Panasonic HEVC Advance AW-UE160WP Operating Instructions Manual page 123

Web screen configurations (continued)
HDMI
Make the settings for output from the HDMI connector.
Format Select
Set the output format.
The following formats can be set depending on the settings in
[Format] in [Basic Config].
Frequency System Format
60Hz 2160/60p
1080/60p
59.94Hz 2160/59.94p
2160/29.97p
1080/119.88p
1080/59.94p
1080/29.97p
720/59.94p
50Hz 2160/50p
2160/25p
1080/100p
1080/50p
1080/25p
720/50p
24Hz 2160/24p
1080/24p
23.98Hz 2160/23.98p
1080/23.98p
When [UHD Crop] is [Crop(720)], output is 720/59.94p.
1
*
2 When [UHD Crop] is [Crop(720)], output is 720/50p.
*
Factory settings: 2160/59.94p or 2160/50p
HDR OUTPUT SELECT
[SDR(709), HDR(709), HDR(2020)]
Select the signal output when [HDR] is [On].
SDR(709) Selects the SDR output signal.
HDR(709) Selects the HDR output signal (BT.709 equivalent color
gamut).
HDR(2020) Selects the HDR output signal (BT.2020 equivalent color
gamut).
Factory settings: HDR(2020)
<NOTE>
• This cannot be set when the [Basic Config]
• [HDR(2020)] can be selected only when [Basic Config] – [GAMUT]
is [WIDE_G2].
V-LOG OUTPUT SELECT [V-LOG, V-709]
Format (HDMI)
2160/60p
1080/60p
Video Sampling [4:2:2/10bit, 4:2:0/8bit]
1080/60p
2160/59.94p
1
1080/59.94p
*
2160/29.97p
1080/29.97p
1080/119.88p
1080/59.94p
1080/59.94i
1080/29.97p
CHAR [Off, On]
720/59.94p
2160/50p
2
1080/50p
*
2160/25p
1080/25p
z Return
1080/100p
1080/50p
1080/50i
1080/25p
720/50p
2160/24p
1080/24p
1080/24p
2160/23.98p
1080/23.98p
RETURN1 ID
1080/23.98p
– [HDR] is [Off].
123
Select the signal output when [V-LOG] is [On].
V-LOG Output with a gamma curve that has a wide range of
tones and latitude (exposure range).
V-709 Converted for output to images suited to previewing.
Factory settings: V-LOG
<NOTE>
• This cannot be set when the [Basic Config] – [V-LOG] is [Off].
When [Format Select] in [HDMI] is [2160/59.94p], [2160/60p]
or [2160/50p], select the video sampling output from the HDMI
connector.
Factory settings: 4:2:2/10bit
<NOTE>
• When [Format Select] in [HDMI] is other than [2160/59.94p],
[2160/60p] or [2160/50p], [Video Sampling] cannot be changed and
is fixed at [4:2:2/10bit].
Set whether to superimpose the OSD.
Factory settings: On
You can give a name to the return images (SMPTE ST2110 input
images).
It can be 5 characters.
Alphanumeric characters, spaces, ! # % & ' ( )
_ ~ $ @ |
The setting is confirmed with the [Set] button.
The name you set is superimposed on the images output from
the same connector when [RETURN] is selected in [OUTPUT] –
[3G SDI OUT2/PM] – [OUTPUT SELECT].
<NOTE>
• This item cannot be set if the SMPTE ST2110 software key (AW-
SFU60) is disabled.
+ , - . / : ; < = > ? [ ]
*