Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 How To Use This Manual ....4 INTRODUCTION Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Warnings And Cautions
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label as a convenient record of your vehicle identification number and optional...
Page 7: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....9 ▫ Keys ....... 9 ▫...
Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Windows ......18 Rear Liftgate Release ....19 Occupant Restraints .
Page 9: Things To Know Before Starting Your Vehicle 7
A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from an authorized dealer.
Page 10: Ignition Key Removal
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Turning the key in the steering lock to the ON/RUN position deactivates the start lock-out. NOTE: In case the engine cannot be started, and START and ERROR are shown in the odometer display field, the system is not operational.
Page 11: Door Locks
To unlock the glove compartment, turn the key to the horizontal or left position, and then remove the key. DOOR LOCKS The vehicle doors can be locked when the doors are closed by either manually pressing the button down at the top of the door panel, pressing and releasing the bottom portion of the central locking switch located in the console, or by pressing and releasing the Lock...
Page 12: Central Locking Switch
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: In case of a malfunction in the central locking system, the doors can be locked and unlocked individu- ally. To lock, turn the key in the driver’s door lock clockwise, or push down the lock buttons. To unlock, turn the key in the driver’s door lock counterclockwise, or pull the inside door handles.
Page 13: General Notes On The Central Locking System
locking feature and neither door is opened, the doors remain unlocked even at vehicle speeds of approximately 9 mph (15 km/h) or more. NOTE: If you attempt to lock the doors with the key in the ignition and the driver’s door open, the doors will not lock.
Page 14: Remote Keyless Entry
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY This feature allows you to lock or unlock the vehicle from remote locations using a hand-held transmitter located in the key fob. You don’t have to point the transmitter at the vehicle to activate the system.
Page 15: Panic Alarm
If the vehicle cannot be locked or unlocked by pressing the transmit button, then it may be necessary to change the batteries in the remote control. Panic Alarm The panic alarm unlocks the driver’s door, turns on the interior lights, flashes the foglights and sounds the horn for about three minutes or until the alarm is turned off.
Page 16: Transmitter Battery Service
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. Transmitter Battery Service The recommended replacement Lithium battery is Pana- sonic CR 2025 or equivalent. To change the batteries: •...
Page 17: Security Alarm System
approximately 30 seconds, insert the key in the ignition and turn it to the ON/RUN position. The remote control should once again be operational. SECURITY ALARM SYSTEM The system monitors the doors, rear liftgate, hood, and ignition for unauthorized operation. The security alarm system is automatically armed or disarmed with the remote control or any of your vehicle’s keys by locking or unlocking the vehicle.
Page 18: Power Windows
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The tow-away alarm remains switched off until the vehicle is locked again with the key or the remote control, at which time it is automatically reactivated. POWER WINDOWS The power window switches are located in the console. To operate, turn the key in the ignition switch to the ACC or ON/RUN position.
Page 19: Rear Liftgate Release
When closing the windows, be sure that there is no danger of anyone being harmed by the closing proce- dure. WARNING! When leaving the vehicle, always remove the key from the ignition switch, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle.
Page 20: Occupant Restraints
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the lap/ shoulder seat belts for the driver and passenger, emer- gency tensioning retractors for the seat belts, and front and side airbags for the driver and passenger.
Page 21: Lap/Shoulder Belts
Lap/Shoulder Belts Each seating position is equipped with a combined lap/shoulder belt system. The belt webbing retractor will lock only during very sudden stops or impacts. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
Page 22 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 23 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 25: Seat Belts And Pregnant Women
WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.)
Page 26: Supplemental Restraint System (Srs) - Airbag
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for the driver and passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the steering wheel. The passenger frontal airbag is mounted in the instrument panel, under a cover marked SRS/AIRBAG.
Page 27 The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe front collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 29 These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. • The Occupant Restraint Controller also turns on the AIRBAG light in the instrument panel for four seconds when the ignition is first turned on, then turns the light off.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The knee impact bolster helps protect the knees and working with the seat belts, position you for the best interaction with the airbags. If a Deployment Occurs WARNING! Deployed airbags can’t protect you in another colli- sion.
Page 31 process that generates the nontoxic nitrogen gas used for airbag inflation. These airborne particles may irri- tate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers are designed to open only when the airbags are inflated.
Page 33 WARNING! • The door mounted side airbag deploys with con- siderable force. Being too close to the door panel during airbag deployment could cause serious injury or death. • All occupants must be in the appropriate restraint for their size and age, especially children 12 and under.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the airbag is turned off when there is any other occupant at that position, the supplemental restraint provided by the airbag will not be available. To turn OFF the passenger front airbag, use the on/off switch located on the instrument panel.
Page 35 • The switch does NOT turn off the side airbag. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To Turn On the Passenger Airbag: • Place the ignition key in the on/off switch, turn the key counterclockwise, and remove the key from the switch.
Page 36: Child Restraint
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbag is not there to protect you.
Page 37 WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A rearward facing infant restraint must not be used unless the passenger airbag has been shut off. A rearward facing infant restraint may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant.
Page 39 than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. (See LATCH - Child Seat Anchorage System section.) The belt-positioning booster seat is for children weighing more than 40 lbs. (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are general instructions, and not all child restraint sys- tems will be installed exactly as described here. Again, carefully follow the installation instructions that were provided with the child restraint system. The passenger seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean in to install the child restraint.
Page 41 equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE retractor action is restored. Any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. If your child restraint is equipped with a tether strap, attach it to the vehicle by first moving the seat back fully forward.
Page 43: Engine Break-In Recommendations
WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Deploying airbags could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
Page 44: Safety Tips
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
Page 45: Periodic Safety Checks You Should Make Outside The Vehicle
Defrosters Check operation by pressing the A/C control button, selecting the defrost mode and placing the blower control on high speed. You should be able to feel the air directed against the windshield. Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear or uneven wear...
Page 47 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Console Features ..... . .49 ▫ Storage Compartments ....49 ▫...
Page 48 48 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Instrument Panel Lighting ....61 ▫ Night Security Illumination ....61 Exterior Lights .
Page 49: Console Features
CONSOLE FEATURES The console has a power outlet/cigar lighter, an ash tray with a coin holder, a cupholder, and the passenger airbag light. In addition, there are switches to control the heated seats, rear spoiler, electronic stability program (ESP), hazard flashers, central locking, rear defroster and tow- ing alarm.
