Operation; Diagnosis And Testing - Memory Set Switch; Removal; Installation - Chrysler Concorde 2004 Service Manual

LH
MEMORY SET SWITCH (Continued)

OPERATION

When the memory set/selector switch is depressed,
a resistance signal is sent to the memory heated seat
mirror module via hard wired connections. The mod-
ule than receives this hard-wired input and applies
power to move the power seat track or side view mir-
rors according to the preset position. When the mem-
ory system is in "set" mode a chime will be generated
by the body control module.
See the owner's manual in the vehicle glove box for
more information on the features, use and operation
of the memory switch.
DIAGNOSIS AND TESTING - MEMORY SET
SWITCH
For complete circuit diagrams, refer to Wiring
Diagrams.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the driver side front seat side shield.
Refer to Body for the procedure.
(3) Disconnect the memory switch wire harness
connector from the memory switch.
(4) Use an ohmmeter to test for continuity
between the memory switch terminals.
(5) Connect one end of the ohmmeter to pin #3.
While holding the memory 1 button check for conti-
nuity with pin #6. If not OK, replace the faulty mem-
ory switch.
(6) Connect one end of the ohmmeter to pin #3.
While holding the memory 2 button check for conti-
nuity with pin #4. If not OK, replace the faulty mem-
ory switch.
(7) Connect one end of the ohmmeter to pin #3.
While holding the memory S button check for conti-
nuity with pin #5. If not OK, replace the faulty mem-
ory switch.
(8) If OK, refer to Memory System Diagnosis
and Testing in this group. If not OK, replace the
faulty memory switch.

REMOVAL

(1) Disconnect and isolate the negative battery
cable remote terminal from the remote battery post.
WARNING: SOME VEHICLES ARE EQUIPPED WITH
SEATBACK MOUNTED
ATTEMPTING TO DIAGNOSE OR SERVICE ANY
SEAT OR POWER SEAT SYSTEM COMPONENT
YOU MUST FIRST DISCONNECT AND ISOLATE THE
BATTERY NEGATIVE CABLE. THEN WAIT TWO MIN-
UTES FOR THE SYSTEM CAPACITOR TO DIS-
CHARGE BEFORE FURTHER SYSTEM SERVICE.
THIS IS THE ONLY SURE WAY TO DISABLE THE
AIRBAG SYSTEM. FAILURE TO DO SO COULD
AIRBAGS. BEFORE
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(2) Remove the drivers seat cushion side shield
from the seat (Fig. 2). Refer to the Body section for
the procedure.
Fig. 2 Memory, Power and Heated Seat Switch
Locations
1 - HEATED SEAT SWITCH
2 - POWER SEAT SWITCH
3 - SEAT CUSHION SIDE SHIELD
4 - MEMORY SET SWITCH
(3) From the bottom, disengage the memory set
switch by gently rock through the opening.

INSTALLATION

(1) Install the switch in the seat cushion side
shield.
(2) Install the seat cushion side shield. Refer to
the Body section for the procedure.
(3) Connect the negative battery cable remote ter-
minal.
DRIVER POWER SEAT SWITCH
DESCRIPTION
Vehicles equipped with power seats utilize a eight-
way driver power seat switch. This eight-way power
seat switch features two knobs ganged together on
the outboard seat cushion side shield.
The switch is secured to the back of the seat cush-
ion side shield with two screws. However, the control
knobs for the eight-way power seat switch unit must
be removed before the seat switch can be removed
from the side shield.
The power seat switch cannot be repaired. If one
switch is damaged or faulty, the entire power seat
switch assembly must be replaced.
OPERATION
When a power seat switch control knob or knobs
are actuated, a battery feed and a ground path are
applied through the switch contacts to the power seat
track or recliner adjuster motor. The selected
adjuster motor operates to move the seat track or
recliner through its drive unit in the selected direc-
POWER SEATS 8N - 15