Installation; Washer Fluid Level Switch Removal; Washer Fluid Level Switch - Intrepid Removal; Washer Hoses Removal - Chrysler Concorde 2004 Service Manual

LH
HEADLAMP WASHER PUMP - EXPORT (Continued)

INSTALLATION

(1) Install the headlamp washer motor in the
windshield/headlamp washer pump.
(2) Connect the headlamp washer pump hose and
electrical connector.
(3) Install the reservoir retaining bolts. Torque
bolts to 5 to 7 N·m.
(4) Reinstall the front fascia as necessary. Refer to
Body for Installation procedures.
(5) Lower vehicle from hoist.
(6) Refill the windshield/headlamp washer reser-
voir.
(7) Reconnect the negative battery cable remote
terminal.
(8) Prime the headlamp washer system. Refer to
the Electrical, Wipers/Washerr, Headlamp Washers,
Standard Procedures - Headlamp Washer System
Priming.
WASHER FLUID LEVEL
SWITCH
REMOVAL
(1) Open hood and disconnect the negative battery
cable remote terminal from the remote battery post.
(2) Hoist vehicle.
(3) Remove front fascia as necessary (left side only
and use a 2x4 to prop left edge of fascia away from
body). Refer to Body for Removal.
(4) Disconnect the wire connector from the reser-
voir fluid level sensor.
(5) Gently pry sensor away from reservoir and out
of grommet. Care must be taken not to puncture res-
ervoir (Fig. 8).
(6) Remover rubber grommet from reservoir and
throw away.
INSTALLATION
NOTE: Use a new mounting grommet when install-
ing a new sensor assembly.
Assure "flat" of sensor is aligned under the "ridge"
of reservoir and that sensor connector is facing down
in the fully seated position.
(1) Install new rubber grommet into reservoir.
(2) Carefully install sensor into reservoir and
grommet. Care must be taken not to puncture reser-
voir or grommet (Fig. 8).
(3) Connect the wire connector to the reservoir
fluid level sensor.
(4) Install the front fascia as necessary. Refer to
Body for Installation.
(5) Lower vehicle from hoist.
(6) Connect the negative battery cable remote ter-
minal to the remote battery post.
WASHER FLUID LEVEL
SWITCH - INTREPID
REMOVAL
(1) Open hood and disconnect the negative battery
cable remote terminal from the remote battery post.
(2) Remove the Washer Reservoir. Refer to Electri-
cal, Wipers and Washers, Washer Reservoir, Removal.
(3) Gently pry sensor away from reservoir and out
of grommet. Care must be taken not to puncture res-
ervoir (Fig. 8).
(4) Remover rubber grommet from reservoir and
throw away.
INSTALLATION
NOTE: Use a new mounting grommet when install-
ing a new sensor assembly.
Assure "flat" of sensor is aligned under the "ridge"
of reservoir and that sensor connector is facing down
in the fully seated position.
(1) Install new rubber grommet into reservoir.
(2) Carefully install sensor into reservoir and
grommet. Care must be taken not to puncture reser-
voir or grommet (Fig. 8).
(3) Connect the wire connector to the reservoir
fluid level sensor.
(4) Install the Washer Reservoir. Refer to Electri-
cal, Wipers and Washers, Washer Reservoir, Installa-
tion
(5) Connect the negative battery cable remote ter-
minal to the remote battery post.
WASHER HOSES
REMOVAL
(1) Remove left headlamp unit. Refer to Electrical,
Lamps/Lighting - Exterior, Headlamp Unit, Removal.
(2) Remove underhood silencer pad clips only
along left rear of hood.
(3) Carefully pull silencer pad away from hood.
(4) Disconnect "Y" connector from hood.
(5) Disconnect right and left hood nozzle hoses at
"Y" connector.
(6) Disconnect hose clips from hood, tower to tower
beam, and fender beam.
(7) Disconnect washer hose from top of reservoir
and from washer pump discharge port.
(8) Carefully pull washer hose up through engine
compartment.
WIPERS/WASHERS 8R - 15