Specifications Exterior Lamps - Chrysler Concorde 2004 Service Manual

8L - 4 LAMPS/LIGHTING - EXTERIOR
LAMPS/LIGHTING - EXTERIOR (Continued)
(3) Check for battery voltage at the fused B(+) fuse
in the PDC. If OK, go to Step 4. If not OK, repair the
open B(+) circuit between the PDC and the battery
as required.
(4) Turn the ignition switch to the ON position.
Check for battery voltage at the fused ignition switch
output (RUN-ACC) fuse in the JB. If OK, go to Step
5. If not OK, repair the open fused ignition switch
output (RUN-ACC) circuit between the JB and the
ignition switch as required.
(5) Turn the ignition switch to the OFF position.
Disconnect and isolate the battery negative cable.
Remove the combination flasher from the rear of the
multi-function switch and replace it with a known
good unit. Reconnect the battery negative cable. Test
the operation of the turn signal and hazard warning
systems. If OK, discard the faulty combination
flasher. If not OK, remove the test flasher and go to
Step 6.
(6) Turn the ignition switch to the ON position.
Check for battery voltage at the fused ignition switch
output (RUN-ACC) circuit in the rear of the multi-
function switch for the combination flasher. If OK, go
to Step 7. If not OK, repair the open fused ignition
switch output (RUN-ACC) circuit between the combi-
nation flasher and the fused ignition switch output
(RUN-ACC) fuse in the JB as required.
(7) Turn the ignition switch to the OFF position.
Check for battery voltage at the fused B(+) circuit
cavity of the instrument panel wire harness connec-
tor for the combination flasher. If OK, go to Step 8. If
not OK, repair the open fused B(+) circuit between
the combination flasher and the fused B(+) fuse in
the PDC as required.
(8) Disconnect the instrument panel wire harness
connector for the multi-function switch. Check for
continuity between the hazard flasher signal circuit
in the instrument panel wire harness connector and
the instrument panel wire harness connector for the
multi-function switch. There should be continuity. If
OK, go to Step 9. If not OK, repair the open hazard
flasher signal circuit between the combination
flasher and the multi-function switch as required.
(9) Check for continuity between the right turn
switch sense circuit in the instrument panel wire
harness connector and the instrument panel wire
harness connector for the multi-function switch.
Repeat this check between the left turn switch sense
circuit cavities. If OK, go to Step 10. If not OK,
repair the open right and/or left turn switch sense
circuit(s) between the combination flasher and the
multi-function switch as required.
(10) Check for continuity between the right and/or
left turn signal circuit in the instrument panel wire
harness connector for the combination flasher and
the individual turn signal lamps. There should be
continuity. If OK, test the multi-function switch
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
EXTERIOR/MULTI-FUNCTION SWITCH - DIAG-
NOSIS AND TESTING). If not OK, repair the open
right and/or left turn signal circuit(s) between the
combination flasher and the turn signal lamp(s) as
required.
SPECIFICATIONS
EXTERIOR LAMPS
CAUTION: Do not use bulbs other than those listed
in the Bulb Application Table. Damage to lamp can
result.
Do not touch halogen bulbs with fingers or other
oily surfaces. Bulb life will be reduced.
BULB APPLICATION TABLE
LAMP
Back up
CHMSL
Front Parking/Turn
Signal
Front Parking/Turn
Signal/Side Marker
Front Side Marker
Fog lamps
Headlamps
License Plate
Spot Lamp
Tail
Tail Side Marker
MODEL BULB
Concorde/
Limited
Intrepid/300M 3157K
Concorde/
Limited/300M
Intrepid
300M
Limited 3157 AK or
Concorde/ 3157 K
300M
Intrepid 3157 KNA or
Limited
Intrepid H-3 (35 watt)
300M H-3 (55 watt)
Limited 9040 (40
Watt)
High Beam 9005 XSLL
(All)
Low Beam (All) 9006 XS
All
Intrepid - H3 (100 watt)
Police
300M 3157K
Intrepid
LH
921
921
912
921
NA
AK
168
168
168