Adjusting The Speed Limiter; Replacing The Handle Mounted Light Bulb - Yamaha 2016 Grizzly yfm700gplg Service Manual

TIP
If the free play cannot be adjusted here, adjust it
at the handlebar side of the cable.
▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
Handlebar side
a. Slide back the rubber cover "1".
b. Loosen the locknut "2".
c. Turn the adjusting bolt "3" in direction "a" or
"b" until the correct free play is obtained.
Direction "a"
Free play is increased.
Direction "b"
Free play is decreased.
3
b
a
1
d. Tighten the locknut.
e. Slide the rubber cover to its original position.
EWB03810
WARNING
After adjusting the throttle cable free play,
start the engine and turn the handlebar to the
right and to the left to ensure that this does
not cause the engine idling speed to change.
▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
4. Install:
• Storage compartment
Refer to "GENERAL CHASSIS (5)" on page
4-17.
EBS30463

ADJUSTING THE SPEED LIMITER

The speed limiter keeps the throttle from becom-
ing fully-opened even when the throttle lever is
applied to the maximum position. Screwing in
the adjusting screw stops the engine speed from
increasing.
1. Measure:
• Speed limiter length
Out of specification → Adjust.
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
2
2WD
4WD
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
PERIODIC MAINTENANCE
2. Adjust:
▲▲▲
• Speed limiter length "a"
▼▼▼
▼ ▼▼▼ ▼ ▼▼▼ ▼
a. Loosen the locknut "1".
b. Turn the adjuster "2" in direction "b" or "c" until
the specified speed limiter length is obtained.
Direction "b"
Speed limiter length is decreased.
Direction "c"
Speed limiter length is increased.
c. Tighten the locknut.
EWB03830
WARNING
• Particularly for a beginner rider, the speed
limiter should be screwed in completely.
Screw it out little by little as their riding
technique improves. Never remove the
speed limiter for a beginning rider.
• For proper throttle lever operation, do not
turn out the adjuster more than the speci-
fied length. Also, always adjust the throttle
▲▲▲
cable free play to within specification.
▲ ▲▲▲ ▲ ▲▲▲ ▲
EBS30593
REPLACING THE HANDLE MOUNTED LIGHT
BULB
1. Remove:
• Quick fastener "1"
• Handle mounted light cover "2"
3-34
Speed limiter length
12 mm (0.5 in)
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a
1
c
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
▼ ▼▼▼ ▼ ▼▼▼
2
b
▲ ▲▲▲ ▲ ▲▲▲