Siemens SIPART PS2 Operating Instructions Manual page 9

10.2.4.7 Diagnostic value '8.WAY - Determined travel' ...................................................................... 212
10.2.4.8 Diagnostic value '9.TUP - Travel time UP' / '10.TDOWN - Travel time DOWN' ................... 212
10.2.4.9 Diagnostic value '11.LEAK - Leakage test' ........................................................................... 212
10.2.4.10 Diagnostic value '12.PST - Monitoring of partial stroke test' ................................................ 214
10.2.4.11 Diagnostic value '13.PRPST' - Time since last partial stroke test' ....................................... 215
10.2.4.12 Diagnostic value '14.NXPST - Time until next partial stroke test' ......................................... 215
10.2.4.13 Diagnostic value '15.DEVI - General control valve fault' ...................................................... 215
10.2.4.14 Diagnostic value '16.ONLK - Pneumatic leakage' ................................................................ 216
10.2.4.15 Diagnostic value '17.STIC - Stiction (slipstick)' ..................................................................... 216
10.2.4.16 Diagnostic value '18.ZERO - Lower endstop' ....................................................................... 216
10.2.4.17 Diagnostic value '19.OPEN - Upper endstop' ....................................................................... 216
10.2.4.18 Diagnostic value '20.PAVG - Average value of position' ...................................................... 217
10.2.4.19 Diagnostic value '21.P0 - Potentiometer value of lower endstop (0%)' / '22.P100 -
Potentiometer value of upper endstop (100%)' .................................................................... 218
10.2.4.20 Diagnostic value '23.IMPUP - Impulse length UP' / '24.IMPDN - Impulse length
DOWN' .................................................................................................................................. 219
10.2.4.21 Diagnostic value '25.PAUTP - Pulse interval' ....................................................................... 220
10.2.4.22 Diagnostic value '26.DBUP - Deadband UP' / '27.DBDN - Deadband DOWN' .................... 220
10.2.4.23 Diagnostic value '28.SSUP - Slow step zone UP' / '29.SSDN - Slow step zone DOWN' ..... 220
10.2.4.24 Diagnostic value '30.TEMP - Current temperature' .............................................................. 221
10.2.4.25 Diagnostic value '31.TMIN - Minimum temperature' / '32.TMAX - Maximum
temperature' .......................................................................................................................... 221
10.2.4.26 Diagnostic value '33.T1' ... '41.T9' - Number of operating hours in the temperature
range 1 to 9 ........................................................................................................................... 221
10.2.4.27 Diagnostic value '42.VENT1' / '43.VENT2' ........................................................................... 222
10.2.4.28 Diagnostic value '44.VEN1R' / '45.VEN2R' ........................................................................... 222
10.2.4.29 Diagnostic value '46.STORE - Save maintenance data' ...................................................... 223
10.2.4.30 Diagnostic value '47.PRUP - Prediction UP' / '48.PRDN - Prediction DOWN' ..................... 223
10.2.4.31 Diagnostic value '49.WT00' ... '56.WT95' - Number of operating hours in the travel
range WT00 to WT95............................................................................................................ 223
10.2.4.32 Diagnostic value '57.mA - Setpoint current' .......................................................................... 224
10.3 Online diagnostics ................................................................................................................. 224
10.3.1 Overview of online diagnostics ............................................................................................. 224
10.3.2 Overview of error codes ........................................................................................................ 226
10.3.3 XDIAG parameter ................................................................................................................. 228
10.3.4 Meaning of error codes ......................................................................................................... 228
10.3.4.1 1 Remaining control deviation .............................................................................................. 228
10.3.4.2 2 Device not in "Automatic" mode ........................................................................................ 228
10.3.4.3 3 Binary input BIN1 or BIN2 active ....................................................................................... 228
10.3.4.4 4 Monitoring the number of total strokes .............................................................................. 229
10.3.4.5 5 Monitoring the number of changes in direction .................................................................. 229
10.3.4.6 6 Monitoring the lower endstop / 7 Monitoring the upper endstop ....................................... 229
10.3.4.7 8 Monitoring deadband ......................................................................................................... 229
10.3.4.8 9 Partial stroke test ............................................................................................................... 230
10.3.4.9 10 Monitoring of dynamic control valve behavior ................................................................. 230
10.3.4.10 11 Monitoring the pneumatic leakage ................................................................................... 230
10.3.4.11 12 Monitoring of stiction (slipstick) ........................................................................................ 230
10.3.4.12 13 Monitoring the lower limit temperature............................................................................. 230
10.3.4.13 14 Monitoring the upper limit temperature ............................................................................ 230
10.3.4.14 15 Monitoring the position average value ............................................................................. 230
10.3.4.15 16 Monitoring the plausibility of values for the partial stroke test ......................................... 231
SIPART PS2 with and without HART
Operating Instructions, 02/2016, A5E00074631-AB
Table of contents
9