Table of Contents
Advertisement
SERVICE AND SETTING UP
-5,4)&5.#4)/. #/-054%2
KEY
A) Left multifunction digital display
(speedometer - odometer).
B) Multifunction computer programming push buttons.
C) Right multifunction digital display (coolant temperature
- clock - battery voltage - chronometer - diagnostic).
When the ignition key (1) is rotated to position "
following warning lights come on on the dashboard:
– red line warning light LED "max" (2);
– red engine oil pressure warning light LED "
which remains on until the engine starts.
The pointer (4) of the revolution counter shifts to the max-
imum value (rpm) set by the user.
After about three seconds the red line warning light LED
"max" (2) goes off; the pointer (4) of the revolution coun-
ter returns to its initial position.
(),
The writing "
" (5) appears on the right side of the
multifunction display for three seconds.
In this way the component operation is tested.
a
CAUTION
After the first 1000 km (625 mi) and successively eve-
ry 7500 km (4687 mi), the writing "SERVICE" (5a) ap-
pears on the right display.
In this case, carry out the operations prescribed in
the periodic service plan, see 2.1.1 (REGULAR SERV-
ICE INTERVALS CHART).
To make the writing "SERVICE" disappear, press the
"LAP" push button (6) and then the push button
and keep them pressed for about five seconds.
With the ignition key (1) in position
tings on the dashboard are the following:
Right display: Clock (7), coolant temperature in °C (8).
Left display: Instantaneous speed in km/h (9), trip 1 (trip
odometer) (10), total kilometres/miles odometer (11).
Upon installation of the battery or of the 30A main fuses:
– the revolution counter pointer (4) makes twelve clock-
wise clicks, thus checking the operation of the revolu-
tion counter itself;
– the instantaneous, maximum and average speed func-
tion is set in "km/h";
– the coolant temperature is set in °C;
– the digital clock is set to zero;
– the red line is set at 6000 rpm, indicated by the coming
on of the red line warning light LED "max " (red) (2).
NOTE
If necessary, carry out the appropriate adjust-
ments.
2.3.1 SEGMENT OPERATION CHECK
A
Press the push buttons
Rotate the ignition key (1) from position "
n
"
".
All the segments will remain on until the push buttons
B
and
are released.
2.3.2 SWITCHING FROM km TO mi (from km/h to
MPH) AND VICEVERSA (LEFT DISPLAY)
A
Press the push button
all the writings (12) on the left display start blinking.
Release the push button
B
Press the push button
urement from "km" to "mi" (from "km / h" to "MPH") or
viceversa.
2
- 6
n
", the
j
" (3),
n
the standard set-
"
"
B
and
at the same time.
m
" to position
until, after about five seconds,
A
.
to change the unit of meas-
V max
AVS
MPH
km/h
mi
km
A
9 10 11
8
A
7
6
5
rpm
x 1000
4
3
VEGLIA
BORLETTI
R
12
A
9
V max
10
9 10 11 12
8
A
max
7
6
DIAG
SERVICE
5
rpm
x 1000
4
1
3
2
N
VEGLIA
BORLETTI
B
2
1
12
max
1
2
N
3
4
AVS
MPH
km/h
mi
km
11
RSV mille
V BATT
C
6 6
Advertisement
Chapters
Table of Contents
Troubleshooting