Page 50: 50 Understanding The Features Of Your Vehicle
50 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A cargo net for storage is located in the footwell area on the passenger side. Additionally, storage pockets are located on the wall behind each seat and on each door panel. A storage pouch is located on the rear wall between the seats, and the driver’s sunvisor has a document strap.
Page 51: Ashtray
Ashtray Lightly touch the bottom of the ashtray cover. The ashtray will open automatically. To remove the ashtray insert, pull the ashtray past the detent. Hold both sides of the insert, and pull up. To install the ashtray, place it in the frame and push down to engage.
Page 52: Coin Holder
52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coin Holder With the ashtray open, folding down the cover plate reveals the coin holder, which can accommodate nine coins in various sizes up to a U.S. quarter. The coin slots are shaped to retain the coins, and the cover plate ensures that the coins remain in the coin holder.
Page 53: Glove Compartment
Glove Compartment To lock the glove compartment, turn the key to the right and remove. To unlock, turn the key to the left and remove. Pull on the handle to open the glove compartment. CUPHOLDER The cupholder is located in the console. To open the cupholder, gently press downward on the front edge of the top panel, and then release.
Page 54: Mirrors
54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Adjusting The Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. Automatic Dimming Mirror Feature When the ignition switch is in the ON or RUN position, the automatic antiglare feature is activated.
Page 55: Exterior Mirrors Folding Feature
Exterior Mirrors Folding Feature All exterior mirrors are hinged to move forward or rearward to resist damage. The hinges have three detent positions: full forward, full rearward, and normal. Heated Remote Control Mirrors Both outside mirrors are heated to melt frost or ice when the Rear Window Defroster switch is depressed.
Page 56: Power Remote Control Outside Mirrors
56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Outside Mirrors The mirrors can be adjusted by using the remote control located in the console. Rotate the switch to the right to select the right mirror, rotate to the left to select the left mirror.
Page 57: Vanity Mirrors
Vanity Mirrors A vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and slide open the mirror cover. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 SEATS Driver Eight-Way Power Seat The switches to adjust the power seats are located on the outboard side of each seat.
Page 58: Passenger Four-Way Power Seat
58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passenger Four-Way Power Seat The switches to adjust the passenger seat are also on the outboard side of the seat. The passenger seat provides four-way adjustment - horizontal and back angle.
Page 59: Heated Seats
Heated Seats This feature heats the driver and passenger seats. The controls for the heated seats are located on the instrument panel, below the radio. After turning the ignition switch ON, you can choose the HI, LO, or OFF setting. Indicators on the switches show which setting has been selected.
Page 60: Interior Lights
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, close the hood by dropping it from approximately 12 inches (30 cm). WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving, and block your forward vi- sion.
Page 61: Front Map/Reading Lights
Front Map/Reading Lights These lights are located between the sun visors. A single centrally located switch operates both lights. Battery Saver Feature To prevent battery drain if a door is left open or ajar, the interior lights will turn off automatically after 15 minutes. After the door is closed, the interior lights will return to their normal function.
Page 62: Exterior Lights
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EXTERIOR LIGHTS Headlights and Parking Lights When the headlight switch is turned clockwise from OFF to the first position, the parking lights, taillights, side marker lights, license plate lights and instrument panel lights are all illuminated. The headlights turn on when the switch is turned to the second position.
Page 63: Fog Lights
Fog Lights To operate the fog lights, pull the headlight switch out one stop, with the parking lights and/or low beam headlights on. A light to the lower left of the headlight switch will illumi- nate when the fog lights are on. To turn off the fog lights, push the headlight switch in fully.
Page 64: Multifunction Control Lever
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MULTIFUNCTION CONTROL LEVER Turn Signals Move the multifunction control lever up to activate the right turn signal; move the lever down to activate the left turn signal. An arrow on the inside of the speedometer will flash to indicate operation.
Page 65: Headlight Dimmer Switch
Headlight Dimmer Switch Push the multifunction control lever toward the instru- ment panel to turn the headlights to high beam. Pull the lever toward you to switch to low beam. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction control lever toward the steering wheel.
Page 66: Windshield Wipers And Washer
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers And Washer The wipers and washer are operated by a switch in the multifunction control lever. Turn the end of the lever to select desired wiper speed: off, intermittent, normal, or fast.
Page 67: Telescoping Steering Column
WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Page 68: Tire Pressure Monitor System
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing. Adjusting the steering wheel while driving, or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle. NOTE: If the indicator light in the instrument cluster does not go out after starting the engine, the telescoping column is not locked properly.
Page 69 CAUTION! The TPM system is designed to monitor your tire pressure and will not function as a tire pressure gauge. After adjusting the air pressure in a tire, there will be a delay before the system updates the display. The TPM system will cause the indicator lamp in the instrument cluster to illuminate whenever the pressure in one tire falls 25% below the recommended pressure shown on the vehicle’s tire label.
Page 70 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and/or style.
Page 71: Rear Spoiler
REAR SPOILER A rear spoiler enhances vehicle stability. The rear spoiler deploys automatically when vehicle speed reaches 62 mph (100 km/h). The spoiler begins to retract at 39 mph (62 km/h). When retracted, the spoiler fits between the quarter panels, and aft of the liftgate window. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 The spoiler can also be deployed at lower speeds using an override switch mounted in the center console.
Page 72 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Should a malfunction occur that prevents the spoiler from deploying automatically, a red warning light will illuminate in the override switch and an audible warning will sound. WARNING! Do not drive the vehicle at speeds above 62 mph (100 km/h) if the red spoiler warning indicator is illumi- nated.
Page 73: Brake Assist System (Bas)
BRAKE ASSIST SYSTEM (BAS) WARNING! BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
Page 74: Electronic Stability Program (Esp)
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turned to the ON/RUN position. They should go out with the engine running. If the BAS/ESP malfunction indicator light comes on continuously with the engine running, a malfunction has been detected in either sys- tem.
Page 75 To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off the ESP system by pressing the upper half of the ESP switch. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 With the ESP system switched off, the engine torque reduction feature is cancelled.
Page 76: Synchronizing Esp
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE as possible. Be sure to adapt your speed and driving to the prevailing road conditions. When the ESP warning light is illuminated continuously, the ESP is switched off. To return to the enhanced vehicle stability offered by ESP, press the lower half of the switch (the ESP warning light in the speedometer dial goes out).
