Table of Contents
Advertisement
Camera menu items (continued)
IP(H.264/H.265) OUT1 [FULL, CROP]
IP(H.264/H.265) OUT2 [FULL, CROP]
Make the FULL/CROP settings for images output via H.264/H.265/
M-JPEG transmission (LAN connector).
The settings specified with [IP(H.264/H.265) OUT1] are applied to
transmitted images from each of the CH1 transmissions (H.264(1),
H.265(1), JPEG(1)).
The settings specified with [IP(H.264/H.265) OUT2] are applied to
transmitted images from each of the CH2 and CH3 transmissions
(H.264(2) and (3), H.265(2) and (3), JPEG(2) and (3)).
FULL
FHD down-converted images are output as is without
cropping UHD images.
CROP
Images with FHD cropped from UHD images are output.
The images output in this case are those with the crop
frame specified in [CROP OUT].
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
When the [Streaming mode] on the web screen is [NDI|HX V2],
[IP(H.264/H.265) OUT1] and [IP(H.264/H.265) OUT2] will have a
linked operation.
CROP MARKER [OFF, YL, G, MG, YL+G, YL+MG, G+MG,
YL+G+MG]
Make the settings for the crop frame displayed for images output
to the 3G SDI OUT1 connector, the 3G SDI OUT2/PM connector,
the MONITOR images of SMPTE ST2110, and the LAN connector
(H.264/H.265/M-JPEG).
OFF
Crop frame not displayed.
YL
Displays only the yellow crop frame.
G
Displays only the green crop frame.
MG
Displays only the magenta crop frame.
YL+G
Displays the yellow crop frame and the green crop frame.
YL+MG
Displays the yellow crop frame and the magenta crop
frame.
G+MG
Displays the green crop frame and the magenta crop
frame.
YL+G+MG
Displays the yellow crop frame, the green crop frame,
and the magenta crop frame.
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
<NOTE>
• Crop frames cannot be displayed via the 12G SDI OUT/SFP+
connector or HDMI connector, or with SMPTE ST2110 MAIN images
and SMPTE ST2110 CROP images.
CROP OUT [YL, G, MG]
Make the settings for the crop frame images output to the 3G SDI
OUT1 connector, cropped images of SMPTE ST2110, High
bandwidth NDI images, and the LAN connector (H.264/H.265/
M-JPEG).
YL
Outputs the yellow crop frame images.
G
Outputs the green crop frame images.
MG
Outputs the magenta crop frame images.
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
<NOTE>
• The color frame specified in [CROP OUT] will be a deeper shade
when compared to other colors used for frames.
• Cropped images cannot be output with the 12G SDI OUT/SFP+
connector, 3G SDI OUT2/PM connector, HDMI connector, SMPTE
ST2110 MAIN images, or SMPTE ST2110 MONITOR images.
CROP ADJUST [YL, G, MG]
Make selections for the crop frame to adjust positioning.
YL
Make adjustments to the position of the yellow crop
frame.
G
Make adjustments to the position of the green crop
frame.
MG
Make adjustments to the position of the magenta crop
frame.
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
<NOTE>
• The frame of the color specified in [CROP ADJUST] will be a thicker
frame compared to the frames of other colors.
CROP H POSITION [0 to 3072]
Make settings for the position in the horizontal direction for the crop
frame specified in [CROP ADJUST].
The variable range is 0 to 1920 when [UHD CROP] is [CROP(1080)]
and [CROP ZOOM] is [OFF], with 0 as the left edge and 1920 as the
right edge, and only even numbers can be set.
The variable range is 0 to 2560 when [UHD CROP] is [CROP(720)]
and [CROP ZOOM] is [OFF], with 0 as the left edge and 2560 as the
right edge, and only even numbers can be set.
The variable range when [CROP ZOOM] is [ON] is different
depending on the setting value of [CROP ZOOM RATIO], with the
variable range being 0 to 3072 when the [CROP ZOOM RATIO] is
500.00%, and only even numbers can be set.
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
CROP V POSITION [0 to 1728]
Make settings for the position in the vertical direction for the crop
frame specified in [CROP ADJUST].
The variable range is 0 to 1080 when [UHD CROP] is [CROP(1080)]
and [CROP ZOOM] is [OFF], with 0 as the upper edge and 1080 as
the lower edge.
The variable range is 0 to 1440 when [UHD CROP] is [CROP(720)]
and [CROP ZOOM] is [OFF], with 0 as the upper edge and 1440 as
the lower edge.
The variable range when [CROP ZOOM] is [ON] is different
depending on the setting value of [CROP ZOOM RATIO], with the
variable range being 0 to 1728 when the [CROP ZOOM RATIO] is
500.00%.
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
CROP ZOOM RATIO [120.00% to 500.00%]
Specifies the size of the CROP frame when [CROP ZOOM] is [ON].
The crop zoom ratio can be specified between the range of 120.00%
to 500.00%, and the grain-size can be set in units of 10.00% from the
OSD menu.
The variable range of the setting value of this item, the CROP frame
size, [CROP H POSITION] and [CROP V POSITION] is below.
CROP ZOOM
CROP frame size
RATIO
120.00%
3200×1800
200.00%
1920×1080
300.00%
1280×720
400.00%
960×540
500.00%
768×432
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
This is only enabled when [CROP ZOOM] is set to [ON].
73
Variable range
CROP H
CROP V
POSITION
POSITION
0 to 640
0 to 360
0 to 1920
0 to 1080
0 to 2560
0 to 1440
0 to 2880
0 to 1620
0 to 3072
0 to 1728
Advertisement
Table of Contents
