Korg PA1X User Manual page 356

352 Effects
Mod./P.Shift
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
h
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
a: Pre LPF
This parameter enables you to set the damping amount of the
high range sound input to the ring modulator. If the input sound
contains lots of harmonics, the effect may sound dirty. In this
case, cut a certain amount of high range.
b: OSC Mode
This parameter determines whether or not the oscillator fre-
quency follows the note number.
c: Fixed Frequency [Hz]
This parameter sets the oscillator frequency when "OSC Mode" is
set to Fixed.
d: Note Offset, d: Note Fine
These parameters for the oscillator are used when "OSC Mode" is
set to Note (Key Follow). The "Note Offset" sets the pitch differ-
ence from the original note in semitone steps. The "Note Fine"
parameter fine-adjusts the pitch in cent steps. Matching the oscil-
lator frequency with the note number produces a ring modula-
tion effect in the correct key.
037: Detune
Using this effect, you can obtain a detune effect that offsets the
pitch of the effect sound slightly from the pitch of the input sig-
nal. Compared to the chorus effect, a more natural sound thick-
ness will be created.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Input Level
+
Detune
Input Level
Right
Pitch Shift [cent]
Sets the pitch difference from the input signal
Src
a
Selects the modulation source of the pitch shift
Amt
Sets the modulation amount of the pitch shift
Delay Time [msec]
b
Sets the delay time
Feedback
Sets the feedback amount
c
High Damp [%]
Sets the damping amount in the high range
Input Level Dmod [%]
Sets the modulation amount of the input level
d
Src
Selects the modulation source for the input level
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
e
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Wet / Dry
High Damp
Delay
Feedback
Wet / Dry
–100...+100cent
Off...Tempo
–100...+100cent
0...1000msec
–100...+100
0...100%
–100...+100
☞
,
Off...Tempo
☞
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
d: Input Level Dmod [%], d: Src
This parameter sets the dynamic modulation of the input level.
Input Level
x1.0 Amt= +50
Amt= +100
x0.5
D -mod
Higher
Zero Max
038: Pitch Shifter
This effect changes the pitch of the input signal. You can select
from three types: Fast (quick response), Medium, and Slow (pre-
serves tonal quality). You can also create an effect in which the
pitch is gradually raised (or dropped) using the delay with feed-
back.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Input Level
+
Pitch Shifter
Pre
Feedback Position
Input Level
Right
Mode
a
Switches Pitch Shifter mode
Pitch Shift [1/2tone]
Sets the pitch shift amount by steps of a semitone
Src
b
Selects the modulation source of pitch shift amount
Amt
Sets the modulation amount of pitch shift amount
Fine [cent]
Sets the pitch shift amount by steps of a cent
c
Amt
Sets the modulation amount of pitch shift amount
Delay Time [msec]
d
Sets the delay time
Feedback Position
e
Switches the feedback connection.
Feedback
Sets the feedback amount
f
High Damp [%]
Sets the damping amount in the high range
Input Level Dmod [%]
Sets the modulation amount of the input level
g
Src
Selects the modulation source for the input level
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 330
Src
h
Table , "Selects the modulation source of the effect balance," on page 330
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 330
a: Mode
This parameter switches the pitch shifter operating mode. With
Slow, tonal quality will not be changed too much. With Fast, the
effect becomes a Pitch Shifter that has a quick response, but may
change the tone. Medium is in between these two. If you do not
need to set too much pitch shift amount, set this parameter to
Slow. If you wish to change the pitch significantly, use Fast.
Input Level D-mod
Input Level
x1.0 Amt= –50
Amt= –100
x0.5
D -mod
Higher
Zero Max
Wet / Dry
High Damp
Delay
Post
Feedback
Wet / Dry
Slow, Medium, Fast
☞
–24...+24
☞
,
Off...Tempo
☞
–24...+24
–100...+100cent
☞
,
–100...+100cent
0...1000msec
Pre, Post
–100...+100
0...100%
–100...+100
☞
Fx:037,
Off...Tempo
☞
Fx:037
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
☞
☞
☞
☞