Page 77: Electronic Speed Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ELECTRONIC SPEED CONTROL The electronic speed control automatically maintains the set speed by actively regulating the throttle setting. Any speed above approximately 20 mph (30 km/h) can be maintained with the electronic speed control by operat- ing the lever.
Page 78: To Vary The Speed Setting
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To accelerate and set a speed, lift the lever up. Lift and hold the lever to accelerate, or lift and release to set a speed. To decelerate and set a speed, press the lever down.
Page 79: To Deactivate
To Deactivate A soft tap on the brake pedal, or normal brake pressure while slowing the vehicle, will deactivate the speed control without erasing the memory. Pushing the speed control lever forward or turning the key in the ignition switch to the OFF/LOCK position will turn off the speed control and erase the memory.
Page 80: Garage Door Opener
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use speed control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 81: Programming The Universal Transceiver
WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Step 3 does not have to be followed to program additional hand-held transmitters. 4. Choose one of the three buttons to program. Place the hand-held controller 1–3 inches (25–76 mm) from the universal transceiver while keeping its indicator light in view.
Page 83: Gate Operator/Canadian Programming
Programming Steps 8-10 to complete programming of a rolling code equipped device (most commonly a garage door opener). 8. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.
Page 84: Using The Universal Transceiver
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE signal has successfully been accepted by the universal transmitter. (The indicator light will flash slowly and then rapidly.) Proceed with Programming Step 6 to complete. Using the Universal Transceiver To operate the universal transceiver, simply press and release the programmed button.
Page 85: Security
Security If you sell your vehicle, be sure to erase the frequencies. To erase all of the previously programmed frequencies, hold down both outside buttons until the light begins to flash. This device complies with part 15 of FCC rules and with RS-210 of Industry Canada.
Page 87: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....88 Instrument Cluster ..... .89 Instrument Cluster Description .
Page 88: Instruments And Controls
88 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS...
Page 89: Instrument Cluster
INSTRUMENT CLUSTER The instrument cluster displays are activated by either opening the door, pressing the left button within the cluster, or turning the key in the ignition switch to the ON/RUN position. UNDERSTANDING YOUR INSTRUMENT PANEL 89 INSTRUMENT CLUSTER DESCRIPTION 1.
Page 90 90 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Low Tire Pressure Indicator Light The tire pressure monitor (TPM) system uses wireless technology to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to a receiver located in the vehicle. If the light is illuminated, the pressure in one of the tires on the vehicle has dropped to at least 25% below the recommended pressure on the vehicle’s tire label.
Page 91 WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radia- tor or coolant bottle is hot.
Page 92 92 UNDERSTANDING YOUR INSTRUMENT PANEL The arrows in the instrument cluster will flash in unison with the respective exterior turn signal. 7. Electronic Stability Program (ESP) Indicator Light The yellow ESP indicator light in the speedom- eter dial comes on with the key in the ignition switch turned to the ON/RUN position.
Page 93 WARNING! Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. NOTE: This light shows only that the parking brake is on.
Page 94 94 UNDERSTANDING YOUR INSTRUMENT PANEL 13. Brake Assist Indicator Light The indicator light for the Brake Assist Sys- tem (BAS) is combined with the Electronic Stability Program (ESP). This yellow indica- tor light in the instrument cluster comes on with the key in the ignition switch turned to the ON/RUN position.
Page 95 CAUTION! The accessory drive belt also drives the water pump. Operating the vehicle with a failed belt can cause engine overheating and possible severe engine dam- age. 16. High Beam Indicator Light This indicator will illuminate when the headlights are in the high beam setting. To activate the high beams, push the multifunction control lever past the point of resistance, toward the instrument panel.
Page 96 96 UNDERSTANDING YOUR INSTRUMENT PANEL • Press the button twice (with the key removed or in the OFF/LOCK or ACC position). 21. Main Odometer, Flexible Service System (FSS) This shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct distance that the vehicle has been driven.
Page 97 The counter can also be reset by any individual after the indicated service has been performed. To do so: 1. Turn key to the ON/RUN position. 2. Within one second press the knob/button twice. 3. The present status for days or distance is dis- played.
Page 98 98 UNDERSTANDING YOUR INSTRUMENT PANEL starts combined with short distance driving in which the engine does not reach normal operating temperature, reduce the interval between services. However you choose to set your reference numbers, the scheduled services as posted in the Service Booklet must be followed to properly care for your vehicle.
Page 99 the bulb is not lit during starting, have it replaced. If the light stays on, or comes on while driving, have the system checked by an authorized dealer. WARNING! In the event a malfunction of the airbag is indicated, the airbag may not be operational. For your safety, we strongly recommend that you visit an authorized dealer immediately to have the system checked;...
Page 100 100 UNDERSTANDING YOUR INSTRUMENT PANEL If the vehicle is not driving normally, and the Check Engine light flashes or remains on continuously, it is an alert to serious conditions that could lead to loss of power or severe catalytic converter damage. The vehicle should be serviced at an authorized dealer as soon as possible.
Page 101: Infinity Modulus" Am/Fm Stereo Radio With Single-Disc Cd Player
The indicated amount of oil must be added to the engine if the message -2.0 Q (-2.0L) blinks and a signal sounds. The HI message indicates that the excess oil must be removed from the pan to avoid possible engine or catalytic converter damage.
Page 102 102 UNDERSTANDING YOUR INSTRUMENT PANEL Power/Volume Control To activate the audio system, press the ON/OFF knob on the left. If the unit was switched off using the ignition switch, it will switch on again with the ignition switch. Press the ON/OFF knob within three seconds of turning the ignition switch off to prevent the radio from switch- ing off.
Page 103 NOTE: After six seconds without any action, or by pressing OPT, CD, AM, FM, or TP, the current setting is cancelled, and the new setting is stored. FM1 – FM2 – FM AS – BEST FM The system has four FM memory modes that can be selected by repeatedly pressing the FM button.
Page 104 104 UNDERSTANDING YOUR INSTRUMENT PANEL Beginning with the currently set frequency, the next station scanned will be heard for eight seconds. Press the right rotary control/push button if you wish to keep the current station. Once the scan begins, it will continue until either a station or program is retained or until another mode is selected.
