Extron electronics XTP CrossPoint1600 User Manual page 100

Command Function
Inputs on XTP CP 4i HD 4K PLUS, XTP CP 4i HDMI, XTP CP 4i HDMI DMA, and XTP CP 4i DVI Pro
HDCP status
View input HDCP status
View HDCP status of all inputs
Inputs on XTP CP 4i [XTP], XTP CP 4i 4K [XTP], and XTP CP 4i Fiber 4K Boards
Captive screw and Ethernet serial port insertion enables
NOTE: See RS-232 Insertion
Enable an input captive screw serial
port insertion
Enable an input Ethernet serial port
insertion
Set all RS-232 input insertions
View input insertion
View all input insertions
Ethernet serial port insert parameters
Set serial port parameters
Read serial port parameters
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
Set UART starting point
Read UART starting point
:
X^ = Input number (for other than tie)
NOTE
X1# = HDCP status (for inputs)
X1$ = Captive screw or UART
X1% = Port number
X1^ = Baud rate
X1& = Parity
X1* = Data bits
X1( = Stop bits
X2) = Port timeout (10-sec. increments)
X2! = UART starting point
SIS Command
(Host to Unit)
Boards (continued)
E X^ }
I HDCP
E }
IHDCP
on page 66 for an overview of using serial port insertions.
E X^ }
I *0LRPT
E X^ }
I *1LRPT
E X1$ }
I *LRPT
E X^ }
I LRPT
E }
ILRPT
EX1% X1^ X1& X1* X1(
* , , , CP
EX1% }
CP
E X2) }
0* TC
E }
0TC
E X2) }
1* TC
E }
1TC
EX2! }
MD
E }
MD
—
01 16 or 32
= No source device connected
0
= Source connected is HDCP-compliant
1
= Source connected is not HDCP-compliant
2
= Captive screw RS-232 insert (default)
0
— 18 or 34 = UARTs (inputs) 1 — 16 or 32
03
300 , 600 , 1200 ,
, ,
38400 57600 115200
odd, even, none, mark, space (only the first letter is required) (n = default)
, 8 (default)
7
1 (default),
2
(= 10 seconds) -
1
The starting point (
The next position (
For the XTP CrossPoint 1600,
For the XTP CrossPoint 3200,
Default values:
Response Additional Description
(Unit to Host)
X1#]
X1# X1# X1# X1# ]
...
1 2 3 n
X^ ]
Enable the captive screw serial port
LrptI *0
insert on input
Ethernet RS-232 insert.
X^ ]
Enable the Ethernet serial port insert
LrptI *1
on input
screw serial port insert.
X1$]
LrptI00*
X1$]
X1$ X1$ X1$ X1$ ]
One
1 2 3 ... n
input, starting at input 1. Inputs that are
not on an XTP CP 4i [XTP], XTP CP 4i
4K [XTP], or XTP CP 4i Fiber 4K board
report as 0.
}
X1% X1^ X1& X1* X1(]
Cpn •Ccp , , ,
X1^ X1& X1* X1(]
, , ,
X2)]
Pti0*
X2)]
X2)]
Pti1*
X2)]
X2!]
Sets the initial (lowest) port number for
Pmd
the range of numbers assigned to the
serial port and UARTs.
X2!]
= Ethernet RS-232 insert (UART)
1
1800 , 2400 , 3600 , 4800 , 7200 , 9600
(default is = 300 seconds = 5 minutes)
65000 30
X2! ) is the rear panel RS-232/RS-422 port.
X2! ) is not used.
+1
X2! through X2!
+2 +17
X2! through X2!
+2 +33
= Rear panel remote RS-232/RS-422 port
1999
2000 is unused
through (XTP CrossPoint 1600) = Input 1 through 16
2001 2016
through (XTP CrossPoint 3200) = Input 1 through 32
2001 2032
XTP CrossPoint Series • Programming Guide
X^
. This disables the
X^
. This disables the captive
X1$
for each available (installed)
(default), 14400 , 19200 , 28800
are XTP inputs.
are XTP inputs.
,
92