Korg PA1X User Manual page 351

a: Control Mode, e: Voice1: Resonance, h: Voice2:
Resonance
This parameter determines the resonance intensity.
When "Control Mode" = Manual, the "Resonance" parameter
sets the intensity of resonance. If the "Resonance" parameter has
a negative value, harmonics will be changed, and resonance will
occur at a pitch one octave lower.
When "Control Mode" = LFO, the intensity of resonance varies
according to the LFO. The LFO sways between positive and nega-
tive values, causing resonance to occur between specified pitches
an octave apart in turn.
When "Control Mode" = D-mod, the resonance is controlled by
the dynamic modulation source. If JS X is assigned as the modula-
tion source, the pitch an octave higher and lower can be con-
trolled, similar to when LFO is selected for Control Mode.
a: LFO/D-mod Invert
When "Control Mode" = LFO or D-mod, the controlled phase of
either Voice 1 or 2 will be reversed. When the resonance pitch is
set for Voice 1 (Resonance has a positive value), Voice 2 will reso-
nate at a pitch an octave below (Resonance has a negative value).
d: Voice1: Pitch, d: Fine [cent], g: Voice2: Pitch, g: Fine
[cent]
The Pitch parameter specifies the pitch of resonance by note
name. The "Fine" parameter allows for fine adjustment in steps
of cents.
e: High Damp [%], h: High Damp [%]
This parameter sets the damping amount of resonant sound in
the high range. Lower values will make a metallic sound with a
higher range of harmonics.
030: Doppler
This effect simulates the "Doppler effect" of a moving sound
with a changing pitch, similar to the siren of an passing ambu-
lance. Mixing the effect sound with the dry sound will create a
unique chorus effect.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Doppler
Right
LFO
D -mod
LFO Mode = 1-Shot
Trigger
LFO Mode
Switches LFO operation mode
a
Src
When LFO Mode is set to 1-Shot, this modulation source triggers the LFO
☞
LFO Sync
b
Switches between LFO reset on and off when LFO Mode is set to Loop
LFO Frequency [Hz]
Sets the LFO speed
Src
c
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
d
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
Pitch Depth
Sets the pitch variation of the moving sound
Src
e
Selects the modulation source of pitch variation
Amt
Sets the modulation amount of pitch variation
Pan Depth
Sets the panning of the moving sound
Src
f
Selects the modulation source of panning
Amt
Sets the modulation amount of panning
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
g
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
a: LFO Mode, a: Src, b: LFO Sync
The "LFO Mode" parameter switches LFO operation mode. When
Loop is selected, the Doppler effect will be created repeatedly. If
"LFO Sync" is set to On, the LFO will be reset when the modula-
tion source specified with the "Src" parameter is turned on.
When "LFO Mode" is set to 1-Shot, the Doppler effect is created
only once when the modulation source specified in the "Src" field
is turned on. At this time if you do not set the "Src" parameter,
the Doppler effect will not be created, and no effect sound will
be output.
Effects 347
Pitch/Phase Mod.
Wet / Dry
Pan Depth
Wet / Dry
Loop, 1-Shot
☞
,
Off...Tempo
Off, On
☞
0.02...20.00Hz
☞
Fx:009,
Off...Tempo
–20.00...+20.00Hz
Off, On
☞
Fx:009,
MIDI, 40...240
☞
Fx:009
☞
Fx:009
x1...x16
☞
Fx:009
0...100
☞
,
Off...Tempo
–100...+100
–100...+100
☞
,
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100