and the images
in the main area appear according to the settings
configured for [JPEG(1)]. (→ page 126)
[1]
When selected, the button turns gray, and the images
in the main area appear according to the settings
configured for [JPEG(2)]. (→ page 126)
[2]
When selected, the button turns gray, and the images
in the main area appear according to the settings
configured for [JPEG(3)]. (→ page 126)
[3]
<NOTE>
• The resolution selected with [JPEG(1)], [JPEG(2)], and [JPEG(3)]
(→ page 126) under [JPEG] in the [Video over IP] will be used.
• If the resolution is set to [1920x1080] or [1280x720], the image may
be compressed depending on the size of the web browser window.
• In the following cases, the selection status of the [Image Capture
Size] buttons will return to the setting configured in the [Video over
IP] - [Initial display setting] - [Stream] (→ page 126).
- When returning from another screen
- When the screen is updated
4.
OSD Menu Operation [OSD Menu]
[ON] [OFF]
[Cancel]
[] [] [] [] [OK]
<NOTE>
• During IP video transmission (H.264/H.265/M-JPEG), there
may be some delays in OSD menu operations. Smooth OSD
menu operations become possible when you set [IP SIGNAL] –
[IP(H.264/H.265)] – [CHAR] to [OFF]. (→ page 58, page 124)
5. Color bar button [Color bar]
[ON] [OFF]
[Type1] [Type2] [Type3]
[Type4] [Type5]
105
Use this to select whether the camera's on-
screen displays are to be shown.
It cancels the selection of the setting which
is being changed. It restores the pre-change
setting.
Use these to perform the menu operations.
The items are selected using the
[] [] [] [] buttons.
If a selected item has a sub menu, this sub
menu is displayed by pressing the [OK]
button.
When the cursor is moved to any item on
the bottom-level setting screen and the [OK]
button is pressed, the setting of the selected
item starts flashing.
A setting for a regular menu item is reflected
immediately if it is changed while it is still
flashing. However, there are a number of
menu items whose setting is reflected only
after the [OK] button has been pressed,
causing the setting to stop flashing and the
new setting to be entered.
Switch the color bar signal displayed or hide.
Switch the color bar displayed between
Type1, Type2, Type3, Type4 and Type5.
This is only enabled when [Color bar] is set
to [ON].