Table of Contents
Advertisement
Web screen operations (continued)
22.
White balance [WB]
Switch the white balance in the order [AWB A], [AWB B],
[3200K], [5600K], [VAR], [ATW].
Switch the white balance in the order [AWB A], [ATW],
[VAR], [5600K], [3200K], [AWB B].
Automatic white balance (AWB) is executed and the white
balance is reset.
[AWB]
Automatic black balance (ABB) is executed and the black
balance is reset.
[ABB]
<NOTE>
• The current setting is displayed in the middle of the button.
23.
Shutter [Shutter]
Switch the shutter mode in the order [Off], [Step],
[Synchro], [Auto].
Switch the shutter mode in the order [Auto], [Synchro],
[Step], [Off].
<NOTE>
• The current setting is displayed in the middle of the button.
24.
ND filter [ND]
Switch the transmittance of the ND filter in the order
[Through], [1/4 ND], [1/16 ND], [1/64 ND].
Switch the transmittance of the ND filter in the order
[1/64 ND], [1/16 ND], [1/4 ND], [Through].
<NOTE>
• The current setting is displayed in the middle of the button.
• ND filter switching is not possible in night mode.
25.
SRT/MPEG2‑TS/RTMP
Starts streaming to the transmission destination
that was pre-registered.
(Streaming stopped)
The button turns red during transmission, and
transmission stops when the button is clicked
again.
(Streaming)
<NOTE>
• This button can be used only when [Streaming mode] is [RTMP],
[SRT(H.264)], [SRT(H.264 UHD)], [SRT(H.265)], [SRT(H.265
UHD)], or [MPEG2-TS over UDP].
• When [Streaming mode] is [SRT(H.264)], [SRT(H.264 UHD)],
[SRT(H.265)], or [SRT(H.265 UHD)], transmission can be started by
clicking this button only when the Client(Caller) mode is set.
26.
Button for switching the personal computer screen
Display the screen for mobile terminals.
For details, refer to "Displaying the web screen using a
mobile terminal" (→ page 192).
<NOTE>
• This button is displayed only when displaying on a mobile terminal.
27.
Preset thumbnail list display button
Display a list of Preset thumbnails on the live screen [Live].
28.
Button for switching real time updating
Frame dropping in images may be observed depending
on the operating performance of the personal computer
running the web browser. You can improve this problem
by pressing this button to disable the real time updating
function.
Data items subject to real time updating are as follows.
- Zoom
- Focus
- Iris
- Gain
- WB
- Shutter
- ND
<NOTE>
• The middle-click function is disabled if the button is enabled.
• The Audio Level Meter function is disabled if the button is enabled.
29.
Audio Level Meter display button
Display the status of audio input to this unit and the audio
setting status on the live screen [Live].
30.
Level Gauge switching button
When [ON], the status of the incline (horizontally, to the
left or right or front and back) of the unit installation is
displayed as OSD in the top left of the screen.
(Example)
L↑ +3.2/-3.2↓R
F↓ -1.8/+1.8↑F
In the case of the display above, the unit is installed at an
inclination of 3.2° upward to the left and 1.8° upward in to
the front.
The maximum incline is ±9.9°, and when there is an incline
of 10° or greater, the display shows "±9.9".
<NOTE>
• LEVEL GAUGE is displayed only through SDI, HDMI, and SMPTE
ST2110. It is not displayed with High bandwidth NDI and IP
transmission (H.264/H.265/M-JPEG).
109
Advertisement
Table of Contents
