Sis Command And Response Table For Basic Matrix Switcher Commands - Extron electronics XTP CrossPoint1600 User Manual

SIS Command and Response Table for Basic Matrix Switcher
Commands
The table that starts below shows commands for basic operation of the XTP CrossPoint
Series matrix switcher frame. Commands shown affect the entire matrix switcher, regardless
of the input boards and output boards installed or any connected endpoints.
Command Function
Create Ties
NOTES:
•
Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*8$.
•
The quick multiple tie and tie input to all output commands activate all I/O switches simultaneously.
•
The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1, 02*02, or 001*001).
•
The & tie command for RGB and the % tie command for video can be used interchangeably on the matrix switchers.
Tie input video and audio to output
Example:
Tie input video (RGB) only to output
Example (see last Notes bullet,
above):
Tie input video only to output
Example (see last Notes bullet,
above):
Tie input audio only to output
Example:
NOTE: Audio is not routed to an output HDMI connector if there is no video input tied to it. Insert a black video signal into audio
breakaway ties using the
an audio-only tie.
Untie input video and audio
Quick multiple tie
Example:
Tie input to all outputs, video and
audio
Example:
clears all ties.
NOTE: 0*!
Tie input to all outputs, RGB (video)
only
Example (see last Notes bullet,
above):
Tie input to all outputs, video only
Example (see last Notes bullet,
above):
Tie input to all outputs, audio only
NOTE: X! = Input number
X@ = Output number
SIS Command
(Host to Unit)
X! X@
* !
1*3!
X! X@
* &
10*4&
X! X@
* %
7*5%
X! X@
* $
12*4$
E
command on page 103
BAFMT
X@
0* !
E X! X@ X! X@ }
+Q * !... * $
E }
+Q3*4!3*5%3*6$
X!
*!
5*!
X!
*&
8*&
X!
*%
10*%
X!
*$
– , or
00 16, 32
01 – 16, 32 , or
Response
(Unit to Host)
X@ X! ]
Out •In •All
]
Out03•In01•All
X@ X! ]
Out •In •RGB
]
Out04•In10•RGB
X@ X! ]
Out •In •Vid
]
Out05•In07•Vid
X@ X! ]
Out •In •Aud
]
Out04•In12•Aud
E
and the commands on
EAFMT
X@ ]
Out •In00•All
]
Qik
]
Qik
X! ]
•All
In
]
In05•All
X! ]
In •RGB
]
In08•RGB
X! ]
In •Vid
]
In10•Vid
X! ]
In •Aud
( = untied)
64 00
64
XTP CrossPoint Series • Programming Guide
Additional Description
X!
Tie the input video and audio to
X@
output .
Tie input 1 video and audio to output 3.
Audio breakaway.
Tie input 10 RGB to output 4.
Audio breakaway.
Tie input 7 video to output 5.
Audio breakaway.
Tie input 12 audio to output 4.
page 97 and page 99 to make
Untie the video and audio input from
X@
output .
Tie input 3 video and audio to
output 4, tie input 3 video to output 5,
and tie input 3 audio to output 6.
Tie input 5 video and audio to all
outputs.
Audio breakaway.
Tie input 8 RGB to all outputs.
Audio breakaway.
Tie input 10 video to all outputs.
Audio breakaway.
87