Download Print this page
Hirobo 0412-903 Quick Start Manual

Hirobo 0412-903 Quick Start Manual

30 scale fuselage

Advertisement

Quick Links

30スケールボディ
30 scale fuselage
LONG RANGER
この度は30スケールボディ LONG RANGER をお買い上げ頂き誠に 
ありがとうございます。取扱説明書に従い、組立を行って下さい。
注意 
・ボディに搭載する前に機体のみでフライト調整して下さい。そ
の際、垂直尾翼を取り付けてフライトして下さい。垂直尾翼が
ないとテールがハンチング(左右に振れる現象)します。
・このボディは競技用ではありません。高回転(1800rpm以上)
での無理なフライトは危険ですので行わないで下さい。
・機体に振動がある場合。ボディに搭載しても充分なフライト性
能が発揮できない上、破損や墜落の原因になる可能性がありま
す。搭載前に充分なメンテナンスを行って下さい。
このキットはボディのみです。
別売品 
搭載可能機種
シャトルプラス 
シャトルプラス+2
シャトルZXX
シャトルSXX
164mm
228mm
マフラー許容サイズ 
70mm以下
20mm以下
ø45mm以下
65mm以下
純正適合マフラー
JI-50マフラーセット
0402-050 ○2,100 (2,000)
0412-903 青 (BLUE)
0412-904 赤 (RED)
1110mm
Scale: 1/9
Shuttle Plus用
For Shuttle Plus
Thank you for purchasing the 30 scale fuselage LONG RANGER.
Read these instructions carefully for the proper assembly.
Caution
・Before mounting the
chassis to the
the
chassis
only. In this regard, install the vertical fin to the
chassis.
A maneuver without the vertical fin will cause tail hunting.
・This aircraft is not designed for flight competitions.
dangerous to maneuver this aircraft at high speeds (1800 rpm
or higher).
Never fly this aircraft at excessive speeds.
・When there is vibration in the chassis: Not only will this model's
full flight characteristics be degraded, even if mounted on the
fuselage, it is also possible to cause damage or crashes.
Perform thorough maintenance in advance of mounting.
This kit includes only the fuselage unit.
Sold separately
Model's that can be mounted
Shuttle Plus
Shuttle Plus+2
Shuttle ZXX
Shuttle SXX
1
220mm
ボディ重量:約600g
Body weight: approx. 600g
fuselage, adjust the flight of
Muffler Tolerance Size
Max. ø45 mm
Max. 70 mm Max. 20 mm
Max. 65 mm
Genuine muffler
JI-50 muffler set
0402-050 ○2,100 (2,000)
275mm
It is

