Extron electronics XTP CrossPoint1600 User Manual page 109

Command Function
Horizontal shift
Specify a value
Increment value
Decrement value
View
Vertical shift
Specify a value
Increment value
Decrement value
View
Save and recall analog input presets
NOTES:
•
Analog input presets are available for analog (RGB, YUVp, YUVi, S-video, composite) video input signals on an XTP CP 4i VGA
universal analog input board only.
•
Analog input presets save a set of analog variables, such as: horizontal and vertical shift, pixel phase, color and tint, brightness
and contrast, and input type.
Save an analog input preset
Recall an analog input preset
Input sync detection
View all input connections
Example
(XTP CrossPoint 3200):
XTP T FB 202, XTP T FB 202 4K, XTP T UWP 202, XTP T UWP 202 4K, XTP T UWP 302,
XTP T EU 202, and XTP T MK 202 switcher commands
Audio routing selections
Enable black signal for XTP T
endpoint
Disable black signal for XTP T
endpoint
View black signal output status for
XTP T endpoint
Input reports as an HDCP-authorized device
HDCP authorized device on
HDCP authorized device off
View HDCP authorized status
:
NOTE X% = Input signal status
X^ = Input number (for other than tie)
X1@ = HDCP authorized device
X2@
= Enable or disable black video ties
X3@ = Shift
X3# = Analog input preset
SIS Command
(Host to Unit to Endpoint)
XTP T VGA transmitter commands (continued)
E X^ X3@ }
I * HCTR
E X^ }
I –HCTR
E X^ }
I +HCTR
E X^ }
I HCTR
E X^ X3@ }
I * VCTR
E X^ }
I +VCTR
E X^ }
I –VCTR
E X^ }
I VCTR
X^ X3#
*1* ,
X^ X3#
*1* .
0LS
0LS
E X^ }
E *1AFMT
E X^ }
E *0AFMT
E X^ }
E *AFMT
E X^ }
E *1HDCP
E X^ }
E *0HDCP
E X^ }
E HDCP
= No signal detected
0
01 – 16 or 32
= Off
0
0
= Disable
through
0 65535
1 through 8
Response Additional Description
(Endpoint to Unit to Host)
X^ X3@] Set the horizontal location of first active
HctrI *
pixel in input
X^ X3@]
Increase the value by one pixel (shift the
HctrI *
image to the right).
X^ X3@] Decrease the value by one pixel (shift
HctrI *
the image to the left).
X3@]
Show the horizontal location of first
active pixel in input
X^ X3@]
Set the vertical location of first active
VctrI *
pixel in input
X^ X3@]
Increase the value by one line (shift up).
VctrI *
X^ X3@]
Decrease the value by one line (shift down).
VctrI *
X3@]
Show the vertical location of first active
pixel in input
X^ X3#]
Spr *1* Command character is a comma.
X^ X3#]
Rpr *1*
Command character is a period.
X% X% X% X% ]
... 16 or
1 2 3 n
status of an input, starting from input 1.
Sync detected
No input detected
0 0 0 1 1 1 0 1 0 0 1 0 1. . .0
Response Status:
Input: 1 2 3 4 5 6 7 8 9 10111213
X^ ]
Enable an audio only tie for the
AfmtE *1
connected XTP transmitter.
X^ ]
Disable an audio only tie for the
AfmtE *0
connected XTP transmitter.
X2@]
The black signal status of XTP
transmitter endpoint
X^ ]
Set the input as an HDCP authorized device.
HdcpE *1
X^ ]
Set the input as not an HDCP
HdcpE *0
authorized device.
X1@]
Show HDCP authorized device status.
= Sync detected
1
= On (default)
1
1
= Enable
XTP CrossPoint Series • Programming Guide
X^
.
X^
.
X^
.
X^
.
X%
32 ( ) s; each is the connection
n
Sync detected
32
X^ X2@
is .
101