Table of Contents
Advertisement
Utility screen outlines
Setting Item/Description
04 Finisher Adjustment
Adjust the settings related to the finisher (FS-520/FS-607).
05 Scanner Adjustment
Adjust the settings related to the scanner.
•
•
•
CS665 Pro
08 Perfect Binder Adjustment
Adjust the settings related to the Perfect Binder
PB-501/PB-502.
•
Cover Trimming Adjustment:-128 to +127 (1 step =
0.1mm)
•
Cover Lead Edge Adjustment:-128 to +127 (1 step =
0.1mm)
•
Spine Corner Forming Position Adjustment:-128 to +127
(1 step = 0.1mm)
•
Pasting Start Position Adjustment:-128 to +127 (1 step =
0.1mm)
•
Pasting Finish Position Adjustment:-128 to +127 (1 step
= 0.1mm)
•
Paste Formation Finish Position Adjustment:-128 to
+127 (1 step = 0.1mm)
•
Temperature Adjustment:
Melt Tank -Low 180 to 190 °C (1 step = 1 °C)
Pasting Roller 160 to 170 °C (1 step = 1 °C)
•
Sub Compile CD Width Adjustment:-20 to +20 (1 step =
0.1mm)
•
Clamp CD Width Adjustment:-20 to +20 (1 step =
0.1mm)
•
Cover Up/Down CD Width Adjustment:-20 to +20 (1 step
= 0.1mm)
•
Clamp FD Position Adjustment:-20 to +20 (1 step =
0.1mm)
01 Saddle Stitcher Stopper Adj. (FS-607 Only)
Adjust the staple positions in widthwise direction of paper
using Fold & Staple mode.
-128 to +127 (1 step = 0.1mm)
02 Half Fold Stopper Adjustment (FS-607 Only)
Adjust the double-folding position using Multi Half Fold
mode.
-128 to +127 (1 step = 0.1mm)
03 Punch Adjustment (FS-520/FS-607)
Adjust the punch position operated by Punch Kit PK-
512/PK-513.
•
Vertical Position Adj.:-128 to +127 (1 step = 0.1mm)
•
Horizontal Position Adj.:-50 to +50 (1 step = 0.1mm)
•
Registration Adjustment:-20 to +20 (1 step = 0.8mm)
•
Paper Edge Detect Sensor Adj.
04 Tri-Fold Adjustment (FS-607 Only)
Adjust the three-folding positions using Multi Tri-Fold mode.
-128 to +127 (1 step = 0.1mm)
05 2 Position Staple Pitch Adjustment (FS-607 Only)
Adjust the staple pitch in Staple and Fold & Staple modes.
-128 to +160 (1 step = 1mm)
06 Paper Inserter Tray Size Adj. (FS-520/FS-607)
Adjust the tray size of upper/lower tray of the Paper Inserter
PI-502.
07 Output Quantity Limit (FS-520/FS-607)
Specify the quantity limit for each of Staple, Fold & Staple,
Multi Half Fold, and Multi Tri-Fold modes.
08 Curl Adjustment (FS-520/FS-607)
Adjust the compression fixing amount of paper exit decurler
roller as a remedy for the crease produced in Tri-Fold, inside
printing mode.
Restart Timing Adjustment: -10 to +20 (1 step = 0.1mm)
Centering Adjustment: -30 to +30 (1 step = 0.1mm)
FD-Mag. Adjustment: -40 to +40 (1 step = 0.05%)
Default
2
Simplex (Tri-Fold 64-80g/m
:
Inside Print): Large
2
Simplex (Tri-Fold 81-105g/m
Inside Print): Small
Simplex (Print Side <Except Tri-
Fold>: Front): Small
Simplex (Print Side: Back):
Large
Duplex: Middle
4
:
4-17
Advertisement
Table of Contents