Page 105 • REL MUSC – Religious Music • TOP 40 – Top 40 • REL TALK – Religious Talk • COUNTRY – Country Music • PERSNLTY – Personality • OLDIES – Oldies Format • PUBLIC – Public Radio • WEATHER – Weather Forecast •...
Page 106: Cd Player Operation
106 UNDERSTANDING YOUR INSTRUMENT PANEL General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
Page 107: User Menu
• Fast Forward/Rewind (<<, >>) Press and hold the multifunction button >> for audible fast forward play. Press and hold the multifunction button << for audible fast rewind play. The relative time is displayed during this operation and continues for an additional eight seconds after releasing the function button.
Page 108: User Memory (User - 1, 2, 3)
108 UNDERSTANDING YOUR INSTRUMENT PANEL User Memory (USER – 1, 2, 3) You can program up to three user memories, which saves the sound settings, and the last received station when the unit is switched off. To activate, first enter the user menu. One of the three users can now be selected by turning the right rotary/push button.
Page 109: Telephone Mute Characteristics
Telephone mute characteristics If a telephone with hands-free operation is installed, the call may be routed through the speaker system. This eliminates the need for an additional speaker (if the signal lines are connected to the unit). The following settings are available: •...
Page 110: Radio Antenna
110 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO ANTENNA The radio antenna is located in the rear liftgate glass and requires no maintenance. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio.
Page 111: Temperature Control
The climate control system allows you to balance the temperature, amount and direction of the air circulating throughout the vehicle. The system is always at operational readiness, except when manually switched off. The climate control only operates with the engine running. The climate control removes a considerable amount of moisture from the air during operation in the air condi- tioning mode, therefore it is considered normal operation...
Page 112: Basic Setting - Air Conditioner
112 UNDERSTANDING YOUR INSTRUMENT PANEL Select a temperature for each side of the pas- senger compartment. Select air volume with the fan control switch. Then select the Bi-Level setting on the air distribution control switch to force air from both the upper panel outlets and the floor outlets.
Page 113 Defrosting Set the temperature selectors to the maximum heating position, set the fan control to position 5, and the air distribution to the defrost position. Close the center air outlets. Close the left and right side air outlets. Turn the defroster outlets for the side windows to the detent position.
Page 114 114 UNDERSTANDING YOUR INSTRUMENT PANEL Ventilation To receive outside air through the panel outlets, turn off the Air Conditioning ON/OFF switch. The light in the switch should be off. Set the controls as above for basic air conditioning. Climate Control - OFF To switch the climate control off, set the air volume control switch to position 0.
Page 115 CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off by soaking with warm water. Air Recirculation/REST This mode can be selected to temporarily re- duce the entry of annoying odors or dust into the vehicle’s interior.
Page 116: Dust Filter
116 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: This vehicle is equipped with an air conditioner Operating Tips system that uses R-134a (HFC: hydrofluorocarbon) as a refrigerant. Repairs should always be performed by a qualified technician, and refrigerant should be collected in a recovery system for recycling. Dust Filter Nearly all dust particles and pollen are filtered out before outside air enters the passenger compartment through...
Page 117: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....119 ▫ Normal Starting ..... . 119 ▫...
Page 118 118 STARTING AND OPERATING ▫ Electronic Stability Program (ESP) ..133 ▫ Synchronizing ESP ....135 ▫...
Page 119: Starting Procedures
STARTING PROCEDURES WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. Be sure that the parking brake is engaged and that selector lever is in the NEUTRAL or PARK position (gearshift lever in Neutral).
Page 120: Extremely Cold Weather (Below -20°F Or -29°C)
120 STARTING AND OPERATING NOTE: Due to the starter non-repeat feature, the key must be turned completely to the left before attempting to start the engine again. Extremely Cold Weather (below -20°F or -29°C) For reliable starting in areas where temperatures fre- quently drop below -20°F (-29°C), we recommend the use of an externally powered battery and an electric engine block heater.
Page 121: After Starting
accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
Page 122: Recommended Shift Speeds
122 STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. Be sure the transmission is in FIRST gear, (not THIRD), when starting from a stopped position. Damage to the clutch can result from starting in THIRD.
Page 123: Automatic Transmission
WARNING! When leaving the vehicle, always remove the key from the ignition switch, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could move the gearshift lever, which could result in an accident or serious injury.
Page 124: Stopping
124 STARTING AND OPERATING The gear shifting process is continuously adapted, de- pendent on the driving style, the driving situation and the road characteristics. The selector lever is automatically locked while in the PARK position. To move the selector lever out of the PARK position, the brake pedal must be firmly depressed before the shift lock will release.
Page 125: Maneuvering
Maneuvering To maneuver in tight areas, control the vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly step on the accelerator. To rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying only slight acceleration.
Page 126: Reverse
126 STARTING AND OPERATING Reverse Shift into REVERSE gear only when the vehicle is com- pletely stopped. Dependent on the program mode selector switch position “S” or “W,” the maximum speed in the REVERSE gear is different. However, it is not possible to change the program mode while in REVERSE.
Page 127 into another gear that allows for quicker acceleration or to slow the vehicle down is possible. Downshifts can also be performed. Press and hold the selector lever in the “D-” direction. The transmission will shift from the current gear directly to the best gear for acceleration.
Page 128: Gear Ranges
128 STARTING AND OPERATING Gear Ranges “P” PARK NOTE: If the key is in the ON/RUN position, you must press the brake pedal to shift out of the PARK position. PARK supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion.
Page 129: Emergency Operation (Limp Home Mode)
Depressing the accelerator pedal rapidly or nearly to the floor while driving (kickdown position), rather than depressing the accelerator pedal in slow, small move- ments, will cause the automatic transmission to shift down into a lower gear. Rapid release of the accelerator pedal will normally result in an upshift.
Page 130: Parking Brake
130 STARTING AND OPERATING Have the transmission checked at your authorized dealer as soon as possible. PARKING BRAKE When you apply the parking brake with engine running, the brake system warning light in the instrument cluster will come on. NOTE: This light, when illuminated with parking brake application, shows only that the parking brake is on.
Page 131: Brake System
precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied when the driver is not in the vehicle. WARNING! Be sure the parking brake is fully disengaged before driving;...