Advertisement

loading

Summary of Contents for Hirobo 0412-903

  • Page 1 30スケールボディ 0412-903 青 (BLUE) 30 scale fuselage 0412-904 赤 (RED) 275mm 220mm 164mm 1110mm 228mm ボディ重量:約600g Body weight: approx. 600g LONG RANGER Scale: 1/9 Shuttle Plus用 For Shuttle Plus この度は30スケールボディ LONG RANGER をお買い上げ頂き誠に  Thank you for purchasing the 30 scale fuselage LONG RANGER.
  • Page 2 〈組立をはじめる前に〉 〈Before Assembling〉 組立に必要なもの (別売) Required Tools (sold separately) ¥税込価格(税抜価格) ¥ Price including Tax (Price excluding Tax) +ドライバー ラジオペンチ ニッパー カッターナイフ 定規 ハサミ 大・小 Long-nose pliers Nipper Cutter knife Ruler Scissors Large and small Phillips screwdrivers 2513-045 ¥840 (800) (曲面/Curve) 2513-046 ¥630 (600) (ミ...
  • Page 3 機体搭載の準備  Preparing to mount the chassis シャトルプラス・シャトルZXX・シャトルSXXの場合 Shuttle Plus, Shuttle ZXX and Shuttle SXX 注意 Caution テールユニットケースを外します。 Remove the tail unit case. ボディに搭載する前に機体のみでフライト調整して下さい。 Before mounting the chassis to the fuselage, carry out a flight adjustment with just the chassis. ローターヘッド部をメインマストより外します。 Remove the rotor head together with the main mast.
  • Page 4 シャトルプラス+2の場合 Shuttle Plus+2 注意 Caution テールユニットケースを外します。 Remove the tail unit case. ボディに搭載する前に機体のみでフライト調整して下さい。 Before mounting the chassis to the fuselage, carry out a flight adjustment with just the chassis. ローターヘッド部をメインマストより外します。 Remove the rotor head together with the main mast. メインギヤ 使用しません Main gear Not used マフラー...
  • Page 5 ボディの加工  Preparing the fuselage 機体をボディに入れ、フレームを仮組みし、メインマスト位置、  Place the chassis in the fuselage, temporarily assemble the frames, determine 機体取付位置を決め、ボディを加工します。 the main mast position and the chassis mounting position, and then prepare the fuselage. ポイント Point FRPボディの加工にはヤスリ・リューター等を使用し、 慎重に行います。 ボディを加工した後は、カット面に瞬間接着剤を塗 ってください。 Carefully prepare the FRP fuselage using a file and router, etc.
  • Page 6 テール部分の加工  Preparing the tail シャトルプラス・シャトルZXX・シャトルSXXの場合 Shuttle Plus, Shuttle ZXX and Shuttle SXX テール部分の加工は特にありませんが、機体を搭載した後テー There is no particular preparation needed for the tail unit. If the tail unit or ルユニットやリンケージ可動部がボディに干渉する場合は、ヤ the moving part of the linkage touches the fuselage after mounting the スリ等でボディを削り、修正して下さい。...
  • Page 7 機体の搭載  Mount the chassis シャトルプラス+2の場合 Shuttle Plus+2 オプション Option シャトルプラスの場合 Shuttle Plus オプションの2513-064防音シートをボディの内側(フ ……………………… 4 M3X16TS レームの下など)に貼ると音が静かになります。 If the optional sound-insulating sheet (2513-064) is affixed to the inside of the fuselage (below the frame, etc), the noise is reduced. M3X10TS ………………………...
  • Page 8 ボディの組立  Assembling the fuselage ……………… 10 M3X6TS塗装済  M3X6TS (painted) ………… 4 M2.6X12皿TS塗装済  M2.6X12 countersunk TS (painted) テールコーン取付けネジM3X6TSが、テ カット ールユニットケースに干渉するようであ Cut off れば、ヤスリ等で削って下さい。 If the tail cone mounting screws (M3X6TS) touch the tail unit case, file them down. M3X6TS M3X6TS ø3の穴をあけます。  Open ø3 hole.
  • Page 9 パーツリスト  0412-283 Parts List 0412-284 0412-281 0412-282 0412-285 * The prices in parentheses are the prices excluding consumption tax. 税込価格 コード No. 品名 入数 備考 ( 税抜価格 ) 円 Code No. Part Q'ty Remarks Price (Yen) 1 式 10,500 ロングレンジャー 尾翼セット 青 受注生産...
  • Page 10 M E M O M E M O M E M O M E M O M E M O...
  • Page 11 M E M O M E M O M E M O M E M O M E M O...
  • Page 12 注意 Note   平成12年5月 初版発行 ①本書の内容の一部または全部を無断で転載することは禁止されています。 平成12年7月 第2版発行 ②本書の内容については、将来予告なしに変更することがあります。 平成12年12月 第3版発行 ③本書の内容について万全を期しておりますが、万一ご不審な点や誤り、記載もれなどお気付 平成18年1月  第4版発行   きのことがありましたら、ご一報くださいますようお願いいたします。 ④運用した結果については③項にかかわらず責任を負いかねますので、ご了承ください。 平成18年7月  第5版発行  ①Reproduction of this manual, or any part thereof, is strictly prohibited. First printing May 2000 ②The contents of this manual are subject to change without prior notice. Second printing July 2000 ③Every effort has been made to ensure that this manual is complete and correct.

This manual is also suitable for:

0412-904