Korg PA1X User Manual page 378

374 Effects
Mono – Mono Chain
083: Wah - Amp Sim
(Wah/Auto Wah – Amp Simulation)
This effect combines a mono-type wah and an amp simulation.
You can change the order of the effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Wah/Auto Wah
+
Wah
Right
Sweep Mode
Envelope
Auto
D-mod
D -mod
LFO
LFO
[W] Frequency Bottom
Sets the lower limit of the wah center frequency
a
Frequency Top
Sets the upper limit of the wah center frequency
[W] Sweep Mode
Selects the control from auto-wah, modulation source, and LFO
b
Src
Selects the modulation source for the wah when Sweep Mode=D-mod
[W] LFO Frequency [Hz]
c
Sets the LFO speed
[W] Resonance
Sets the resonance amount
d
Low Pass Filter
Switches the wah low pass filter on and off
[A] Amplifier Type
e Selects the type of guitar amplifier
Routing
f
Switches the order of the wah and amp simulation connection
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
g
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
Wet / Dry
Routing
Amp Simulation
Amp Simulation Filter
Wet / Dry
0...100
☞
Fx:009
0...100
☞
Fx:009
Auto, D-mod, LFO
☞
Fx:009,
Off...Tempo
0.02...20.00Hz
0...100
Off, On
Solid State, British
(EL84), American
(6L6)
WAH → AMP, AMP → WAH
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
084: Decimator - Amp
(Decimator – Amp Simulation)
This effect combines a mono-type decimator and an amp simu-
lation. You can change the order of the effect connection.
[D] Pre LPFOff, On
Turn the harmonic noise caused by lowered sampling on and off
a
High Damp [%]
Sets the ratio of high-range damping
[D] Sampling Freq [Hz] (Sampling Frequency)
Sets the sampling frequency
b
Resolution
Sets the data bit length
[D] Output Level
c
Sets the decimator output level
[A] Amplifier Type
d Selects the type of guitar amplifier
RoutingDECI→AMP, AMP→DECI
e
Switches the order of the wah and amp simulation connection
Wet/DryDry, 1:99...99:1, Wet
Table , "Sets the balance between the effect and dry sounds," on
page 330
SrcOff...Tempo
f Table , "Selects the modulation source of the effect balance," on
page 330
Amt
Table , "Sets the modulation amount of the
effect balance," on page 330
085: Decimator - Comp
(Decimator – Compressor)
This effect combines a mono-type decimator and a compressor.
You can change the order of the effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Decimator
Resolution Output Level
+
Decimator
Pre LPF
High Damp
Right
[D] Pre LPF
Turn the harmonic noise caused by lowered sampling on and off
a
High Damp [%]
Sets the ratio of high-range damping
[D] Sampling Freq [Hz] (Sampling Frequency)
Sets the sampling frequency
b
Resolution
Sets the data bit length
[D] Output Level
c
Sets the decimator output level
[C] Sensitivity
d
Sets the sensitivity
[C] Attack
Table , "Sets the attack level," on page 330
e
Output Level
Sets the compressor output level
Routing
f
Switches the order of the decimator and compressor connection
☞
Fx:014
0...100%
1.00k...48.00kH
z
4...24
☞
Fx:014
0...100
☞
Fx:014
Solid State, Brit-
ish (EL84),
American (6L6)
–100...+100
Wet / Dry
Routing
Compressor
Comp
Output Level
Wet / Dry
Envelope - Control
Off, On
☞
Fx:014
0...100%
1.00k...48.00kHz
4...24
☞
Fx:014
0...100
☞
Fx:014
1...100
☞
Fx:002
1...100
☞
Fx:002
0...100
☞
Fx:002
DECI→CMP, CMP→DECI