Page 132 132 STARTING AND OPERATING BAS assistance. To receive the benefit of the system you must apply continuous, full braking power during the stopping sequence. Do not reduce brake pedal pressure. WARNING! BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
Page 133: Electronic Stability Program (Esp)
system. As a result, it is possible that only partial engine output will be available, and pressing the accelerator pedal will require more effort. If the BAS malfunctions, the brake system functions in the usual manner, but without BAS. With the ABS malfunctioning, the BAS and ESP will be disabled.
Page 134 134 STARTING AND OPERATING WARNING! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The ESP cannot prevent accidents, includ- ing those resulting from excessive speed in turns, or hydroplaning.
Page 135: Synchronizing Esp
Synchronizing ESP If the power supply was interrupted (battery discon- nected or discharged), the BAS/ESP malfunction indica- tor light may be illuminated with the engine running. To re-synchronize the ESP, and cancel the malfunction indi- cator light, the steering angle sensor will need to be recalibrated.
Page 136: Anti-Lock Brake System (Abs)
136 STARTING AND OPERATING illuminated. With the ESP system switched off, the en- gine torque reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. CAUTION! Snow chains should never be used without the recommended mud and snow (M+S) rated radial-ply tires.
Page 137 In the case of an emergency brake maneuver, keep continuous full pressure on the brake pedal. In this manner only can the ABS be most effective. On slippery road surfaces, the ABS will respond even with light brake pedal pressure because of the in- creased likelihood of locking wheels.
Page 138 138 STARTING AND OPERATING briefly during this procedure, or remains on after the engine is running, have the system checked by an autho- rized dealer. When the ABS malfunction indicator light in the instru- ment cluster comes on while the engine is running, it indicates that the ABS has detected a malfunction and has switched off.
Page 139: Brake Pad Break-In
WARNING! To use your brakes and accelerator more safely, follow these tips: • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. •...
Page 140: Tires
140 STARTING AND OPERATING TIRES Please take the time to read the tire warranty booklet in your Owner’s Manual package. It contains valuable information on tire maintenance. Specific recommendations on guidelines for long-term tire storage should be requested of the tire manufacturer. Please refer to the tire warranty booklet for contact information.
Page 141: Tire Inflation Pressures
3. Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortable ride. Both under-inflation and over-inflation affect the stability of the vehicle and can produce a feeling of sluggish response or over-responsiveness. Unequal tire pressures can cause erratic and unpredict- able steering response.
Page 142: Tire Pressure Monitor System
142 STARTING AND OPERATING Tire Pressure Monitor System The Tire Pressure Monitor System (TPM) monitors the pressure in all tires. The TPM system uses wireless technology to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to a computer which monitors for low pressure.
Page 143: High Speed Operation
Tire Chains The RUD-matic DISC is the only tire chain system approved for use on the Chrysler Crossfire. Chains should only be used on the rear wheels and only with the recommended winter mud and snow (M+S) tires and wheels. Follow the manufacturer’s mounting instructions.
Page 144: Original Equipment Tires
144 STARTING AND OPERATING When driving with tire chains, press the ESP control switch to OFF. CAUTION! Damage to the vehicle may result if unapproved tire chains are used. Original Equipment Tires Your vehicle is equipped with either sport performance tires or all-season performance tires.
Page 145: Tread Wear Indicators
tire also requires the purchase of two additional wheels with the same size specification as the original equip- ment front wheels. Snow tires may have a lower speed rating than factory equipped tires and may not match the maximum vehicle speed.
Page 146: Replacement Tires
146 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct inflation pressure. DaimlerChrysler Corporation strongly recommends that you use tires equivalent to the originals in size, quality and perfor- mance when replacement is needed (see the paragraph on tread wear indicators).
Page 147: Tire Rotation Recommendations
WARNING! Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 148 148 STARTING AND OPERATING Rotate your tires at intervals shown on the maintenance schedules. More frequent rotation is permissible if de- sired. The reasons for any rapid or unusual wear should be corrected before rotating.
Page 149: Alignment And Balance
If you experience these problems, try another brand of gasoline before consider- ing service for the vehicle. Over 60 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define...
Page 150: Reformulated Gasoline
150 STARTING AND OPERATING fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. DaimlerChrysler Corporation recommends the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning fuel, referred to as “Reformulated Gasoline”.
Page 151: Materials Added To Fuel
without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. DaimlerChrysler Corpo- ration recommends using gasolines without MMT. Since the MMT content of gasoline may not be indicated on the pump, you should ask your gasoline retailer whether or not his/her gasoline contains MMT.
Page 152: Adding Fuel
152 STARTING AND OPERATING CAUTION! If the CHECK ENGINE Light is flashing, immediate service is required. See the Onboard Diagnostic System (OBDII) paragraph in the Maintaining Your Vehicle section of this manual. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located under the fuel filler door, on the passenger’s side of the vehicle.
Page 153 If the warning light does not go out after starting the engine, or if it comes on while driving, it indicates that the fuel level is down to the reserve quantity of approxi- mately 2.1 gallons (8 liters). Leaving the engine running and the fuel cap open can cause the CHECK ENGINE light to illuminate.
Page 154: Vehicle Loading
154 STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is in the following chart and on the tire pressure label attached to the driver door pillar. Vehicle Loading Capacities Front Seat Occupants ..... . . 2 Cargo Capacity (with two persons) .
Page 155: Trailer Towing
WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof luggage rack “Cautions” when carrying cargo on your roof rack. TRAILER TOWING Trailer towing with your Crossfire is not recommended.
Page 157 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....158 If Your Engine Overheats ....158 TIREFIT Tire Repair And Jacking .
Page 158: 158 What To Do In Emergencies
158 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located in the console. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. Do not use this emergency warning system when the vehicle is in motion.
Page 159 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat.
Page 160: Tirefit Tire Repair And Jacking
160 WHAT TO DO IN EMERGENCIES TIREFIT TIRE REPAIR AND JACKING TIREFIT Small punctures, particularly those in the tread, can be sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -4°F (-20°C).
Page 161 WARNING! Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with ex- tremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving. TIREFIT should not be used in such circumstances. Do not drive the vehicle under such circumstances.
Page 162 162 WHAT TO DO IN EMERGENCIES 10. Insert the power plug (4) into the power point on the instrument panel. 11. Turn the ignition key to the ON/RUN position. 12. Press the switch on the air pump to 1. The air pump should start to inflate the tire.
