Xerox Phaser 4620 Service Manual page 354

Table 2 NVM Chain 8
Location NVM Name NVM Description
08-140 Tray 3 Pick Roller Number of Tray 3 sheets since
life page counter last reset. Read only.
08-150 Tray 4 Pick Roller Number of Tray 4 sheets since
life page counter last reset. Read only.
08-160 Tray 5 Pick Roller Number of Tray 5 sheets since
life page counter last reset. Read only.
08-170 Tray 6 Pick Roller Number of Tray 6 sheets since
life page counter last reset. Read only.
Table 3 NVM Chain 9
Location NVM Name NVM Description
09-100 LD Light Level 600dpi laser light level. Value
in PWM.
09-110 MHV Control Main charge bias control.
Bias Control Basic of value (HVPS setting
is value). Value in PWM.
09-120 THV Control Bias Transfer bias control. Basic
Control of value (HVPS setting is
value). Value in PWM.
09-130 Deve Bias Con- Developer bias control. Basic
trol of value (HVPS setting is
value). Value in PWM standard
voltage: -500V (PWM 522).
09-140 Detack Bias Con- Detack bias control. Basic of
trol value (HVPS setting is
value). Value in PWM standard
voltage: -1800V
09-150 Altitude Adjust- Altitude adjustment in
ment meters.
09-200 Drum Life Page Drum life count since last reset.
Counter Read only.
09-210 Toner Cartridge Toner Cartridge life count since
Life Page Count last reset. Read only.
09-220 Drum life Time Drum rotation time in minutes.
Read only.
09-230 Transfer Roller Transfer Roller life count since
Life Page Count last reset. Read only.
09-300 Dot Count Dot count value of consecutive
printing. Read only.
Table 4 NVM Chain 10
Location NVM Name NVM Description
10-100 StandBy Temper- Target temperature during
ature Offset standby mode.
General Procedures/Information
dC131
Value Default Location NVM Name
Current count None 10-105
Current count None 10-115
Current count None
10-120
Current count None
10-125
10-130
Value Default
200 ~ 600 350
10-135
108 ~145 126
10-140
41 ~ 220 76
10-145
10-150
408 ~ 607 522
10-155
10-200
80 ~ 160 123
10-210
10-220
Current setting None
Current count. None
10-300
Current count None
10-310
Current count None
Current count None
One page dot count.
Value Default
0 ~ 15 (4 steps / 5 10
degree intervals)
5/2011
6-28
Table 4 NVM Chain 10
NVM Description
Run Tempera- Target temperature during
ture Offset run mode.
101-185 mm Offset temperature required on
Temperature Off- thermistor B for paper width.
set
186-216 mm Offset temperature required on
Temperature Off- thermistor B for paper width.
set
60gms Tempera- Media weight offset for heat roll
ture Offset temperature.
90gms Tempera- Media weight offset for heat roll
ture Offset temperature.
Bond Tempera- Media weight offset for heat roll
ture Offset temperature.
Transparency Media type offset for heat roll
Temperature Off- temperature.
set
Cardstock Tem- Media weight offset for heat roll
perature Offset temperature.
Envelope Tem- Media type offset for heat roll
perature Offset temperature.
label Tempera- Media type offset for heat roll
ture Offset temperature.
Fuser Life Page Fuser life count since last reset.
Counter Read only.
Heat Roller Life Heat Roller life count since last
Page Counter reset. Read only.
Pressure Roller Pressure Roller life count since
Life Page last reset. Read only.
Counter
Pick-up Interval Change the time interval for
Delay paper pick-up.
Pick-up Interval Change the time interval for
Delay (Special) special media pick-up.
Phaser 4600/4620 Printer Service Manual
Value Default
0 ~ 15 (3 steps / 5 5
degree intervals)
0 ~ 15 (4 steps / 5 5
degree intervals)
0 ~ 15 (4 steps / 5 5
degree intervals)
0 ~ 15 (4 steps / 5 5
degree intervals)
0 ~ 10 (3 steps / 5 5
degree intervals)
0 ~ 10 (3 steps / 5 5
degree intervals)
0 ~ 10 (3 steps / 5 5
degree intervals)
0 ~ 10 (3 steps / 5 5
degree intervals)
0 ~ 10 (3 steps / 5 5
degree intervals)
0 ~ 10 (3 steps / 5 5
degree intervals)
Current count None
Current count None
Current count None
0 ~ 100 (* 100 msec ) 0
0 ~ 100 (* 100 msec ) 0
Revision - Xerox Internal Use Only