APRILIA RSV mille 956X Service And Repair Manual page 76

RSV mille
 &!34%.).' %,%-%.43
Check, and where necessary, tighten after the first 1000
km (625 mi) and then every 7500 km (4687 mi) or 8
months.
a
CAUTION
The fastening elements featured in the table must be
torqued to specification using a torque spanner and
®
LOCTITE applied, where indicated.
The elements marked (
for safety.
Description
Front connection
Left-side upper and lower rear connection
Adjusting bush right-side upper and lower rear connection
Lock ring right-side upper and lower rear connection
Screw right-side upper and lower rear connection
Description
Engine oil inlet flange
Engine oil drain plug
Rear brake lever mount fastening
Rear brake pump mount fastening
Pinion fastening
Clutch control cylinder fastening
Pinion case fastening
Fastening of fuel delivery pipe to throttle body
Coolant drain screw
Coolant thermistors
Description
Grooved ball bearings for selector roller / MS casing
Grooved ball bearings for selector roller / KS casing
Grooved ball bearings for propeller shaft / KS casing
Coolant pump idler gear / KS casing
MS casing / KS casing
MS casing / KS casing
MS casing / KS casing
MS casing / KS casing
Casing
Casing
Oil filter cover
Casing / injector 75
Bearing flange KS / MS
Bearing flange KS
Bearing flange MS
Bearing flange MS
) are particularly important
Fastening of engine to frame
Elements fastened to the engine
ENGINE
Q.ty Screw / nut
2+2
2
2 M20x1.5
2 M20x1.5
2
Q.ty Screw / nut
2
2
1
1
2
1
3
3
1 M12x1.5
1
2
Carter
Q.ty Screw / nut
Screw T.P.
1
M6 x 13
Screw T.P.
1
M6 x 13
Screw T.P.
2
M6 x 13
1 Pin 10
13 Screw T.C.E.I. M6 x 65
1 Screw T.C.E.I. M6 x 80
5 Screw T.C.E.I. M6 x 45
1 Screw T.C.E.I. M6 x 25
Magnetic screw
1
M12 x 1.5
1 Contact screw M10
2 Screw T.C.E.I. M6 x 20
1 Screw T.C.E.I. M6 x 10
2 Screw T.E. M8 x 45
2 Screw T.E. M8 x 25
1 Screw T.C.E.I. M8 x 20
1 Screw T.C.E.I. M6 x 20
SERVICE AND SETTING UP
Nm kgm
M10 40 4.0
M10 50 5.0
12 1.2
50 5.0
M10 50 5.0
Nm kgm
M6 12 1.2
M6 12 1.2
M6 10 1.0
M8 17 1.7
M8 17 1.7
M10 50 5.0
M6 12 1.2
M6 6 0.6
22 2.2
M6 10 1.0
M14 30 3.0
Nm kgm
11 1.1
11 1.1
11 1.1
– –
11 1.1
11 1.1
11 1.1
11 1.1
20 2.0
4 0.4
11 1.1
6 0.6
25 2.5
25 2.5
25 2.5
11 1.1
Note
Note
L243
Note
L243
L243
L243
L648
L574
L243
=
FOLLOW
2 - 49