Page 163: Preparations For Jacking
wheel components. Once TIREFIT sealing material has dried, it can easily be peeled off and properly discarded. Preparations for Jacking WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
Page 164: Jack Location And Instructions
164 WHAT TO DO IN EMERGENCIES • Turn off the engine. • Block the wheel diagonally opposite the flat tire. • Passengers must not remain in the vehicle when the vehicle is jacked. NOTE: The jack is designed exclusively for jacking up the vehicle at the specified jack location points built beneath either side of the vehicle.
Page 165 WHAT TO DO IN EMERGENCIES 165 2. The lifting points for the jack are located beneath the outer edge of the body side, directly behind the front wheel housings, and in front of the rear wheel housings.
Page 166 166 WHAT TO DO IN EMERGENCIES NOTE: Do not raise the vehicle until you are sure the jack is securely engaged, as shown. 3. Holding the jack, insert the cradle under the lifting points. Crank the handle clockwise until the jack base meets the ground.
Page 167: Jump-Starting The Battery
JUMP-STARTING THE BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start any time the ignition switch is on. You can be hurt by the fan. CAUTION! Do not try to push or tow your vehicle to get it started.
Page 168 168 WHAT TO DO IN EMERGENCIES 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch.
Page 169: Driving On Slippery Surfaces
6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fans. NOTE: If engine does not run after several unsuccessful starting attempts, have it checked at the nearest autho- rized dealer.
Page 170: Freeing A Stuck Vehicle
170 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE In order to free a stuck vehicle you must turn off the Electronic Stability Program (ESP) before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion.
Page 171: Towing Eyes
CAUTION! If the vehicle is towed with the front wheels raised, the engine must be shut off (key in the ignition switch turned to the OFF/LOCK or ACC positions). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. Switch off the tow-away alarm as well as the automatic central locking system.
Page 172 172 WHAT TO DO IN EMERGENCIES located behind the lower grille in the fascia. For access, a snap-in grille must be removed using the multifunction tool from the glovebox.
Page 173 WHAT TO DO IN EMERGENCIES 173 Insert the tool (or similar sized screwdriver) into the slot in the grille as shown, and rotate it to the left to detach. The front towing eye is now accessible.
Page 174: Tow-Away Alarm
174 WHAT TO DO IN EMERGENCIES Tow-Away Alarm Once the alarm system has been armed, the exterior vehicle lights will flash and an alarm will sound when anyone attempts to raise the vehicle for towing. The alarm will last approximately three minutes in the form of flashing exterior lights.
Page 175: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 3.2L Engine ......177 Onboard Diagnostic System (OBD II) ..178 Emissions Inspection And Maintenance Programs .
Page 176 176 MAINTAINING YOUR VEHICLE ▫ Manual Transmission ....200 ▫ Appearance Care And Protection From Corrosion ......201 Fuses .
Page 177: 3.2L Engine
MAINTAINING YOUR VEHICLE 177 3.2L ENGINE...
Page 178: Onboard Diagnostic System (Obd Ii)
178 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your Crossfire is equipped with a sophisti- cated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems.
Page 179: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the CHECK ENGINE Light is functioning and is not on when the engine is running, and that the OBD (Onboard Diagnostic) system is ready for testing.
Page 180: Replacement Parts
180 MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
Page 181: Maintenance Procedures
WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent technician.
Page 182 182 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Page 183 Change Engine Oil The oil change interval for your Crossfire is initially set at 7,000 miles (11,000 km). The Flexible Service System (FSS) in your vehicle evalu- ates engine temperature, oil level, vehicle speed, engine speed, distance driven, and the time elapsed since your last service.
Page 184 184 MAINTAINING YOUR VEHICLE Engine Oil Selection Only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40. The FFS may not alert for an oil change at the proper interval if an unapproved engine oil is used;...
Page 185 Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure. If adjustment is re- quired, adjust the belts according to the specifications and procedures shown in the Service Manual. Special tools are required to properly measure tension and to restore belt tension to factory specifications.
Page 186 186 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly serviced to assure proper catalyst operation and prevent possible catalyst damage. If the CHECK ENGINE light is flashing, immediate service is required.
Page 187: Ignition Wiring System
• Do not idle the engine with any spark plug wires disconnected for a prolonged period. Ignition Wiring System The ignition cables should be kept clean and properly connected. Terminals should be fully seated. Cracked, damaged, or faulty cables should be replaced. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits.
Page 188: Air Conditioner
188 MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Page 189: Power Steering Fluid
Power Steering Fluid No power steering fluid service is required. The system is filled at the factory with Pentosin CHF 11S. Steering noise and reduced component life may result if an unapproved fluid is used. During scheduled maintenance, check the power steering fluid level at the power steering fluid reservoir.
Page 190: Chassis Lubrication
190 MAINTAINING YOUR VEHICLE Chassis Lubrication Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints when- ever under-vehicle service is done. Steering Linkage Inspect tie rod ends whenever the vehicle is serviced. They are permanently lubricated and do not require periodic lubrication.
Page 191: Windshield Wiper Blades
lubricant. Repeat this procedure three or four times. Wipe all the lubricant off the key with a clean cloth, to avoid soiling clothing. Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner, or use the washer solvent.
Page 192: Windshield Washer Reservoir
192 MAINTAINING YOUR VEHICLE Windshield Washer Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) rated not to freeze at -25°F (-31°C).
Page 193: Cooling System
If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts.
Page 194 194 MAINTAINING YOUR VEHICLE Check the front of the radiator and condenser for an accumulation of bugs, leaves, etc. Clean the radiator and condenser by gently spraying water from a garden hose at the back of the radiator core. Check the recovery bottle tank tubing for condition and tightness of connection at the bottle and radiator.
Page 195 CAUTION! Failure to use the proper antifreeze could cause radiator plugging and engine overheating. Do not mix antifreeze brands or types. Do not use plain water alone or alcohol base antifreeze products. Do not use additional rust inhibitors or antirust prod- ucts, as they may not be compatible with the radiator coolant and may plug the radiator.
Page 196 196 MAINTAINING YOUR VEHICLE WARNING! Do not use a pressure cap other than the one speci- fied for your vehicle. Personal injury or engine damage may result. Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment.
Page 197: Hoses And Vacuum/Vapor Harnesses
Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, checking, tears, cuts, abrasions, and excessive swelling indicate deterioration of the rub- ber. Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold.
