Korg PA1X User Manual page 352

348 Effects
Pitch/Phase Mod.
The effect is off when a value for the modulation source speci-
fied for the "Src" parameter is smaller than 64, and the effect is
on when the value is 64 or higher. The Doppler effect is trig-
gered when the value changes from 63 or smaller to 64 or
higher.
e: Pitch Depth
With the Doppler effect, the pitch is raised when the sound
approaches, and the pitch is lowered when the sound goes away.
This parameter sets this pitch variation.
f: Pan Depth
This parameter sets the width of the stereo image of the effect
sound. With larger values, the sound seems to come and go from
much further away. With positive values, the sound moves from
left to right; with negative values, the sound moves from right to
left.
Pitch
Pan Depth
= (+) value
Original Pitch
Left
< < < < < <<<<<< >>>>>> > >
Louder
031: Scratch
This effect is applied by recording the input signal and moving
the modulation source. It simulates the sound of scratches you
can make using a turntable.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Rec Control
Right
D-mod
D -mod
Envelope Control
Input
Envelope Select
D
Scratch Source
a
Selects the modulation source for simulation control
Response
b
Sets the speed of the response to the Scratch Source
Envelope Select
Selects whether the start and end of recording is controlled via the modula-
tion source or the input signal level
c
Src
Selects the modulation source that controls recording when Envelope Select
is set to D-mod
Threshold
d Sets the recording start level when Envelope Select is set to Input
Response
e
Sets the speed of the response to the end of recording
Direct Mix
f
Selects how a dry sound is mixed
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
g
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
Doppler - Pitch / Pan Depth
Pan Depth
= (–) value
Pitch Depth
Center
Right
Pan Depth
> > >
Volume Louder
Wet / Dry
Direct
Scratch
Mix
Scratch
Wet / Dry
-mod
Off...Tempo
☞
,
0...100
☞
D-mod, Input
☞
,
Off...Tempo
☞
0...100
☞
0...100
☞
Always On, Always Off, Cross Fade
☞
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
a: Scratch Source, b: Response
The Scratch Source parameter enables you to select the modula-
tion source that controls simulation. The value of the modulation
source corresponds to the playback position. The Response
parameter enables you to set the speed of the response to the
modulation source.
Start Playback Position
Recorded Sound
Scratch Source
JS X
D -mod
Ribbon – Max
JS+Y
JS–Y
Zero
etc...
c: Envelope Select, c: Src, d: Threshold
When "Envelope Select" is set to D-mod, the input signal will be
recorded only when the modulation source value is 64 or higher.
When "Envelope Select" is set to Input, the input signal will be
recorded only when its level is over the Threshold value.
The maximum recording time is 1365msec. If this is exceeded, the
recorded data will start being erased from the top.
e: Response
This parameter enables you to set the speed of the response to
the end of recording. Set a smaller value when you are recording
a phrase or rhythm pattern, and set a higher value if you are
recording only one note.
f: Direct Mix
With Always On, a dry sound is usually output. With Always Off,
dry sounds are not output. With Cross Fade, a dry sound is usually
output, and it is muted only when scratching.
Set Wet/Dry to Wet to use this parameter effectively.
Scratch Source
End
Scratch!
+ Max
Zero
+ Max