Registering Events By Clip; Trimming Events; Revising Registered Events - Panasonic AJ-HPM200P Operation Instruction Manual

2
The event is recorded and appears on the timeline.
◆ NOTE:
• For a live recording of 1 second or less, the event is recorded
for 1 second, and only the IN and OUT point section is set as an
event on the timeline. The light of the REC button or other
indication operates within this IN/OUT point section only.
• Track selection is possible, but the input data are always output
(FULL EE).
• An external device (RS-422A) or external input (live recording)
cannot be used as a player under the following conditions:
- When setup menu No.25 (SYSTEM FREQ) is set to 59-23, 60-
24, or 60-25
- When the playlist format is 30PN, 24PN, or 25PN

Registering Events by Clip

Use the following procedure to add selected clips to the
playlist. This operation registers the start of a clip as the IN
point and its end as the OUT point.
OFF
METER
FULL/FINE
MONITOR
SELECT
METER SELECT
CH 1-4 CH 5-8
INPUT SELECT
VIDEO AUDIO
CH 1 CH 2 CH 3 CH 4
REC
VAR
UNITY
2
THUMBNAIL PLAYLIST VIDEO A1
3,6
EDIT MODE A3
SET LAST X
3,5
MULTI DELETE SLOT SELECT
SEL ENTRY
IN
EXIT MENU
CANCEL/PF DIAG
SLOT CLIP
CLIP LIST
OPERATION
PF1
4
1
Switch to player operation.
Press the PLAYER button to switch to player operation.
2
Display player thumbnails.
During player operation, press the THUMBNAIL button to
display thumbnails on the player screen.
3
Use the cursor buttons to select the clip you want to
add to the event and press the SET button.
The frame of the clip turns blue.
◆ NOTE:
• To divide the video of an event using text memos during event
registration, choose [SETTING] - [DIVIDED APPEND] and select
[ON].
➝ Refer to "Dividing the video of the event using text memos"
(page 93).
1
PREVIEW
STOP REC A.LEVEL REC
PLAYER
STILL/
SOURCE SELECT
PLAY PAUSE REW FF
COUNTER
RESET
REVIEW PREV NEXT
1 CLIP PLAY
NEW
TC PRESET
PROP
TEXT
INT
TCG
MEMO
REGEN
PRESET
EXT
MARKER
A2 GO TO
A4 A.DUB
MODE
TRIM
OUT
ALL CLIP
SHIFT
PF2 PF3
PF4
• Registration is not possible if the number of events will exceed
100 after they are divided. In such a case, choose [SETTING] -
[DIVIDED APPEND] and select [OFF].
4
Press the MENU button.
5
Use the cursor buttons to choose [OPERATION] -
[APPEND SELECTED CLIPS].
6
Press the SET button.
An event is registered with the start of a selected clip as
the IN point and its end as the OUT point.
◆ NOTE:
• Clips not in the playlist format are indicated by red numbers and
cannot be registered.
• This operation inserts a clip right before the event at the cursor
location. It is not possible to add the clip at any other location or
through overwriting.
• It is possible to use CLIP ➝ LIST (SHIFT + ENTRY) button
instead of operation described in step 5 to add a clip as an
event.
• The clip cannot be added when its addition causes the number
of events in a track to exceed 100.
• You can also add multiple clips. The clips are added in the order
they are selected.

Revising Registered Events

Events registered on the timeline can be revised.

Trimming events

You can change IN and OUT points for events in frame
increments (in 4-frame increments at 24PN). The result of
trimming will depend on whether insert or overwrite editing is
selected.
Operation Insert editing
Trim Subsequent events are
(extend) moved backwards by
an amount that
corresponds to the
extension.
Trim Subsequent events are
(contract) moved forward by an
amount that
corresponds to the
contraction.
Overwrite editing
Previous or
subsequent events will
be overwritten by an
amount corresponding
to the extension.
Previous and
subsequent events are
extended by an
amount corresponding
to the contraction.
101
Editing: Creating Playlists