Page 198 198 MAINTAINING YOUR VEHICLE NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the hose-coupling area is not neces- sarily an indication of leakage.
Page 199: Automatic Transmission
Use brake fluid approved to MB 331.0, or a DOT 4 brake fluid with: minimum dry boiling point (ERBP) 500°F, minimum wet boiling point (WERBP) 356°F, maximum viscosity 1500 mm2/s, conforming to FMVSS 116 and ISO 4925. WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking.
Page 200: Manual Transmission
200 MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the fluid recommended by DaimlerChrysler Corporation may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmis- sion fluid other than that recommended by the DaimlerChrysler Corporation will result in more frequent fluid and filter changes.
Page 201: Appearance Care And Protection From Corrosion
CAUTION! Do not overfill. Dirt and water in the transmission can cause serious damage. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is seated properly. Add fluid, if necessary, to maintain the proper level. Frequency of Fluid Change Under normal operation conditions, the fluid installed at the factory will give satisfactory lubrication for the life of...
Page 202 202 MAINTAINING YOUR VEHICLE What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. •...
Page 203 • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Use Mopar touch-up paint on scratches or chips as soon as possible. Your dealer has touch-up paint to match the color of your vehicle.
Page 204 204 MAINTAINING YOUR VEHICLE • A car wash that uses carbide-tipped wheel cleaning brushes or acidic solutions. CAUTION! Many wheel cleaners contain acids that may harm the wheel surface. Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar Vinyl Cleaner to clean vinyl upholstery.
Page 205 Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.
Page 206: Fuses
206 MAINTAINING YOUR VEHICLE FUSES Engine Compartment Fuses The engine compartment fuses are located under the hood on the driver’s side, between the brake master cylinder and the left front fender. To remove the lid, squeeze the tabs together located at the front of the fusebox.
Page 207 MAINTAINING YOUR VEHICLE 207 CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected.
Page 208 208 MAINTAINING YOUR VEHICLE Engine Compartment Fuses Cavity Fuse Circuits 5 Amp Garage Door Opening Signal, Beige TPM and Seat Heater 5 Amp Occupant Restraint Controller Beige Passenger Airbag Off 5 Amp Indicator, Safety Restraint System Beige and Indicator, Passenger Airbag 30 Amp Wiper Motor Green...
Page 209 Cavity Fuse Circuits 10 Amp Spoiler Motor 30 Amp Seat Adjustment Right Side Green 30 Amp Seat Adjustment Left Side Green 15 Amp Sound Booster (Amplifier) Blue 30 Amp Seat Heater Green 20 Amp Pneumatic Control Unit, Rear Yellow Window Defroster 20 Amp Central Locking Yellow...
Page 210: Relay Control Module Fuses
210 MAINTAINING YOUR VEHICLE Relay Control Module Fuses The relay control module fuses are located in the Control Module Box next to the battery in the engine compart- ment. Slide the control module box cover retaining clips forward and lift the cover from the control module box to gain access to the relay control module fuses.
Page 211: Interior Fuses
Cavity Fuse Circuits 15 Amp Fuel Pump Blue 15 Amp Horn Blue Interior Fuses The fuse access door is located on the end of the instrument panel on the driver’s side behind the trim panel cover. Use a coin or flat blade screwdriver to open and close this access door.
Page 212: Replacement Bulbs
212 MAINTAINING YOUR VEHICLE Cavity Fuse Circuits 7.5 Amp Left High Beam Brown 15 Amp Right Low Beam Blue 7.5 Amp Right Parking/Tail Light Side Brown Marker 15 Amp Left Low Beam Blue 15 Amp Fog Light Blue 7.5 Amp Left Parking/Tail Light Side Brown Marker...
Page 213: Exterior Light Bulb Service
EXTERIOR LIGHT BULB SERVICE Headlights WARNING! Halogen lamps contain pressurized gas. A bulb can explode if you: • touch or move it when hot, • drop the bulb, • scratch the bulb Wear eye and hand protection. NOTE: To prevent a possible electrical short circuit, switch off light prior to replacing a bulb.
Page 214: Front Turn Signal And Parking/Standing Lights
214 MAINTAINING YOUR VEHICLE Front Turn Signal and Parking/Standing Lights • Twist the bulb socket counterclockwise and pull out. Push the bulb into the socket, turn counterclockwise and remove. • Replace the bulb, push in and twist clockwise. Rein- stall the socket, and turn clockwise. Front and Rear Sidemarker Lights 1.
Page 215: License Plate Light
4. Replace the access door in the trim panel. License Plate Light 1. Remove the two lens assembly mounting screws. 2. Pull the bulb out of the socket. 3. Replace the bulb and reattach the lens assembly. 4. Align and resecure the two lens assembly mounting screws.
Page 216: Vehicle Storage
216 MAINTAINING YOUR VEHICLE the vehicle and then readjust the headlights to the original position. If any further adjustments are neces- sary contact your manufacturer’s dealer. A detailed ser- vice procedure is contained in the manufacturer’s Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner’s Manual.
Page 217 Check the battery every four to six weeks to ensure that the voltage is above 12.40. Voltage will drop more rapidly in hot temperatures. If battery voltage drops below 12.40, follow the battery recharge procedure in the Service Manual. • Check that the radiator coolant level of protection is to at least -20°F (-29°C).
Page 218: Specifications
218 MAINTAINING YOUR VEHICLE SPECIFICATIONS Engine Specifications Engine Size 195.2 CID (3.2 Liters) Mode of Operation 4–stroke engine, gasoline injection No. of Cylinders Horsepower (SAE J 1349) 215 hp (160 kW) @ 5700 Bore 3.54 in. (89.90 mm) Stroke 3.30 in. (84.00 mm) Torque (SAE J 1349) 229 ft.
Page 219 Gear Ratios - 5-Speed Automatic Transmission First 3.95 Second 2.423 Third 1.486 Fourth 1.00 Fifth 0.833 Reverse 3.147/1.93 MAINTAINING YOUR VEHICLE 219 Body Specifications Overall Length 159.8 in. (4058 mm) Maximum Width 69.5 in. (1766 mm) Maximum Width With 76.9 in. (1954 mm) Mirrors Overall Height 51.5 in.
