Table of Contents
Advertisement
Variable Frame Rate-Recording
To record active frames from the output of a variable frame-
rate camera, set setup menu No. 040 (VFR REC) to ON. This
enables instant viewing of slow-motion and fast-motion speed
effects during shooting.
◆ NOTE:
• Audio and external time codes cannot be recorded in this mode.
Recording HD SDI Signals Output by an HD Camera as 1080/23.98p
The unit is capable of AVC-Intra 1080/23.98p native recording
of HD SDI (1080/23.98p over 59.94i) output from an HD camera.
Recording HD SDI signals from camera
output
1
Connect the HD SDI (1080/23.98p over 59.94i) output
from an HD camera recorder to the SDI IN connector
and press the INPUT SELECT button to select HD SDI.
SDI IN connector
VIDEO
REF VIDEO IN TIME CODE AUDIO MON
IN
SDI
75
IN
AUTO
OUT
OUT
DVCPRO/DV
1
POWER
ON
OFF
METER
FULL/FINE
MONITOR
SELECT
METER SELECT
CH 1-4 CH 5-8
INPUT SELECT
VIDEO AUDIO
CH 1
CH 2
CH 3
REC
VAR
UNITY
THUMBNAIL
PLAYLIST
VIDEO
EDIT MODE
SET
LAST X
MULTI
DELETE
SEL
EXIT
MENU
CANCEL/PF
DIAG
SLOT CLIP
OPERATION
PF1
44
Introduction: Recording From a Variable Frame-Rate Camera
HD SDI (1080/23.98p over 59.94i)
output
AES/EBU
IN
L
IN
IN
R
E
M
CH1·2
CH3·4
O
T
E
R
OUT
OUT
OUT
3
PREVIEW
STOP
REC
A.LEVEL REC
PLAYER
STILL/
SOURCE SELECT
PLAY
PAUSE
REW
COUNTER
RESET
REVIEW
PREV
1 CLIP PLAY
NEW
TC PRESET
PROP
CH 4
TEXT
INT
TCG
MEMO
REGEN
PRESET
EXT
MARKER
A1
A2
GO TO
A3
A4
A.DUB
MODE
TRIM
SLOT SELECT
IN
ENTRY
OUT
ALL CLIP
CLIP LIST
SHIFT
PF2
PF3
PF4
• The P2 card that is being recorded cannot be changed during
recording.
• In this mode, the remaining P2 card capacity at 60p (50p), the
slowest slow-speed effect, is indicated.
• When 59-23 or 60-24 is set in setup menu No. 25 (SYSTEM FREQ),
movement in HD SDI video output may look unnatural when the
input frame rate is something other than 24p.
• Changing the frame rate while recording a video signal from a variable
frame rate camera may result in frame loss in the changeover phase.
2
Make the following setup menu settings.
Item
No.25
No.020
3
Hold down the REC button and the STILL/PAUSE
button simultaneously to set the unit to REC PAUSE
mode.
4
To start recording, press the STILL/PAUSE button
while viewing the video output from the camera HD
SDI output.
◆ NOTE:
• Setup menu No. 155 (AUTO REC) to TYPE2 and set the CONTROL
switch to REMOTE. The unit will then automatically start and stop
recording as the REC and STOP buttons are pressed on the
camera.
• SDI is output in the 1080/23.98 PsF video format. IEEE1394 is not
output.
• No time code can be input to the TIME CODE IN connector.
• The SDI output is delayed relative to LCD monitor and monitor video
output. Analog audio, speaker and headphone output is
synchronized to the LCD monitor and monitor video output. To
synchronize these outputs to SDI output, set setup menu No. 778
(AUD OUT DLY) to ON.
4
• Set camera TCG to FREE RUN. A TC/UB of an SDI input that cannot
be properly read cannot be normally recorded.
FF
NEXT
Setting
SYSTEM FREQ
59-23
SYS FORMAT
1080p
Advertisement
Table of Contents
