Configuring Your Headset; Redial; Voice Dial; Battery Type - 3M Peltor WS ProTac XPI Manual

2:18 Redial (fig. 7)
The last dialed number on a phone connected via
Bluetooth can be redialed. Press and hold the Bluetooth
®
button for 2 seconds.
2:19 Voice dial (fig. 7)
To activate voice control of the last paired device, short
press the Bluetooth button.
®
3. CONFIGURING YOUR HEADSET (fig. 8)
Settings are changed in the menu. Press and hold the [+]
and [–] buttons for approximately 2 seconds to access the
menu. To step through the menu, press the On/Off/Mode
button briefly. The menu steps are listed below. At each
menu step the [+] and [–] buttons are used to change the
setting and step through the available settings. A voice
message confirms each menu step. After ten seconds of
inactivity, the menu returns to volume mode.
3:1 Bluetooth pairing (fig. 6)
®
When the voice message says "Bluetooth
press (1 s) the [+] button to start pairing. Short press (1 s)
the Bluetooth button to stop pairing. A voice message will
®
confirm, "Bluetooth pairing on". Search and select "WS
®
ProTac XPI" on your Bluetooth
will confirm when pairing is complete, "pairing complete"
and "connected". Short press (1 s) the [–] button to stop the
pairing. A voice message will confirm, "pairing failed".
3:2 VOX (voice operated transmission)
VOX enables automatic transmission when the sound level
at the microphone is above the VOX level. This allows radio
transmission without pressing the Bluetooth
are two settings: off mode (default) and on mode for
activating voice operated transmission.

3:3 Battery type

Battery type adjusts the indication of low battery warning for
different types of battery. It is adjustable for two types of
batteries: rechargeable and alkaline.
3:4 Reset (reset to factory default) (fig. 9)
To confirm a reset to factory default, hold the [+] button for
two seconds.
4. SETUP MODE (fig. 10)
To access the setup mode, the headset must be turned off. Then
press and hold the On/Off/Mode button and Bluetooth
approximately 2 seconds to start the headset in setup mode.
Press and hold the [+] and [–] buttons for approximately 2
seconds to access the extended menu.To step through the
menu, press the On/Off/Mode button briefly. The menu steps
are listed below. At each menu step, the [+] and [–] buttons are
used to change the setting and step through the available
settings. A voice message confirms each menu step. After ten
seconds of inactivity, the menu returns to volume mode.
®
pairing", short
®
device. A voice message
®
button. There
®
button for
®
4:1 Bluetooth pairing
®
When the voice message says "Bluetooth
press (1 s) the [+] button to start pairing. Short press (1 s)
the Bluetooth button to stop pairing. A voice message will
®
confirm, "Bluetooth pairing on". Search and select "WS
®
ProTac XPI" on your Bluetooth
will confirm when pairing is complete, "pairing complete"
and "connected". Short press (1 s) the [–] button to stop the
pairing. A voice message will confirm, "pairing failed".
4:2 VOX (voice operated transmission)
VOX enables automatic transmission when the sound level
at the microphone is above the VOX level. This allows radio
transmission without pressing the Bluetooth
are two settings: off mode (default) and on mode for
activating voice operated transmission.
4:3 Battery type
Battery type adjusts the indication of low battery warning for
different types of battery. It is adjustable for two types of
batteries: rechargeable and alkaline.
4:4 Reset (reset to factory default) (fig. 9)
To confirm a reset to factory default, hold the [+] button for
2 seconds.
4:5 VOX mode
Enable or disable the VOX function.
NOTE: When disabled, this will not be availabe in the menu.
4:6 Automatic power off
The automatic power off is the time that elapses before the
headset is automatically powered off if no buttons are
pressed or if there is no transmission made. There are two
settings: off and 4 hours (default).
4:7 Bluetooth streaming
®
Enable or disable the streaming function. Disable is default.
4:8 Bluetooth Multipoint
®
Enable or disable the Multipoint function. Disable is default.
4:9 Microphone volume
Increase or decrease the microphone gain.
4:10 LED On/Off/Mode button
The On/Off/Mode button is illuminated by a Light Emitting
Diode (LED) which indicates that the headset is powered on.
6
EN
pairing", short
®
device. A voice message
®
button. There
®