Page 220: Fluid Capacities
220 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Fuel Tank Reserve Engine Oil (with filter) 3.2 L Engine Cooling System * 3.2 L Engine Manual Transmission Automatic Transmission Rear Axle Power Steering Reservoir Brake Reservoir Windshield Washer Reservoir * Includes heater and coolant recovery bottle filled to MAX level. U.S.
Page 221: Recommended Fluids, Lubricants And Genuine Parts
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Use coolant approved to MB 325.0, such as Valvoline GO5, or an equivalent extended life coolant. Engine Oil Only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40.
Page 222: Chassis
222 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Brake Master Cylinder Clutch Fluid Manual Transmission Fluid Power Steering Reservoir Rear Axle Fluid Tire Pressure Fluids, Lubricants and Genuine Parts Only use ATF approved to MB 236.10, MB 236.12. Synthetic Dexron III Transmission Fluid may be substituted.
Page 223: Body
Body Component Fluids, Lubricants and Genuine Parts Hinges: Door Mopar Spray White Lube Liftgate / Decklid Mopar Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Hood Springs and Links Mopar Spray White Lube Latches: Liftgate/Decklid Mopar Spray White Lube Hood/Safety Catch Mopar Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Door Mopar Spray White Lube Seat Regulator and Track Mopar Multi-Purpose Lube NLGI Grade 2 EP, GC-LB...
Page 225 MAINTENANCE SCHEDULES CONTENTS Introduction ......226 Warranty ......226 Emission Control System Maintenance .
Page 226: Introduction
226 MAINTENANCE SCHEDULES INTRODUCTION This is intended as a guide to the service requirements of your vehicle. It contains all necessary instructions concerning service intervals and operations which have to be carried out. Scope and frequency of maintenance work primarily depend on the vehicle’s operating conditions.
Page 227: Emission Control System Maintenance
to be serviced and adjusted in accordance with special instructions and using special measuring equipment. Modifications to or interference with the emissions con- trol systems are not permissible. All DaimlerChrysler Corporation dealers are familiar with the relevant and applicable regulations. EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled”...
Page 228: Scope Of Work For "A" Schedule Maintenance Service
228 MAINTENANCE SCHEDULES Additional Periodic Maintenance items should also be performed beyond the items listed in the following charts to assure the optimum performance of your Crossfire. SCOPE OF WORK FOR “A” SCHEDULE MAINTENANCE SERVICE Oil Change • Change oil and replace filter Maintenance •...
Page 229 • Replace dust filter • Lubricate hood hinges, latch, and secondary latch • Reset FSS Display Function Check • Horn, hazard warning flashers, turn signals, and indi- cator lamps • Headlamps and exterior lighting • Windshield wipers and washer system •...
Page 230: Fss System
230 MAINTENANCE SCHEDULES • Hydraulic brake system • Power steering system • Windshield washer system FSS SYSTEM The Flexible Service System (FSS) permits a flexible service schedule that is directly related to the operating conditions of the vehicle. See the Understanding Your Instrument Panel section for details on how to use the FSS.
Page 231: Regular Check-Ups
Depending on operating conditions through- out the year, a clock symbol may appear next to the service symbol. When this occurs, the next service is calculated and displayed in days remaining before the next service is required. You should have the maintenance performed within the stated time period or distance.
Page 232: Additional Periodic Maintenance
232 MAINTENANCE SCHEDULES • Check the windshield washer solvent and add if required. • Inspect wiper blade condition. • Check operation of lighting systems. • Inspect tires for unusual wear, damage, and pressure (at least every 14 days). • Mechanical assemblies (e.g., engine, transmission, etc.) - check for leaks.
Page 233: Special Maintenance Requirements
At approximately every 60,000 miles (96,000 km) or 4 years: • Replace fuel filter. • Replace air cleaner filter element. At approximately 80,000 miles (129,000 km): • Change the automatic transmission fluid and filter. After this change it is filled for life. The manual transmission comes filled for life from the factory.
Page 234: 234 Maintenance Schedules
234 MAINTENANCE SCHEDULES Dust Filter for Heating/Ventilation Replacement The dust filter is replaced during routine maintenance service. The filter element must be replaced with “B” Schedule service or every 18,500 miles (30,000 km) to maintain effectiveness. However, if operating conditions are dusty, these filters should be replaced more fre- quently.
Page 235 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......236 ▫...
Page 236: Suggestions For Obtaining Service For Your Vehicle
236 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty;...
Page 237: If You Need Consumer Assistance 237
This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
Page 238 238 IF YOU NEED CONSUMER ASSISTANCE conventional teletypewriter (TTY) in the United States can communicate with the DaimlerChrysler Corpora- tion by dialing 1-800-380-CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your DaimlerChrysler Corpo- ration’s new vehicle limited warranty expires.
Page 239: Warranty Information
IF YOU NEED CONSUMER ASSISTANCE 239 WARRANTY INFORMATION See your DaimlerChrysler Corporation Warranty Infor- mation Booklet for more information on warranty cover- age and transfer of warranty.
Page 240: Mopar Parts
240 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 states of the United States and Washington, D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety...
Page 241: Department Of Transportation Uniform Tire Quality Grades
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 242: Traction Grades
242 IF YOU NEED CONSUMER ASSISTANCE (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
Page 243: Index
INDEX...
Page 244 244 INDEX ABS (Anti-Lock Brake) System ....93 Adding Engine Coolant (Antifreeze) ..195 Adding Fuel ......152 Aiming Headlights .
Page 245 Carbon Monoxide Warning ....44 Cargo Compartment Capacity ......154 Catalytic Converter .
Page 246 246 INDEX Driving On Slippery Surfaces ....169 Electronic Speed Control ....77 Electronic Stability Program .
Page 247 Gear Ratios ......218 Glass Cleaning ......205 Glove Compartment .
Page 248 248 INDEX Fog ....... . 63 Hazard Warning Flasher ....158 Headlights .
Page 249 Materials Added to ....184 Recommendation ..... 184 Oil Filter, Selection .
Page 250 250 INDEX Inspection ......44 Maintenance ......205 Operating Instructions .
Page 251 Snow Tires ......144 Spinning ......143 Tread Wear Indicators .

Chrysler 2004 Crossfire Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Maintenance Schedules

If You Need Consumer Assistance

9 If You Need Consumer Assistance

10 Index

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Chrysler 2004 Crossfire

Summary of Contents for Chrysler 2004 Crossfire