How To Recharge The Battery; Getting The Most From Your Lithium Polymer Battery - Hirobo S.R.B. Quark User Manual

to recharge the baltery
Follow the steps 1 to 4 illusiraied in the figure below and turn on the switch.
Please read the instruclion manual while the batiery is charging.
3. Botate lhe proleclive.ap
The side wth lhe sickershou d lace up
When recharqinE is complele, imm€diately remove the balteiy from the
charger and thepower plog from rhe Power outlet.
lf they are left connected, it may cause damage to the battery
and/or the charger.
lf the connector remains connected after using the rnodel or charging the
battery, it may result in damage, a fire, over-discharge, overcharge, or lhe
model going out of conirol due lo forgetting to lurn ofi the swilch.
For safe storage, disconnect the connector aiter using the model or charging
ihe battery.
Also prevenl the battery from getting wet, and prevent the connector and
cord from contacling any metalwhen sioring ihe battery.
Be sure to close lhe prolecl ve
cap when you have f n shed
Gelting the most from your lithium polymer battery
lOAs il is not poss'ble to Lse a lithiu'n polvrpr bahe y
'ii has been ovel
-
discharged. t ic i.nportant to pay altent o to lhe lolow:no to dvoid ovpr
discharging your baltery.
.lf during flying it is not possible to achieve lift even when
under full throttle, stop the flight and recharge the battery.
. Do not discharge using a discharger etc before recharging' (lt
is possible to recharge lithium polymer batteries when they
are not fully discharged without any loss oI pedormance )
.Even i( your battery has been recharged, it will naturally
discharge gradually over time. To prepare lor storage,
recharge the battery before stodng it. lt may be necessary to
occasionally recharge the battery when it is not being used for
a long time to prevent it from completely discharging.
Oln a cold envirormenl. lhe oatterv wil rol pedo'n ds wel lLe lenglh of
time the batlery can be used will be shorier and there may be inslances
where adeouaie output cannol be achieved. For ihese reasons, use ihis
produci in a warm environment.
lf the length of time ihe battery can be used becomes significantly
shorler, it is an indjcation that the bailery has deteriorated and you need
to purchase a new battery.
2. P rs the cod inlo
Liqhts red Fecharginq
OLghts green: Recharging is comp el€
aFlashes red: Efror
'Ford€rals ofthe LED display rerer to the
charg€r nsturlioi nanual.
Oll an error occurs, please leave
the battery connected to ihe
charger for about 10 minutes.
Next, remove the lithium
polymer
bailery
from the
charger, and then re-insert it
into the charger to begin the
recharging process again.
lf you are unable to recharge
the battery even
after
reinserting it several times, it
is likely that the battery has
either degraded or been over-
discharged, in which case you
will need to purchase a new
battery.
Be careJul to avoid electrical shorts.
Be carefu to ensurethatmela obleclsdo noi
come in10 d recl conladwilh the lermina s
olicky place lrre protective cap when you
have Iinished recharoing
The connector used for the
S.R.B Series has a ditferent
shape in order to prevent it Jrom
being wrongly connected lo
other RC devces, etc.
Be sure to use only Hlrobo's
genuine conneclor. Never use a
subslituie.
A so, never atlernpt to extend or
rnodify the connector.
IPointl
OAfier flying your helicopler, be
sure to charge the battery
before you leave il in storage,
a)ll, during a flight, the battery
charge begins to run low, a
fail-safe function will engage
and the motor will slow to a
stop. lt this occurs, Please be
sure to recharge the baltery
as soon as Possible.
Each t me lre ba[ery s chaqed
and dischaqed rhe enqrh or lne
ir dai be used win get shoiGl
+Number oi charSe and d scharge
6