Panasonic AJ-HPM200P Operation Instruction Manual page 170

Item
FR SUPER
No. DISP.
25 SYSTEM FREQ
26 HD SYS H ADV
27 VDCP CMD
28 VDCP ID
30 MENU LOCK
170
Setup: Item Settings
Setting
FR SUPER
No. DISP.
For AJ-HPM200P Sets system frequency.
0: 59.94 Hz
0000 59.94
1: 50 Hz
0001 50
2: 23.98 Hz
0002 23.98
3: 24 Hz
0003 24
4: 29.97 Hz
0004 29.97
5: 59-23 Hz
0005 59-23
Receives 59.94 Hz input. Select this frequency to record 2:3 pull-down converted
0006 60-24
(24-frame signal) output from VariCam: AJ-HDC27 series camera, AJ-HPX2700 or
0007 25
other camera.
0008 60-25
6: 60-24 Hz
For AJ-HPM200E
Receives 60Hz input. Select this frequency to record 2:3 pull-down converted
0000 59.94
(24-frame signal) output from VariCam: AJ-HDC27 series and AJ-HPX2700 series
0001 50
camera.
0002 23.98
7: 25 Hz
0003 24
8: 60-25 Hz
0004 29.97
Receives 60 Hz input. Select this frequency to record a variable frame rate set to 25p
0005 59-23
from VariCam: AJ-HDC27 series camera.
0006 60-24
0007 25
0008 60-25
0000 0H
59.94Hz
0001 90H
Specifies whether or not HD SDI output should advance 90H phase relative to SD REF
input during SD REF input.
0: Outputs HD SDI at the same phase as SD REF.
1: HD SDI output is output at a phase that is 90H advanced relative to SD REF.
NOTE:
• The audio output and TC output are output in the same phase as HD SDI output.
• At 720p, the phase difference is 120H.
0000 OFF
59.94Hz
ON
0001
Determines whether the REMOTE connector should support the VDCP command.
0: Does not support the command
1: Supports the command
NOTE:
• When this setting is ON and REMOTE is also selected, the thumbnail screen cannot
be opened.
• When this setting is ON and REMOTE is also selected, recording is not available.
• When this setting is ON, external device control using the MODE button and PLAYER
button are disabled.
• When this setting is ON, the setup menu No. 050 (P.ON GUI) setting is disabled and
the thumbnail screen and playlist screen do not open when the power is turned on.
• When this setting is ON, SEARCH, FF and REW from an external device are ignored.
0000 PRGNME
59.94Hz
0001 CLIPID
Selects metadata that can be used as an VDCP ID.
0002 USRNME
0: Selects PROGRAM NAME.
0003 SCNENO
1: Selects GLOBAL CLIP ID.
0004 CLPNME
2: Selects USER CLIP NAME.
3: Selects SCENE NO.
4: Selects CLIP NAME.
NOTE:
• Variable-length IDs up to 64 bytes are supported. Other IDs are ignored.
• To enable changes of this setting, the unit must be restarted by turning the power on
and off.
0000 OFF Sets/releases the system file lock mode.
0: Releases the lock (file data can be changed)
0001 ON
1: Lock is engaged (file data cannot be changed)
Settings and brief function description
only
29.97Hz
only
50Hz
only
50Hz