Panasonic HEVC Advance AW-UE160WP Operating Instructions Manual page 50

Camera menu items (continued)
SYNC SIGNAL
Make settings to synchronize video/audio output signals.
REF SIGNAL [BBS/TRI‑LEVEL SYNC, PTP]
BBS/TRI-LEVEL Synchronization is according to the SDI reference
SYNC signal from the G/L connector.
PTP Synchronization is according to the PTP from the
SFP+ connector.
<NOTE>
• [PTP] cannot be selected if the SMPTE ST2110 software key
(AW-SFU60) is disabled.
• When [BASIC CONFIG] – [SFP+ MODE] is [12G OUTPUT], [PTP]
cannot be selected.
• When [IP SIGNAL] – [ST2110] – [MOIP MODE] is [OFF], [PTP]
cannot be selected.
GEN‑LOCK
Adjust the phase.
H PHASE-COURSE [–5 to 5]
Make coarse adjustments to horizontal phase in genlock.
H PHASE-FINE [–100 to 100]
Make fine adjustments to horizontal phase in genlock.
<NOTE>
• This cannot be set when the [BASIC CONFIG] – [SYNC SIGNAL]
– [REF SIGNAL] is [PTP].
BAR ID
BAR ID [OFF, ON]
Select OFF/ON for the ID display on the color bar.
BRIGHTNESS [0 to 100%]
Set the text color for the camera ID on the color bar.
ID1 POSITION V [0 to 5]
Specify the font units for the start position for display of the camera
ID1 (vertically: line number) on the color bar.
ID1 POSITION H [0 to 15]
Specify the font units for the start position for display of the camera
ID1 (horizontally: column number) on the color bar.
ID1
Set the character string for the [BAR ID].
Maximum 16 characters
(Alphanumeric characters, spaces, ! # % & ' ( )
_ ~ $ @ |)
ID2 POSITION V [0 to 5]
Specify the font units for the start position for display of the camera
ID2 (vertically: line number) on the color bar.
ID2 POSITION H [0 to 15]
Specify the font units for the start position for display of the camera
ID2 (horizontally: column number) on the color bar.
ID2
Set the character string for the [BAR ID].
Maximum 16 characters
(Alphanumeric characters, spaces, ! # % & ' ( )
_ ~ $ @ |)
OFFSET V [0 to 89]
Make fine adjustments to the display position of the [BAR ID] (offset
position of the pixels in the font: vertically).
OFFSET H [0 to 79]
Make fine adjustments to the display position of the [BAR ID] (offset
position of the pixels in the font: horizontally).
<NOTE>
• BAR ID is displayed only through the SDI, HDMI, SMPTE ST2110,
and High bandwidth NDI outputs. It is not displayed with IP
transmission (H.264/H.265/M-JPEG).
„
When the currently selected frequency is changed in [FREQUENCY],
the pre-frequency-change confirmation screen appears.
Pre‑frequency‑change confirmation screen
+ , - . / : ; < = > ? [ ]
*
+ , - . / : ; < = > ? [ ]
*
50
Changing the frequency
F R E Q U E N C Y
D o y o u w a n t t o s e t F r e q u e n c y ?
( 5 9 . 9 4 H z
C A N C E L
O . K .
• The frequency to be set is displayed within the parentheses on the
screen.
• When you move the cursor to [O.K.] on the pre-frequency-change
confirmation screen and confirm, the frequency is changed.
<NOTE>
• When using a monitor that does not support
60Hz/59.94Hz/50Hz/24Hz/23.98Hz frequencies, images may not
be displayed after the frequency is changed. Before changing the
frequency, verify that your monitor supports the frequency.
• When Frequency is changed, the unit restarts.
)