Kubota RTV-X900 Operator's Manual page 13

4. Do not stop or start suddenly when going uphill or
downhill. Be especially cautious when changing
direction on slopes.
5. If vehicle stops or loses power going up a hill, lock
parking brake to hold vehicle on slope. Maintain
direction of travel and release brake slowly. Back
straight downhill while maintaining control. Do not turn
vehicle sideways. Vehicle is more stable in a straight
forward or rearward position.
6. When riding on soft terrain, turn front wheels slightly
uphill to keep vehicle on a straight line across the hill.
7. If the vehicle begins to tip, turn front wheels downhill to
gain control before proceeding.
(1) To avoid upsets, always back up steep slopes. If
you cannot back up the slope or if you feel uneasy
on it, do not operate on it. Stay off slopes too
steep for safe operation.
(2) Driving forward out of a ditch, mired condition or
up a steep slope increases the risk of a vehicle to
be upset backward. Always back out of these
situations. Extra caution is required with 4-wheel
drive mode because the increased traction can
give the operator false confidence in the vehicle's
ability to climb slopes.
(3) Keep all movement on slopes slow and gradual.
Do not make sudden changes in speed, direction
or apply brake and make sudden motions of the
steering wheel.
(4) Special attention should be made to the weight
and location of implements and loads as such will
affect the stability of the vehicle.
C Operation in inclement conditions
1. Only operate during daylight or with good artificial
light.
2. Operate vehicle in an open, unobstructed area.
3. Use helmet and/or protective gear as appropriate or
required for the operating conditions.
4. Reduce speed according to trail, terrain and visibility
conditions.
5. Never drive exceeding the limit of visibility. Slow down
near crest of hill until getting a clear view of the other
side.
6. Stay alert for holes, rocks and other hidden hazards in
the terrain.
7. Never cross any body of water where depth may be
unknown to the operator (Deep water is considered
anything in excess the bottom edge of the axle cap).
Choose a course within the waterway where both
banks have a gradual incline. Cross at a point known
to be safe.
C Driving the vehicle at high speeds
1. Check the front wheel engagement. The braking
characteristics are different between 2 and 4 wheel
drive. Be aware of the difference and use carefully.
2. Always slow the vehicle down before turning. Turning
at high speed may tip the vehicle over.
3. Turn the headlights on.
4. Drive at speeds that allow you to maintain control at all
times.
5. Do not apply the differential lock while traveling at high
speeds. The vehicle may run out of control.
6. Avoid sudden motions of the steering wheel as they
can lead to a dangerous loss of stability. The risk is
especially great when the vehicle is traveling at high
speeds.
C Other miscellaneous
1. Clean platform if dirty and remove any debris from
around foot controls.
2. Always keep both hands on the steering wheel.
3. Always keep arms and legs inside the operating
compartment.
4. Never operate the vehicle while standing.
5. Do not tow a cart with any riders on it.
6. Never attempt wheelies, jumps or other stunts.
3. HAULING LOADS IN THE CARGO BED
1. No riders in cargo bed or anywhere else.
2. Do not overload vehicle. Securely anchor all loads.
3. Be sure load is evenly distributed.
4. Reduce cargo capacity when operating on rough or
hilly terrain.
5. Balance loads evenly and secure them. Braking could
shift the load and affect vehicle stability.
6. Never operate vehicle with the cargo bed raised.
7. Operate cargo bed dump with vehicle stationary and
parking brake locked. Do not dump while moving.
8. Operate hydraulic dump (if equipped) on level ground
only.
9. Operate dump from operator's seat only.
10. Do not place hands or body under the cargo bed when
lowering bed.
4. OPERATING HYDRAULIC OUTLET
DRIVEN EQUIPMENT (IF EQUIPPED)
1. Before installing or using hydraulic outlet driven
equipment, read the manufacturer's manual and
review the safety labels attached to the equipment.
2. Wait until all moving components have completely
stopped before getting off the vehicle, connecting,
disconnecting, adjusting, cleaning, or servicing any
hydraulically driven equipment.
3. When operating stationary
equipment, always apply the vehicle parking brake
and place chocks behind and in front of the rear
wheels. Stay clear of all rotating parts. Never step over
rotating parts.
SAFE OPERATION
hydraulically driven
3
-